Siemens SINAMICS G120C Getting Started page 39

P-No. Note
r2093 BO: PROFIdrive PZD4 receive bit-serial
r2094 BO: Connector-binector converter binector output
r2095 BO: Connector-binector converter binector output
p2100 Setting the fault number for fault response
p2101 Setting the fault response
0 None
2 OFF2
5 STOP2
p2103 BI: 1. Acknowledge faults
p2104 BI: 2. Acknowledge faults
p2106 BI: External fault 1
r2110 Alarm number
p2111 Alarm counter
p2112 BI: External alarm 1
r2122 Alarm code
r2123 Alarm time received [ms]
r2124 Alarm value
r2125 Alarm time removed [ms]
p2126 Setting fault number for acknowledge mode
p2127 Sets acknowledgement mode
p2128 Selecting fault/alarm code for trigger
r2129 CO/BO: Trigger word for faults and alarms
r2130 Fault time received in days
r2133 Fault value for float values
r2134 Alarm value for float values
r2135 CO/BO: Status word, faults/alarms 2
r2136 Fault time removed in days
r2138 CO/BO: Control word, faults/alarms
r2139 CO/BO: Status word, faults/alarms 1
r2169 CO: Actual speed smoothed signals
r2197 CO/BO: Status word monitoring functions 1
r2198 CO/BO: Status word monitoring 2
r2199 CO/BO: Status word monitoring 3
p2200 BI: Technology controller enable
p2201 CO: Techn. controller fixed value 1 [100 ≙ 100%]
p2202 CO: Techn. controller fixed value 2 [100 ≙ 100%]
p2203 CO: Techn. controller fixed value 3 [100 ≙ 100%]
p2204 CO: Techn. controller fixed value 4 [100 ≙ 100%]
SINAMICS G120C frequency converter
Getting Started, 03/2012, FW V4.5, A5E03831830B AA
1 OFF1
3 OFF3
6 DC braking
P-No. Note
p2205 CO: Techn. controller fixed value 5 [100 ≙ 100%]
p2206 CO: Techn. controller fixed value 6 [100 ≙ 100%]
p2207 CO: Techn. controller fixed value 7 [100 ≙ 100%]
p2208 CO: Techn. controller fixed value 8 [100 ≙ 100%]
p2209 CO: Techn. controller fixed value 9 [100 ≙ 100%]
p2210 CO: Techn. controller fixed value 10 [100 ≙
100%]
p2211 CO: Techn. controller fixed value 11 [100 ≙
100%]
p2212 CO: Techn. controller fixed value 12 [100 ≙
100%]
p2213 CO: Techn. controller fixed value 13 [100 ≙
100%]
p2214 CO: Techn. controller fixed value 14 [100 ≙
100%]
p2215 CO: Techn. controller fixed value 15 [100 ≙
100%]
p2216 Techn. controller fixed value selection method
0 Fixed value selection direct
1 Fixed value selection binary
p2220 BI: Techn. controller fixed value selection bit 0
p2221 BI: Techn. controller fixed value selection bit 1
p2222 BI: Techn. controller fixed value selection bit 2
p2223 BI: Techn. controller fixed value selection bit 3
r2224 CO: Techn. controller fixed value active [100 ≙
100%]
r2225 CO/BO: Techn. controller fixed value selection
status word
r2229 Techn. controller number currently
p2230 Techn. controller motorized potentiometer
configuration
.00 Storage active
.02 Initial rounding active
.03 Non-volatile data save active for
p2230.0 = 1
.04 Ramp-function generator always active
r2231 Techn. controller motorized potentiometer
setpoint memory
p2235 BI: Techn. controller motorized potentiometer
setpoint up
p2236 BI: Techn. controller motorized potentiometer
setpoint down
p2237 Techn. controller motorized potentiometer
maximum value [%]
p2238 Techn. controller motorized potentiometer
minimum value [%]
Commissioning
4.2 Further settings
37