Monacor IOR-204 Instruction Manual page 37

4) The submenus "Date / Time", "NTP" and "DST" are availa-
ble. The name of the submenu currently called up is under-
lined and shown in turquoise. To go to a different submenu,
click the name of the submenu.
Menu item Note
Date and Time
Date Make sure to update the date and the time
so that it will be possible to search recordings in
Time
specific time ranges.
Select the date format:
MM / DD / YYYY
Date Format
YYYY-MM-DD
DD/ MM / YYYY
Time Format 24-hour format or 12-hour format
Time Zone For Great Britain, set to "GMT".
NTP (Network Time Protocol)
Enable NTP if the time is to be automatically set
Enable NTP
via the Internet.
Server Address
Predefined setting: pool.ntp.org
Update Now Click this option to instantly update the time
DST (Daylight Saving Time)
Enable DST for an automatic change between
Enable DST
daylight saving time and standard time
Time Offset Set to 1 hour
For the option "Week", for example, the start
time "Mar.", "The Last" and "Sun" must be set.
DST Mode
For the option "Date", the date of the time
change must be set each year again.
Start Time Start of the daylight saving time
End Time
End of the daylight saving time
5) If required, click the button "Previous" to go back to the
previous menu.
6) When the time and the date have been set, click "Next".
A menu for adding IP cameras will appear:
IP Camera
No. IP Address/Domain Port Manufact
Search
Fig. 6-7 Menu for adding IP cameras
If only cameras are used that are directly connected to the
recorder via the jacks LAN (5, 6), continue with step 7).
a) IP cameras can only be added when they have been
connected to the network (see instruction manual of
the camera).
b) Shortly after the menu "IP Camera" has been called up,
the left side of the menu will list the cameras available
in the network. If required, click the button "Search"
to search for IP cameras again.
Wizard
Channel Edit State IP Address/Dom
POE CH1 10.10.25.151
POE CH2 10.10.25.152
POE CH3
POE CH4
POE CH5
POE CH6
POE CH7
POE CH8
Channel Delete
Previous Next Cancel
c) To select a camera, click the camera desired in the list
on the left side of the menu.
d) To select a free channel for the camera, click the corre-
sponding line on the right side of the menu.
e) Click the blue arrow
submenu "Add IP Camera" will appear. If required, make
additional settings in the submenu "Add IP camera",
and then click "Add".
f) When the settings are correct, the camera image will
appear in the corresponding channel window after a
short while. To make sure that the settings are correct,
it is possible to open a separate window with the live
image: click the symbol
responding camera.
7) When the IP cameras have been added, click "Next". The
menu for setting the hard disk will appear:
Disk
No. Model
1* WDC WD10EURX-63UY4Y0 WD-WCC4J0FXUDP
Overwrite Auto Format HDD
Fig. 6-8 Settings for the hard disk
The line „No. Model Serial No. ..." shows information
with regard to the hard disk. To set the overwrite mode,
open the pop-up menu: Click the symbol ∨ in the line
"Overwrite" at the bottom of the menu.
Overwrite mode
Setting Function
Auto When the hard disk is full, the oldest recordings
(factory setting) will be overwritten.
No recordings will be overwritten. When the
hard disk is full, the symbol
OFF
it will not be possible to make any further
recordings.
1 Day Recordings can be overwritten after the storage
2 Days time selected. When the hard disk is full earlier,
⋮
it will not be possible to make any further
96 Days recordings.
To format a hard disk: In the column "No.", click the corre-
sponding selection field
click the button "Format HDD".
8) When the settings for the hard disk have been made, click
"Next". The menu for the monitor resolution will appear.
in the centre of the menu; the
in the menu line of the cor-
Wizard
Serial No. Firmware State Free/Total
01.01A01 Normal 657G/931G 362Hour
Previous Next
will appear and
to select the hard disk and then
Free/Tot
Cancel
37