Advertisement
Quick Links
For Wallbed models:
KING SIZE PARK CITY
WITH STORAGE
HEADBOARD
Watch step by step installation instructions at:
https://www.wallbedsbywilding.com/wallbed-installation-studio-series/
WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND
FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION PROCESS COULD RESULT IN SEVERE
PERSONAL INJURY TO USER OR DAMAGE TO PRODUCT. PLEASE CONTACT CUSTOMER SERVICE AT
866-725-6401 FOR ANY QUESTIONS.
INSTRUCTION BOOKLET #C124
Revision 4/16 C124
Advertisement
Related Manuals for Wilding Wallbeds PARK CITY
Summary of Contents for Wilding Wallbeds PARK CITY
- Page 1 For Wallbed models: KING SIZE PARK CITY INSTRUCTION BOOKLET #C124 WITH STORAGE HEADBOARD Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION PROCESS COULD RESULT IN SEVERE PERSONAL INJURY TO USER OR DAMAGE TO PRODUCT.
- Page 3 studsensor...
- Page 5 Left Side Board Right Side Board Step 2: Install Springs in the Lift Mechanisms Number of Springs Bed Size King Queen NOTE: After you have completed installing and checking operation of your Wallbed, you may find it necessary to add or remove springs to achieve the correct lift effort of between 5 and 10 pounds.
- Page 6 Step 4: Lay the right Side Board down and screw 14 Connecting Bolts into the holes provided as shown. Repeat the process with the left Side Board which will require 15 Connecting Bolts. Page 2...
- Page 7 Page 3...
- Page 8 Page 4...
- Page 9 Step 6: Stand the Bed Cabinet up against the wall where you intend to have it installed. Page 5...
- Page 10 Step: 7: Using a Stud Finder locate and mark the studs in your wall behind the Bed Cabinet. Attach the “L” brackets to the top, back of the Bed Cabinet cor- responding to where the studs are located. Now attach the “L” brackets to the studs in the wall using six 2”...
- Page 11 Step 9: Arrange the Mattress Rails on the Face Panels as shown. Foot rail HELPFUL HINT: the “Head Rail” Side rail Side rail refers to the end that is closest to the Head rail Bed Cabinet while assembling and will be where your head is while sleeping.
- Page 12 Hardware needed for next 2 steps most from Pack #3 x 16 1/2” x 3/4” Black Barrel 4 hole corner bracket (Leg Stop) Step 10: From hardware pack 3 locate the hardware shown above. Finger Panel Saver tighten the hardware as shown in illustration 7 connecting the Foot Rail to the (from rails box) Side Rail using the 4 hole corner bracket.
- Page 13 Hardware and parts needed for next steps x Approx. 118 5/8” Square Pan head screw (Hardware pack #7)
- Page 14 Center Stiffeners...
- Page 16 Step 17: As illustrated below, insert the Allen Head Bolt through bolt hole # 1 and tighten it down securely using a Nylock Nut. Now insert a 5/16” x 1” Hex head bolt through hole # 3 and thread the Nylock nut ONLY UNTIL THE NUT IS FLUSH WITH THE END OF THE BOLT.
- Page 17 IF YOU PURCHASED LIGHTS FOR YOUR WALLBED YOU MUST STOP RETURN TO THE LIGHT KIT INSTRUCTIONS STEP 6 AND INSTALL THE SAFETY CUT OFF DEVICE BEFORE MOVING ON. WARNING: There is tremendous force involved in the next step, do not place hands be- tween the front of the side boards and the tension arms as you set the mechanism.
- Page 18 Step 22: Insert a 5/16” x 1” Hex Head bolt through hole #2 and tighten a 5/16” Nylock nut onto the bolt. Now tighten the nut and bolt in hole #3. Repeat step 22 on the other side of the bed unit.
- Page 19 Illustration 12 Step 24: When the bed is closed check to see if the gap on either side is the same. If it looks right skip this step. If the gap is not right, meaning that the Bed Box is too close to the side board or even touching it at the top on one side it will need to be adjusted.
Need help?
Do you have a question about the PARK CITY and is the answer not in the manual?
Questions and answers