Related Manuals for Teknik 5418295
Summary of Contents for Teknik 5418295
- Page 1 Teknik www.teknikoffice.co.uk For things 'n such. Hutch for Scribed Oak Storage Desk (5418294) 18295 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
- Page 2 Table of Contents Assembly Tools Required Part Identifi cation No. 2 Phillips Screwdriver Tip Shown Actual Size Hardware Identifi cation Assembly Steps 5-17 Hammer Not actual size Short Screwdriver Safety Skip the power trip. This time. Page 2...
-
Page 3: Part Identification
Now you know Part Identifi cation our ABCs. å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identifi cation to help identify similar parts. RIGHT END (1) SHELF (1) SKIRT (1) -
Page 4: Hardware Identification
Hardware Identifi cation å Screws are shown actual size. You may receive extra hardware with your unit. MOLDING HIDDEN CAM - 12 CAM DOWEL - 12 CONNECTOR - 2 36P CAM COVER - 10 NAIL - 36 METAL PIN - 11 BLACK 9/16"... - Page 5 Step 1 Assemble your unit on a carpeted fl oor or on the empty å carton to avoid scratching your unit or the fl oor. Push twelve HIDDEN CAMS (1F) into the ENDS (A and B), å UPRIGHT (C), SHELF (E), and SKIRT (I). Then, insert the metal end of a CAM DOWEL (2F) into each HIDDEN CAM.
- Page 6 Step 2 Tap two MOLDING CONNECTORS (17F) into the notches å in the MOLDINGS (J, K, and L). Use your hammer to tap the MOLDING CONNECTOR (17F) into the notches in the MOLDINGS. Flat end Flat end Page 6...
- Page 7 Step 3 Turn the MOLDINGS (J, K, and L) over and fasten them å to the TOP (D). Use nine BLACK 1-1/4" FLAT HEAD Remember: SCREWS (7S). Righty tighty. Lefty loosey. Finished surface BLACK 1-1/4" FLAT HEAD SCREW (9 used in this step) Finished surface Rounded edge Page 7...
- Page 8 Step 4 Fasten the RIGHT END (A) to the RIGHT MOLDING (K). å Tighten two HIDDEN CAMS. S u r f a c H I D D E N i t h Curved edge Caution Do not stand the unit upright without the BACK fastened.
- Page 9 Step 5 Insert three METAL PINS (1R) into the holes shown in the å TOP (D). Slide the DIVIDERS (H) onto the METAL PINS (1R) in the å TOP (D). Now, insert six METAL PINS (1R) into the other end of the å...
- Page 10 Step 6 Fasten the SHELF (E) to the RIGHT END (A). Tighten two å HIDDEN CAMS. Maximum Arrow 210 degrees NOTE: Be sure the METAL PINS in the DIVIDERS (H) å insert into the holes in the SHELF. Minimum 190 degrees Finished edge Page 10...
- Page 11 Step 7 Using your short screwdriver, fasten the UPRIGHT (C) to å the TOP (D) and SHELF (E). Tighten four HIDDEN CAMS. Don't worry. It isn't Rome. This can be built in a day. Curved edge Surface with HIDDEN CAMS Maximum Arrow 210 degrees...
-
Page 12: Hidden Cam
Step 8 Insert a METAL PIN (1R) into the UPRIGHT (C). å Fasten the SKIRT (I) to the UPRIGHT (C). Tighten one å HIDDEN CAM. NOTE: Be sure the METAL PIN in the UPRIGHT inserts å into the SKIRT. Curved edge Surface with holes Maximum Arrow... - Page 13 Step 9 Insert a METAL PIN (1R) into the LEFT END (B). å Fasten the LEFT END (B) to the LEFT MOLDING (L) and å SKIRT (I). Tighten three HIDDEN CAMS. NOTE: Be sure the METAL PIN in the LEFT END inserts into å...
- Page 14 Step 10 Push a CAM COVER (36P) onto each visible HIDDEN CAM in å the ENDS (A and B), UPRIGHT (C), and SHELF (E). Hey! It's starting to look like something! (10 used) To cover HIDDEN CAMS Page 14...
- Page 15 Step 11 Carefully turn your unit over onto its front edges. Unfold the å Caution RIGHT BACK (F) and lay it over your unit. Do not stand the unit upright without the Make equal margins along the top and outer side edge of å...
- Page 16 Step 12 Unfold the LEFT BACK (G) and lay it over your unit. å Caution Make equal margins along the top and outer edge of the å Do not stand the unit upright without the LEFT BACK (G). Push on opposite corners of your unit if BACK fastened.
- Page 17 Step 13 Carefully stand your unit upright. å The instructions for fastening your unit to the 418294 Pro Tip: Lift with your å Computer Desk is in the Computer Desk assembly manual. legs. And, you know, your arms. You will use seven NAILS (1N) and three BLACK 1-7/8" FLAT HEAD SCREWS (2S) from your Hutch hardware to fasten to the Computer Desk.
- Page 18 WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded shelves and drawers. •...