Related Manuals for Teknik Contemporary Bureau 5416966
Summary of Contents for Teknik Contemporary Bureau 5416966
- Page 1 Teknik www.teknikoffice.co.uk For all your newfangled gadgetry. Contemporary Bureau 5416966 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
- Page 2 Table of Contents Assembly Tools Required Part Identifi cation No. 2 Phillips Screwdriver Tip Shown Actual Size Hardware Identifi cation Assembly Steps 5-22 Hammer Not actual size Français 23-25 Español 26-28 Skip the power trip. Safety 29-30 This time. Warranty Page 2...
- Page 3 Now you know Part Identifi cation our ABCs. å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identifi cation to help identify similar parts. RIGHT END (1) BACK (1) SHELF MOLDING (1)
-
Page 4: Table Of Contents
Hardware Identifi cation å Screws are shown actual size. You may receive extra hardware with your unit. (EXTENSION SET SHOWN SEPARATED) EXTENSION RAIL - 2 EXTENSION SLIDE - 2 HIDDEN CAM - 20 CAM DOWEL - 16 CAM SCREW - 4 WOOD DOWEL - 4 CROSS SLOTTED DOWEL - 4 METAL BRACKET - 6... - Page 5 Step 1 Assemble your unit on a carpeted fl oor or on the empty å carton to avoid scratching your unit or the fl oor. Push twenty HIDDEN CAMS (1F) into the ENDS (A and Arrow å B) SLIDE SHELF (G), SHELF (H), LEGS (I and J) and FRONT/BACK SKIRTS (N).
- Page 6 Step 2 Turn four CAM SCREWS (8F) into the LEGS (I and J). å Remember: Righty tighty. Lefty loosey. Page 6...
-
Page 7: Extension Rail
Step 3 Separate the EXTENSION SLIDES (Q) from the å EXTENSION RAILS (P) as shown in the upper diagram. Be prepared, the parts are greasy. Fasten the EXTENSION RAILS (P) to the ENDS (A and B). å Use four GOLD 5/16” FLAT HEAD SCREWS (3S). NOTE: For each EXTENSION RAIL, turn a SCREW into å... -
Page 8: Black 9/16" Large Head Screw
Step 4 Fasten six METAL BRACKETS (4G) to the FRONT/BACK å SKIRTS (N) and SHELF UPRIGHTS (C). Use six BLACK 9/16" LARGE HEAD SCREWS (1S). NOTE: Be sure the BRACKETS are even with the edges å of the SKIRTS and UPRIGHTS. BLACK 9/16"... - Page 9 Step 5 Fasten a RIGHT FRONT/LEFT REAR LEG (I) and a LEFT å FRONT/RIGHT REAR LEG (J) to a FRONT/BACK SKIRT (N). Repeat this step for the remaining LEGS (I and J) å and SKIRT (N). Surface with HIDDEN CAMS Surface with HIDDEN CAMS Page 9...
- Page 10 Step 6 Fasten the LEFT END (B) to the TOP (D). Tighten two HIDDEN CAMS. å These two small holes must be here. These holes must be here. Caution Start Tighten Risk of damage or Arrow injury. HIDDEN CAMS must be completely Arrow Maximum tightened.
- Page 11 Step 7 Insert two METAL PINS (1R) into the TOP (D). å Push the REAR BRACE (O) onto the METAL PINS (1R). å NOTE: The REAR BRACE comes two colored. You have the å option to fasten the BRACE with either color inside or out. Page 11...
- Page 12 Step 8 Fasten the SHELF (H) to the LEFT END (B). Tighten two å HIDDEN CAMS. Side Step: Make nachos. (Optional, but Fasten the SHELF (H) to the REAR BRACE (O). Use two å recommended.) BLACK 1-7/8" FLAT HEAD SCREWS (2S). BLACK 1-7/8"...
-
Page 13: Black 9/16" Pan Head Screw
Step 9 Fasten the RIGHT END (A) to the SHELF (H) and TOP (D). å Tighten four HIDDEN CAMS. Maximum Arrow 210 degrees Fasten two MAGNETIC CATCHES (12I) to the SHELF (H). å Use four BLACK 9/16" PAN HEAD SCREWS (51S). Minimum 190 degrees BLACK 9/16"... - Page 14 Step 10 Fasten the BOTTOM (E) to the ENDS (A and B). Use four å BLACK 1-7/8" FLAT HEAD SCREWS (2S). This hole must be here. BLACK 1-7/8" FLAT HEAD SCREW (4 used in this step) This hole must be here. Page 14...
- Page 15 Step 11 Fasten the LEGS (I and J) to the BOTTOM (E). Tighten å four HIDDEN CAMS. Maximum Arrow 210 degrees Fasten the FRONT/BACK SKIRTS (N) to the BOTTOM (E). å Use two BLACK 9/16" LARGE HEAD SCREWS (1S). Minimum 190 degrees BLACK 9/16"...
-
Page 16: 109S
Step 12 Push four CROSS SLOTTED DOWELS (28F) into the å SIDE SKIRTS (L). Fasten the SKIRTS (L) to the LEGS (I and J). Use four å GOLD 2-3/4" FLAT HEAD BOLTS (109S). The DOWELS should be on the inside surface. The DOWELS should be on the inside surface. - Page 17 Step 13 Carefully turn your unit over onto its front edges. å Caution NOTE: The BACK comes two colored. Unfold the BACK (F) å Do not stand the unit upright without the and lay it over your unit with the preferred color on each side. BACK fastened.
-
Page 18: Metal Bracket
Step 14 Push four WOODEN DOWELS (15F) into the å SLIDING SHELF (G). Fasten the SLIDING SHELF UPRIGHTS (C) to the SLIDING Maximum Arrow å SHELF (G). Use four BLACK 9/16" LARGE HEAD SCREWS (1S). 210 degrees NOTE: Be sure the WOODEN DOWELS insert into the å... - Page 19 Step 15 Fasten the EXTENSION SLIDES (Q) to the SLIDING å SHELF UPRIGHTS (C). Use four GOLD 5/16" FLAT HEAD SCREWS (3S). Open end Open end GOLD 5/16" FLAT HEAD SCREW (4 used in this step) Page 19...
- Page 20 Step 16 Fasten the PIVOT HINGES (41H) to the DOORS (M) as å shown. Use eight BLACK 7/8" FLAT HEAD SCREWS (31S). BLACK 7/8" FLAT HEAD SCREW Fasten the STRIKE PLATE BRACKET (14I) to the DOORS (M) å (10 used in this step) as shown.
- Page 21 Step 17 Carefully stand your unit upright. å 1. Lay the WASHER (9I) over the hole in the BOTTOM (E). Hey! It's starting to look å like something! 2. Insert the PIVOT HINGE BRACKET (54G) over the post å of the upper PIVOT HINGE (41H). 3.
- Page 22 Step 18 Push a CAM COVER (50P) onto the HIDDEN CAMS on the å ENDS (A and B). To insert the SLIDING SHELF into your unit, line up the å EXTENSION SLIDES on the SHELF with the EXTENSION RAILS on the unit and push the SHELF into the unit until it is fully inserted.
- Page 23 WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded shelves and drawers. •...