Factory Setting; Saving The Recorder Configurations; Operation; User Lock - Monacor IOR-204 Instruction Manual

3) The times in which analyses are to be made and eval-
uated, must be entered in the schedule. In the header
"PID LCD ... CC Statistics", click "Schedule".
PID LCD SOD PD FD
Channel CH1
0 2 4 6
SUN
MON
TUE
WED
THU
FRI
SAT
Fig. 6-28 Schedule for intelligent image analysis
example: Monday to Saturday, each day from 7 am to 10 pm
4) The procedure for entering the analysis times is the same
as for entering the recording times (chapter 6.6.5).

6.6.11 Factory setting

When the recorder is reset to its factory settings, all settings
the user may have made will be lost. However, it is possible
to save the settings made on a USB flash drive first and then,
after the reset, to load them onto the recorder (chapter 6.6.12).
1) Call up the tile menu and then, in the tile "System", click
the menu item "Maintenance".
2) In the menu "Maintenance", click "Load Default" to call
up the submenu for resetting.
Setup
Channel
General
Multi-User
Maintenance
IP Camera Maintain
Information
Fig. 6-29 Menu for resetting to factory settings
3) For the reset, select all or only specific options.
4) Click "Apply". Click "OK" to confirm the message "Save
parameters successful!"

6.6.12 Saving the recorder configurations

You can save all settings of the recorder on an external storage
device (e. g. USB flash drive) as a precaution. It is also possible
to save different configurations and to retrieve them when
required.
1) Configure the recorder as desired.
2) Connect an external storage device to one of the USB ports
of the recorder.
3) Call up the tile menu and then, in the tile "System", click
the menu item "Maintenance".
4) To call up the submenu for saving, click "Parameter Man-
agement" in the menu "Maintenance" (Fig. 6-29).
44
CC Sound Detection Occlusion Detection Schedule
8 10 12 14 16 18
Copy
Record Alarm Network Device System
Log Load Default Upgrade Parameter Management
Select All
Channel
Record
Alarm
Network
Device
System
5) Click "Save Settings". The window "Save Settings" will be
shown; make all settings for saving and click "OK". The
name "DEVICE_Settings" will be assigned to the config-
uration file.
CC Statistics
6) If applicable, save different configurations in different fold-
20 22 ers to make sure that a configuration file already saved will
not be overwritten.
7) To call up a configuration saved on an external storage
device, click "Load Settings".
7

Operation

The most comfortable way to operate the recorder is using the
Default Apply
mouse. Therefore, these instructions do not focus on operation
by means of a remote control.
Switch on the recorder with the rocker switch (14) located on
the rear of the unit. After a few seconds, the MONACOR logo
will appear on the monitor connected:
Then the view for live surveillance will appear (chapter 7.3).

7.1 User lock

According to the factory settings, the recorder is protected
by a user lock against unauthorized access. The recorder will
be locked approx. 1 minute after a menu has been exited. To
Auto Reboot
unlock the recorder, show the toolbar and call up the start
menu:
1) Press the right mouse button or move the mouse pointer
to the centre of the lower edge of the screen.
Fig. 7-1 Toolbar; depending on the recorder model, additional sym-
2) Click the first symbol to the left
menu:
Apply
admin
Search
Setup
Unlock
Shutdown
Fig. 7-2 Start menu
3) In the start menu, click "Unlock". (If the recorder is not
locked, the menu item "Screen Lock" will be available
instead. When you click this menu item, the recorder will
be locked immediately.)
Fig. 7-3 Window to disable the lock
HD
SD
bols may be available
Unlock
Current User: admin
Device ID 000000 (000000)
Password
Forgot Password Unlock
i 09/15/2019 14:27:38
to call up the start HD
SD
Show Password
Cancel