Siemens SINAMICS G120C Getting Started page 34

Commissioning
4.2 Further settings
P-No. Note
p1037 Motorized potentiometer maximum speed [rpm]
p1038 Motorized potentiometer minimum speed [rpm]
p1040 Motorized potentiometer start value [rpm]
p1043 BI: Motorized potentiometer, accept setting value
p1044 CI: Motorized potentiometer setting value [100 %
≙ p2000]
r1045 CO: Motorized potentiometer, setpoint in front of
the ramp-function generator [rpm]
p1047 Motorized potentiometer ramp-up time [s]
p1048 Motorized potentiometer ramp-down time [s]
r1050 CO: Motorized potentiometer setpoint after the
ramp-function generator [100 % ≙ p2000]
p1055 BI: Jog bit 0
p1056 BI: Jog bit 1
p1058 Jog 1 speed setpoint [rpm]
p1059 Jog 2 speed setpoint [rpm]
p1070 CI: Main setpoint [100 % ≙ p2000]
p1071 CI: Main setpoint scaling [100 ≙ 100%]
r1073 CO: Main setpoint effective [100 % ≙ p2000]
p1075 CI: Supplementary setpoint [100 % ≙ p2000]
p1076 CI: Supplementary setpoint scaling [100 ≙ 100%]
r1077 CO: Supplementary setpoint effective
[100 % ≙ p2000]
r1078 CO: Total setpoint effective [100 % ≙ p2000]
p1080 Minimum speed [rpm]
p1082 Maximum speed [rpm]
p1083 CO:Speed limit in positive direction of rotation
[rpm]
r1084 CO: Speed limit positive effective [100 % ≙
p2000]
p1086 CO: Speed limit in negative direction of rotation
[rpm]
r1087 CO: Speed limit negative effective [100 % ≙
p2000]
p1091 Skip speed 1 [rpm]
p1092 Skip speed 2 [rpm]
p1101 Skip speed bandwidth [rpm]
p1110 BI: Inhibit negative direction
p1111 BI: Inhibit positive direction
p1113 BI: Setpoint inversion
r1114 CO: Setpoint after the direction limiting [100 % ≙
p2000]
r1119 CO: Ramp-function generator setpoint at the input
[100 % ≙ p2000]
32
P-No. Note
p1120 Ramp-function generator ramp-up time [s]
p1121 Ramp-function generator ramp-down time [s]
p1130 Ramp-function generator initial rounding-off time
[s]
p1131 Ramp-function generator final rounding-off time
[s]
p1134 Ramp-function generator rounding-off type
0 Continuous smoothing
1 Discontinuous smoothing
p1135 OFF3 ramp-down time [s]
p1136 OFF3 initial rounding-off time [s]
p1137 OFF3 final rounding-off time [s]
p1138 CI: Acceleration ramp scaling [100 ≙ 100%]
p1139 CI: Deceleration ramp scaling [100 ≙ 100%]
p1140 BI: Enable ramp-function generator
p1141 BI: Continue ramp-function generator
p1142 BI: Enable speed setpoint
r1149 CO: Ramp-function generator acceleration
[100 % ≙ p2007]
r1170 CO: Speed controller setpoint sum
[100 % ≙ p2000]
r1198 CO/BO: Control word, setpoint channel
p1200 Flying restart operating mode
0 Flying restart inactive
1 Flying restart always active (start in setpoint
direction)
4 Flying restart always active (start only in
setpoint direction)
p1201 BI: Flying restart enable signal source
p1202 Flying restart search current [100 % ≙ r0331]
p1203 Flying restart search rate factor [%]
A higher value results in a longer search time.
p1206 Set fault number without automatic restart
p1210 Automatic restart mode
Getting Started, 03/2012, FW V4.5, A5E03831830B AA
SINAMICS G120C frequency converter