Related Manuals for Teknik 5418269
Summary of Contents for Teknik 5418269
- Page 1 Teknik www.teknikoffice.co.uk The original desktop. Writing Desk 5418269 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
- Page 2 Table of Contents Assembly Tools Required Part Identifi cation No. 2 Phillips Screwdriver Tip Shown Actual Size Hardware Identifi cation Assembly Steps 5-18 Hammer Not actual size Français 19-21 Español 22-24 Skip the power trip. Safety 25-26 This time. Warranty Page 2...
-
Page 3: Part Identification
Now you know Part Identifi cation our ABCs. å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identifi cation to help identify similar parts. RIGHT END (1) LEFT END (1) HUTCH RIGHT END (2) -
Page 4: Hardware Identification
Hardware Identifi cation å Screws are shown actual size. You may receive extra hardware with your unit. 35GA CABINET RIGHT - 1 35GB CABINET LEFT - 1 35GC DRAWER RIGHT - 1 35GD DRAWER LEFT - 1 10A SLIDE CAM - 2 HIDDEN CAM - 20 CAM DOWEL - 14 7F TWIST-LOCK... - Page 5 Step 1 Assemble your unit on a carpeted fl oor or on the empty å carton to avoid scratching your unit or the fl oor. To begin assembly, push a SAUDER TWIST-LOCK® å FASTENER (7F) into the large holes in the HUTCH ENDS (C and M).
- Page 6 Step 2 Push twenty HIDDEN CAMS (1F) into the ENDS (A and B), å UPRIGHT (D), and MODESTY PANEL (G). Then, insert the metal end of a CAM DOWEL (2F) into each HIDDEN CAM, except the long edges of the ENDS (A and B). Do not tighten the HIDDEN CAMS in this step.
- Page 7 Step 3 Turn six CAM SCREWS (8F) into the FRONT LEGS (I and J). å Fasten the ENDS (A and B) to the FRONT LEGS (I and J). å Tighten six HIDDEN CAMS. (6 used) Angled edge These surfaces should be even. These surfaces should be even.
- Page 8 Step 4 Fasten the REAR LEGS (K) to the ENDS (A and B). Use six å BLACK 1-7/8" FLAT HEAD SCREWS (2S). Some assembly (and snacks) required. Angled edge BLACK 1-7/8" FLAT HEAD SCREW (6 used in this step) Page 8...
- Page 9 Step 5 Fasten the CABINET RIGHT (35GA) to the RIGHT END (A) å and the CABINET LEFT (35GB) to the UPRIGHT (D). Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #3. GOLD 5/16" FLAT HEAD SCREW Roller end (4 used in this step) Roller end...
- Page 10 Step 6 Fasten the MODESTY PANEL (G) to the ENDS (A and B). å Tighten six HIDDEN CAMS. S u r f a c H I D D E N i t h i t h f a c S u r D E N H I D S u r...
- Page 11 Step 7 First, fi ll four holes in the TOP (E) 1/4 to 1/2 full with GLUE (54M). å Then, insert four WOOD DOWELS (15F) into the holes. Wipe away the excess GLUE. Next, place drops of GLUE (54M) onto the WOOD DOWELS (15F) å...
- Page 12 Step 8 Fasten the UPRPIGHT (D) to the TOP (E). Tighten two å HIDDEN CAMS. Maximum Arrow 210 degrees Fasten the UPRIGHT (D) to the MODESTY PANEL (G). Use å one BLACK 1-7/8" FLAT HEAD SCREW (2S). Minimum 190 degrees BLACK 1-7/8"...
-
Page 13: Twist-Lock® Fastener
Step 9 Carefully stand your unit upright. å How to use the SAUDER TWIST-LOCK ® FASTENER Fasten the HUTCH UPRIGHTS (C and M) to the TOP (E). 1. Insert the dowel end of the FASTENER into the hole of the å... - Page 14 Step 10 IMPORTANT: Do not pick up or move your unit by using å the TOP (F). Fasten the BACK (H) to your unit using the NAILS (1N). å NOTE: Be sure to tap NAILS into the holes that line up å...
- Page 15 Step 11 The tabs should insert freely With the palm of your hand, into the slots. Gently tilt the tap the DRAWER BOTTOM DRAWER SIDES side to side down into the groove. until the tabs slip into the slots. fi n i s h r f a D716...
- Page 16 Step 12 Insert a SLIDE CAM (10A) into the DRAWER SIDES (D20 and D21). å Fasten the DRAWER RIGHT (35GC) to the DRAWER RIGHT SIDE (D20) å and the DRAWER LEFT (35GD) to the DRAWER LEFT SIDE (D21). Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #3. NOTE: The screw head in the CAM must be visible through the slotted å...
- Page 17 Step 13 To insert the drawer into your unit, tip the front of the å drawer down and drop the rollers on the drawer behind the rollers on the unit. Lift the front of the drawer up and slide it into the unit. Push a CAM COVER (12P) onto each visible HIDDEN CAM.
- Page 18 Step 14 To make adjustments to the drawers, loosen SCREW #3 in the SLIDES a 1/4 turn, then turn the CAM å clockwise or counter-clockwise. Notice how the drawer raises or lowers as you turn the CAM. The higher the screw in the oblong hole, the higher your drawer front will be. The lower the screw, the lower the drawer front.
- Page 19 WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded shelves and drawers. •...