Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for FAAC MASTER-B
Summary of Contents for FAAC MASTER-B
- Page 1 MASTER-B & MASTER-B & SLAVE-B SLAVE-B...
-
Page 2: Ec Declaration Of Conformity For Machines
FAAC are used. 6) FAAC declines all liability caused by improper use or use other than that for which the automated system was intended. 19) For maintenance, strictly use original parts by FAAC. - Page 3 It is not a back-up battery. The battery is recharged by the MASTER-B or SLAVE-B control board to which it is connected via the transformer and a specific integrated circuit. Bear in mind that it takes about 10 to 20 minutes of recharging to recover the energy used during an opening/closing cycle (this value varies according to operating ambient temperature, battery life and type of system).
-
Page 4: Description And Technical Specifications
The SLAVE-B equipment (required on 2-leaf gates only) is controlled by the MASTER-B equipment to which all accessories and pulse generators are connected. The MASTER-B board can be programmed and is used to set the following: function logics, work times (by self-learning) and pause times, leaf speed, and the sensitivity of the anti-crushing device. - Page 5 DESCRIPTION OF SYSTEM - ELECTRICAL 12 Vdc flashing lamp EQUIPMENT (standard system) Receiver Key operated push-button SLAVE-B MASTER-B control board control board Left-hand Right-hand DOMO DOMO operator operator Differential Tx photocell Rx Photocell thermal breaker Fig. 3 3 x 0.5 2 x 0.75...
- Page 6 The MASTER-B board positioning has to be decided before installing the control board enclosures since all accessories will be connected to this board. The MASTER-B board can be fitted either on the right or on the left side of the gate. You only have to decide to which leaf it will be associated as shown in Fig. 5.
- Page 7 (optional) 12V battery Fig. 7 Note: if not using the transformer supplied by FAAC, make sure that the secondary winding is 12Vac - 16VA. SLAVE-B BOARD LAYOUT MASTER-B BOARD LAYOUT J1, J5, P1, P2 and LED are not present on the SLAVE-B board, Programming push-button: "Function"...
-
Page 8: Electrical Connections
FSW OP (Opening safety devices contact) Photocells (e.g. SAFEBEAM) FSW CL (Closing safety devices contact) Photocells (e.g. SAFEBEAM) (MASTER-B - SLAVE-B connection) 7 - 8 (positive for 24V power supply) Accessories MAX total absorption of 150mA 9 - 11 W.L. - Page 9 Opening safety devices Fig. 9 Fig. 11 Attention : a maximum of 2 pairs of SAFEBEAM photocells can be connected to the MASTER-B board Examples of photocell connections 1 pair of CLOSING connection of no devices 1 pair of OPENING photocells...
- Page 10 • The status of LEDs with the gate closed at rest is shown in Steady light Mains power present and battery charged. bold. • LED 1 is active only when the MASTER-B and SLAVE-B boards communicate in systems with double-leaf gates and with Slow flashing Mains power not supplied for not more the SLAVE-B battery charged.
- Page 11 12.4.1 Leaf 1 management with MASTER-B or SLAVE- 12.4.3 Pause Times B board In all LEDs OFF status, press and Press push-button P1 again and hold down push-button P1, and LED B will light together with LED 1. press push-button P2 - LED A begins to flash.
- Page 12 If you press push-button P2 for 1 second, mechanical stop-points, give the stop the MASTER-B leaf and the SLAVE-B command at the required point with a leaf will begin to move together until further pulse from P2.
-
Page 13: Maintenance
12.5 Status of indicator light If you wish to use a 12V-0.5W indicator light (terminal 9 - 11 of J1, see Fig. 8), the following table shows the statuses of the indicator light according to gate position. Tab. 4 - Statuses of indicator light Indicator-light status Gate status Light Off... -
Page 15: Troubleshooting
SLAVE-B battery discharged. Allow the SLAVE-B battery to recharge (The SLAVE-B board LED flashes rapidly until the LED is on steady light. and LED 1 of the MASTER-B board on the inputs status is OFF). Automated system shut down. Discharged batteries Check if LED P of the MASTER-B board is OFF or flashing rapidly. - Page 16 Le descrizioni e le illustrazioni del presente manuale non sono impegnative. La FAAC si riserva il diritto, lasciando inalterate le caratteristiche essenziali dell’apparecchiatura, di apportare in qualunque momento e senza impegnarsi ad aggiornare la presente pubblicazione, le modifiche che essa ritiene convenienti per miglioramenti tecnici o per qualsiasi altra esigenza di carattere costruttivo o commerciale.