Advertisement
UV Panel HP™
Please carefully read and understand the instructions in this manual
thoroughly before attempting to operate this unit. These instructions
contain important safety information regarding the use and mainte-
nance of this unit. Please keep this manual with the unit, for future
reference.
UV Panel HP™
Power Supply:
Before plugging your unit in, be sure the source
voltage in your area matches the required voltage for your American
DJ
UV Panel HP™ before attempting operation.
®
General Operation:
This fixture is designed to operate as a stand
alone unit. It has been tested and the lamp has been installed at the
factory there is no assembly necessary. The UV Panel HP™ is ready
to be plugged in, out of the box. "Flip" the power switch to the "on"
position and the lamp will immediately begin to glow.
UV Panel HP™
Fixture Cleaning:
Due to fog residue, smoke, and dust cleaning the
internal and external lenses should be carried out periodically to opti-
mize light output. Cleaning frequency depends on the environment
in which the fixture operates (I.e. smoke, fog residue, dust, dew).
In heavy use we recommend cleaning on a monthly basis. Periodic
cleaning will ensure longevity, and crisp beam output.
1. Use normal glass cleaner and a soft cloth to wipe down the out-
side casing.
2. Use a soft brush to clean out the air vents
3. Clean the external optics with glass cleaner and a soft cloth every
20 days.
4. Clean the internal optics with glass cleaner and a soft cloth every
30-60 days.
5. Always be sure to dry all parts completely before plugging the unit
back in.
American DJ
- www.americandj.com - UV Panel HP™ Instruction Manual Page 5
©
®
General Instructions
Operation
Cleaning
UV Panel HP™
Caution:
Always replace with the exact same type lamp and fuse,
unless otherwise specified by an authorized American DJ
cian. Replace with anything other than the specified part can damage
your unit and will void your manufactures warranty.
Warning:
If you continue to blow either the lamp or fuse after either
one has already been replaced, STOP using the unit. Contact cus-
tomer support for further instructions, you may have to return the unit
for servicing. Continuing to use the unit may cause serious damage.
Fuse Replacement: The fuse is located at the top rear of the unit next
to the power cord and power switch. Occasionally this fuse may blow
when the unit becomes to hot. To replace the fuse; disconnect the unit
from the main power supply and unscrew the fuse holder from the fuse
holder housing. Remove the old fuse and discard it, replace the fuse
with an exact same type. Insert the new fuse into it's holder and return
the holder to the fuse housing.
Lamp Replacement:
Caution! Never open the unit when in use.
Always disconnect the main power and allow the fixture ample time
to cool before attempting to replace the lamp. Lamp replacement has
been made simple by incorporating a remove tray that is retained by
a single thumb screws. Again, please remember to always replace
with the exact same type lamp. Please see the pictures on next page
for reference in this process.
1. Be sure to follow the proper procedures when handling UV lamps.
2. Locate the thumb screw that secures the plexi-glass lid. Remove
the thumb screw to access the lamps (Figure 1).
3. Once the screw has been removed, pull down the lid to expose
the lamps (Figure 2).
4. Remove the lamp by grabing the top of the lamp (Figures 3 and
4) pulling it gently down and out of its socket (Figure 5). The lamp
should then be pulled forward (towards you) and up (Figures 6, 7,
and 8).
5. Relplace the lamp with the same type of lamp. The lamp must
be inserted through the plastic holder first, and then into the
socket. Please, be very careful when doing this.
6. Close the lid and screw the thumb screw back into place to lock
the lid.
American DJ
- www.americandj.com - UV Panel HP™ Instruction Manual Page 6
©
®
Lamp and Fuse Replacement
techni-
®
Advertisement
