Siemens SINAMICS G120C Getting Started page 30

Commissioning
4.2 Further settings
P-No. Note
r0060 CO: Speed setpoint before setpoint filter
[100 % ≙ p2000]
r0062 CO: Speed setpoint after filter [100 % ≙ p2000]
r0063 CO: Speed actual value unsmoothed
[100 % ≙ p2000]
r0064 CO: Speed controller system deviation
[100 % ≙ p2000]
r0065 Slip frequency [100 % ≙ p2000]
r0066 CO: Output frequency [100 % ≙ p2000]
r0067 CO: Output current, maximum [100 % ≙ p2002]
r0068 CO: Absolute current actual value unsmoothed
[100 % ≙ p2002]
r0070 CO: Actual DC link voltage [100 % ≙ p2001]
r0071 Maximum output voltage [100 % ≙ p2001]
r0072 CO: Output voltage [100 % ≙ p2001]
r0075 CO: Current setpoint field-generating
[100 % ≙ p2002]
r0076 CO: Current actual value field-generating
[100 % ≙ p2002]
r0077 CO: Current setpoint torque-generating
[100 % ≙ p2002]
r0078 CO: Current actual value torque-generating
[100 % ≙ p2002]
r0079 CO: Torque setpoint, total [100 % ≙ p2003]
p0100 IEC/NEMA motor standard
0 IEC motor (50 Hz, SI units)
1 NEMA motor (60 Hz, US units)
2 NEMA motor (60 Hz, SI units)
P0124 CU Identification via LED
p0170 Number of Command Data Sets (CDS)
p0180 Number of Drive Data Sets (DDS)
p0201 Power unit code number
r0204 Power unit, hardware properties
p0205 Power unit application
0 Load cycle with high overload
1 Load cycle with light overload
r0206 Rated power unit power [kw/hp]
r0207 Rated power unit current
r0208 Rated power unit line supply voltage [V]
r0209 Power unit, maximum current
28
P-No. Note
p0210 Drive unit line supply voltage [V]
p0230 Drive filter type, motor side
0 No filter
1 Motor reactor
2 dv/dt filter
3 Siemens sine-wave filter
4 Sine wave filter, third-party manufacturer
p0233 Power unit motor reactor [mH]
p0234 Power unit sine-wave filter capacitance [µF]
r0238 Internal power unit resistance
p0278 DC link voltage undervoltage threshold reduction
[V]
p0287 Ground fault monitoring thresholds
[100 % ≙ r0209]
r0289 CO: Maximum power unit output current
[100 % ≙ p2002]
p0290 Power unit overload response
0 Reduce output current or output frequency
1 No reduction, shutdown when overload
threshold is reached
2 Reduce I_output or f_output and f_pulse (not
using I2t).
3 Reduce the pulse frequency (not using I2t)
p0292 Power unit temperature alarm threshold [°C]
p0295 Fan run-on time [s]
p0300 Motor type selection
0 No motor
1 Induction motor
2 Synchronous motor
17 1LA7 standard induction motor
p0301 Motor code number selection
p0304 Rated motor voltage [V]
p0305 Rated motor current [A]
p0306 Number of motors connected in parallel
p0307 Rated motor power [kW]
p0308 Rated motor power factor
p0309 Rated motor efficiency [%]
p0310 Rated motor frequency [Hz]
p0311 Rated motor speed [rpm]
p0320 Motor rated magnetizing current/short-circuit
current [A]
p0322 Maximum motor speed [rpm]
Getting Started, 03/2012, FW V4.5, A5E03831830B AA
SINAMICS G120C frequency converter