Changing Recording Times; Configuring Alarm Inputs - Monacor IOR-204 Instruction Manual

Select All Clear All
Channel CH1
Switch Enable
Sensitivity 4
Fig. 6-19 Detection fields for the motion detection feature

6.6.5 Changing recording times

According to the factory settings, all camera channels to which
a camera is connected will be recorded from 00:00 – 24:00
(marked by green bars in fig. 6-20). To change this setting:
1) Call up the tile menu and then, in the tile "Record", click
the menu item "Record".
2) The submenus "Record" and "Record Schedule" are
available. To change the recording times, click "Record
Schedule".
Record Record Schedule
Channel
CH1
0 2 4 6 8
SUN
MON
TUE
WED
THU
FRI
SAT
Fig. 6-20 Recording schedule
3) In the upper left, after "Channel", the selected channel
is specified in the field highlighted by a blue frame. Select
the respective channel here.
4) To the right of the schedule, four coloured circles are avail-
able. Select the appropriate circle to select the event for
which the recording time is to be changed:
Normal recording without any event; the correspond-
Normal
ing times are shown in green in the schedule
Recording when a motion is detected by the recorder;
Motion
the corresponding times are shown in yellow
Recording when an alarm is triggered via the contacts
IO SENSOR (12) or ALARM IN (17) (chapter 6.6.6); the
corresponding times are shown in red
Recording when a motion is detected by a camera
PIR with an integrated IR motion sensor; the correspond-
ing times are shown in purple
5) To define the recording times, keep the left mouse button
pressed and move the mouse pointer over the time range
desired. Individual half-hour blocks can be selected by a sim-
ple click. Proceed in the same way to delete recording times.
6) To use the settings for additional channels, click "Copy";
for a reset to the factory settings, click "Default".
7) To save the settings, click "Apply". Click "OK" to confirm
the message "Save parameters successful!".
10 12 14 16 18 20 22
Copy Default

6.6.6 Configuring alarm inputs

When alarm sensors such as motion detectors or photoelectric
sensors are connected to the contacts SENSOR (12) or ALARM
IN (17), configure the alarm inputs: Call up the tile menu and
then, in the tile "Alarm", click the menu item "I / O".
I/O
Alarm In Alarm Type
Local<-1 Normally-Open
Local<-2 Normally-Open
Local<-3 Normally-Open
Local<-4 Normally-Open
Fig. 6-21 Menu for the alarm inputs; use the scrollbar to show further
settings options
Menu item
Alarm In
Normal
Alarm Type
Motion
IO
PIR
Buzzer
Alarm Out
Latch Time
Apply
Channel
Post Recording
Show Message
Send Email
Full Screen
Picture to Cloud
Video to Cloud
Copy
Default
Apply
Buzzer Alarm Out Latch Time Channel Post Recording
Disable 10 s
Disable 10 s
Disable 10 s
Disable 10 s
Copy
Function
Number of the alarm input
To select the contact type
Normally-Open
Normally-Close
OFF = input signal will not be evaluated
Duration of the alarm sound
To route the alarm to the normally open relay
contact ALARM (12) or ALARM OUT (17), click
the symbol and then, in the window "
Local->...", click the activation field
contact can be loaded with ⎓ 30 V, 1 A.
Switching time for relay contact and alarm sym-
bol in the camera image
To select the channels that are to be recorded
when an alarm is triggered, click the symbol
The time in which alarm-triggered recordings
are possible must be defined in the schedule:
tile "Record", menu item "Record"  "Record
Schedule". Click the red selection circle "IO" and
then, with the left mouse button pressed, move
the mouse pointer over the days / hours (also see
chapter 6.6.5)
Duration of an alarm-triggered recording
An alarm will be indicated by the symbol
camera image
In case of an alarm, an e-mail will be sent;
to make the e-mail settings, call up the tile
"Network" and then click the menu item "Email"
The corresponding channel will be displayed in
full-screen mode
In case of an alarm, an image or video will be
uploaded to a cloud; to make the respective
settings, call up the tile "Device" and then click
the menu item "Cloud"
To use the settings of an alarm input for addi-
tional inputs
To reset this menu to its factory settings
To save the settings
Show Me
30 s
30 s
30 s
30 s
Default Apply
. The relay
.
in the
41