Programming Of Functioncodes - Hengstler tico 732 User Manual

2.2 Programming of function codes
Programming mode:
press while
switching
Power on
function
basic settings
count mode
decimal point
(on display)
reset/setmode
signal time
output 1
signal time
output 2
Output with
reset
pnp/npn-
selection
input
attentuation
dyn./static
Reset
output
signal memory
additional
totalizer
keylock for
reset key 6+4
keylock
for preset 1
keylock
for preset 2
keylock
for prescaler
keylock mode
(F20-F23)
* default values
1
bidirectional counting with single evaluation (eg. for encoders with 2 channels A,B)
2 parameter only appears for preset version
3
with appliances with one preset only, this applies to preset 1 and output 1 (OUT 1)
4 Input B passive (0V at PNP or 24V at NPN or open)
Input B active (24V at PNP or 0V at NPN)
Sach-Nr. 2 732 017; Version 1310301WBI
Change parameter:
press
code alternatives/signification
F0 0* no function
1 all function codes are set to the default values (*-marked)
F1 Input A
0 * count Input
1 count Input
2 count Input
3 adding
4 adding
5 adding
6 channel A
7 channel A
F3 0* no decimal point
1 one decimal place (xxxxx.x)
2 two decimal places (xxxx.xx)
3 three decimal places (xxx.xxx)
F4 0* reset to „0", no autoreset
1 reset to „0", with autoreset when reaching preset 2
2 set to preset 2, no autoreset
3 set to preset 2, with autoreset when reaching „0"
2
F6 OFF no Output signal
On bistable Output signal (latching), will be deleted by Out 2
0,02 20 ms
0,05 50 ms
0,10* 100 ms
0,20 200 ms
0,50 500 ms
1,00 1 s
F7 2 see see above; signal time output 1
above
F9 0* Do not activate the main preset output (OUT 2)
1 Activate the main preset (OUT 2)
F10 0 npn with 8V level (negative)
1* pnp with 8V level (positive)
2 npn with TTL-level
3 pnp with TTL-level
F11 0 30 Hz attenuation (for contacts)
1 * no attentuation, 5 kHz (bidirectional counting: 2,5 kHz)
F12 0* static reset
1 dynamic reset (counting possible during reseting)
F14 0* after power fail, the signal times will not be restarted
1 after power fail, the signal times will be restarted
F15 0* disabled
1 enabled
F20 0* key reset is possible
1 key reset is not possible (or possible with delay see F29)
2
F21 0* access to preset 1 is possible
1 access to preset 1 is not possible (or delayed see F29)
2
F22 0* access to preset 2 is possible
1 access to preset 2 is not possible (or delayed see F29)
F23 0* access to prescaler is possible
1 access to prescaler is not possible (or delayed see F29)
F29 0* access to parameters from F20-F23 is possible after
holding the keys for more than 10 sec.
1 access to parameter is not possible
Count direction negative
Change to the next function:
press
Input B Input C
gate reset
4
direction(u/d) reset
direction(u/d) 4 gate
subtracting reset
subtracting gate
adding reset
1 1
channel B reset
1 channel B 1 gate
2+3
3 in case of reset
Count direction positive
Return to count mode:
press > 5 s e c
2+3
2+3
3
in case of Reset
7/28