Wilding Wallbeds King Size with Storage Headboard Instruction Booklet

Hide thumbs

page of 20

/ 20
Bookmarks

Quick Links

Download this manual

For Wallbed models:

KING SIZE

WITH STORAGE

HEADBOARD

Watch step by step installation instructions at:

https://www.wallbedsbywilding.com/wallbed-installation-studio-series/

WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND

FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION PROCESS COULD RESULT IN SEVERE

PERSONAL INJURY TO USER OR DAMAGE TO PRODUCT. PLEASE CONTACT CUSTOMER SERVICE AT

866-725-6401 FOR ANY QUESTIONS.

INSTRUCTION BOOKLET #C24

Revision 4/19.1

Need help?

Do you have a question about the King Size with Storage Headboard and is the answer not in the manual?

Questions and answers

Summary of Contents for Wilding Wallbeds King Size with Storage Headboard

Page 1 For Wallbed models: KING SIZE INSTRUCTION BOOKLET #C24 WITH STORAGE HEADBOARD Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION PROCESS COULD RESULT IN SEVERE PERSONAL INJURY TO USER OR DAMAGE TO PRODUCT.
Page 3 studsensor...
Page 5 Left Side Board Right Side Board...
Page 6 The required number of springs in the Lift Mechanisms varies with the different weights of mattresses. If you purchased your mattress with your bed from Wilding Wallbeds refer to the chart to the right. This will also be a good reference point for mattresses not purchased with your Wall bed.
Page 7 Hardware needed for next step: Step 4: Lay the right Side Board down and screw 14 Connecting Bolts into the holes provided as shown. Repeat the process with the left Side Board which will require 15 Connecting Bolts. Page 3...
Page 8 Page 4...
Page 9 Page 5...
Page 10 Step 6: Stand the Bed Cabinet up against the wall where you intend to have it installed. Page 6...
Page 11 Step: 7: Using a Stud Finder locate and mark the studs in your wall behind the Bed Cabinet. Attach the “L” brackets to the top, back of the Bed Cabinet cor- responding to where the studs are located. Now attach the “L” brackets to the studs in the wall using six 2”...
Page 12 Foot rail Side rail Side rail Head rail...
Page 13 Page 7...
Page 15 Center Stiffeners FOOT RAIL 3.5” Stiffener #1 Stiffener #2 Stiffener #3 WARNING! DO NOT STRIP SCREWS. SCREWS SHOULD BE TIIGHT BUT NOT STRIPPED. Stiffener #4 Stiffener #5 HEAD RAIL...
Page 17 Step 17: As illustrated below, insert the Allen Head Bolt through bolt hole # 1 and tighten it down securely using a Nylock Nut. Now insert a 5/16” x 1” Hex head bolt through hole # 3 and thread the Nylock nut ONLY UNTIL THE NUT IS FLUSH WITH THE END OF THE BOLT.
Page 18 IF YOU PURCHASED LIGHTS FOR YOUR WALLBED YOU MUST STOP RETURN TO THE LIGHT KIT INSTRUCTIONS STEP 6 AND INSTALL THE SAFETY CUT OFF DEVICE BEFORE MOVING ON. IMPORTANT! As instructed in step 17, Bolt #3 should be loose enough to slip into the notch at the end of the Tension Arm See illustration below.
Page 19 Step 22: Insert a 5/16” x 1” Hex Head bolt through hole #2 and tighten a 5/16” Nylock nut onto the bolt. Now tighten the nut and bolt in hole #3. Repeat step 22 on the other side of the bed unit.
Page 20 Illustration 12 Push bed over at the bottom to align 3/16”Drill 3/16”Drill...

This manual is also suitable for:

Studio series