Siemens SINAMICS G120C Getting Started page 31

P-No. Note
p0323 Maximum motor current [A]
r0330 Rated motor slip
r0331 Actual motor magnetizing current/short-circuit
current
r0333 Rated motor torque [Nm]
p0335 Motor cooling type
p0340 Automatic calculation of motor/control parameters
p0341 Motor moment of inertia [kgm²]
p0342 Ratio between the total and motor moment of
inertia [kgm²]
r0345 Nominal motor starting time
p0346 Motor excitation build-up time [s]
p0347 Motor de-excitation time [s]
p0350 Motor stator resistance, cold [Ω]
p0352 Cable resistance [Ω]
r0395 Actual stator resistance
r0396 Actual rotor resistance
p0500 Technology application
p0505 Selecting the system of units
1 System of units SI
2 Referred system of units/SI
3 US system of units
4 System of units, referred/US
p0573 Inhibit automatic reference value calculation
p0595 Selecting technological units
1 %
3 bar
6 ltr/s
9 m³/min
12 kg/s
15 t/min
18 kN
21 °F
24 gallon/min
27 inch³/h
30 lb/h
33 K
36 m/s
39 BTU/min
42 inch wg
45 % r.h.
SINAMICS G120C frequency converter
Getting Started, 03/2012, FW V4.5, A5E03831830B AA
2 1 referred, no dimensions
4 °C 5 Pa
7 m³/s 8 ltr/min
10 ltr/h 11 m³/h
13 kg/min 14 kg/h
16 t/h 17 N
19 Nm 20 psi
22 gallon/s 23 inch³/s
25 inch³/min 26 gallon/h
28 lb/s 29 lb/min
31 lbf 32 lbf ft
34 rpm 35 parts/min
37 ft³/s 38 ft³/min
40 BTU/h 41 mbar
43 ft wg 44 m wg
46 g/kg
P-No. Note
p0596 Reference quantity, technological units
p0601 Motor temperature sensor type
0 No sensor
1 PTC warning & timer
2 KTY84
4 Bimetallic NC contact warning & timer
p0604 Motor temperature alarm threshold [°C]
p0605 Motor temperature fault threshold [°C]
p0610 Motor overtemperature response
0 No response, alarm only, no reduction of I
1 Alarm with reduction of I
2 Alarm and fault, no reduction of I
p0611 I2t motor model thermal time constant [s]
p0615 I2t motor model fault threshold [°C]
p0625 Motor ambient temperature [°C]
p0637 Q flux, flux gradient saturated [mH]
p0640 Current limit [A]
p0700 Command source selection
r0720 CU number of inputs and outputs
r0722 CO/BO: CU digital inputs, status
.00 DI 0 (terminal 5)
.01 DI 1 (terminal 6)
.02 DI 2 (terminal 7)
.03 DI 3 (terminal 8)
.04 DI 4 (terminal 16)
.05 DI 5 (terminal 17)
.11 DI 11 (terminals 3, 4) AI 0
r0723 CO/BO: CU digital inputs, status inverted
p0730 BI: CU signal source for terminal DO 0
NO: Terminal 19 / NC: Terminal 18
p0731 BI: CU signal source for terminal DO 1
NO: Terminal 21
r0747 CU, digital outputs status
p0748 CU, invert digital outputs
r0751 BO: CU analog inputs status word
r0752 CO: CU analog inputs input voltage/current actual
AI0 (terminals 3/4)
Commissioning
4.2 Further settings
max
and fault
max
max
29