Advanced Micro Controls Inc. 1700 Series User Manual page 34

Transducer Outline Drawings (continued)
HT-400: Anodized Aluminum Body, 1070 Carbon Steel Shaft, NEMA 4
4.00"
#10-32 UNF-2B. 0.50"
Four places, 90° apart on 2.50"
2.000"
(50.80)
( ) = Dimensions in millimeters
HT-20-(x): Anodized and Painted Aluminum Body, 1070 Carbon Steel Shaft, NEMA 4
(x) =
Number of shaft turns needed to complete one rotation of the internal
resolver.
3.000"
2.000"
1.000"
(25.40)
2.000"
(50.80)
4.375"
(111.13)
0.50" max.
(12.7)
Total Clearance of 3.5"
for removal of mating connector.
20 Gear Drive, Plymouth Ind. Park, Terryville, CT 06786
Tel: (860) 585-1254 Fax: (860) 584-1973
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
Dia. ± 0.01"
(101.6) (0.3)
min. depth.
(12.7)
B.C.
(63.5)
1/4-20 UNC-2B 0.50" min. depth.
(12.7)
Four places.
(15.867)
0.6247"
0.55"
(14.0)
0.6237"
(15.842)
2.000"
(50.80)
1.000"
(25.40)
KEYWAY
0.1885 (4.79) 0.106 (2.69)
X DEEP X 1.0
0.1895 (4.81) 0.108 (2.74)
1.000"
KEY
(25.40)
0.187
(4.75)
SQ. X 1.0
(25.4)
0.188
(4.78)
When re-installing plate, make sure the gasket is seated correctly and not pinched.
Figure 3.12 HT-400 Outline Drawing
(76.20)
(50.80)
0.500"
(12.70)
0.500"
(12.70)
1.000"
(25.40)
1.1815" (30.010)
1.1807"
(29.990)
0.6247" (15.867)
0.6237"
(15.842)
1/4 - 20 UNC-2B
0.50" min. depth.
(12.7)
Four places
KEYWAY
0.106
0.1885 (4.79)
X
0.1895 0.108
(4.81)
KEY
0.187
(4.75)
SQ. X 1.0
0.188 (4.78)
needed
(89)
MS3102E16S-1P Connector
Figure 3.13 HT-20-(x) and HTT-20-1 Outline Drawing
Chapter 3
6.41"
1.250"
(31.75)
(25.4)
4.27"
(108.5)
#8-32 Screws, 4 places. Remove to access resolver connections.
0.375"
(9.53)
0.150"
(3.81)
1.25"
(31.8)
(2.69)
DEEP X 1.0 (25.4)
(2.74)
(25.4)
1.175"
(29.85)
Installation
1" NPT Thread
(162)
1.60" Sq.
(40.6)
4.00" (101.60)
Painted Body
Anodized Flange
( ) = Dimensions in millimeters
3-7