Advanced Micro Controls Inc. 1700 Series User Manual page 30

Transducer Outline Drawings (continued)
HT-20: Anodized Aluminum Body, 1070 Steel Shaft, NEMA 13
2.500"
(63.50)
2.000"
(50.80)
1.000"
(25.40)
2.500" 2.000"
(63.50) (50.80)
0.250"
(6.35)
1/4-20 UNC-2B
0.50"
(12.7)
Eight places
HT-20S: Anodized Aluminum Body, 1070 Steel Shaft, NEMA 13
2.500"
MS3102E16S-1P
Connector
2.000"
1.000"
(25.40)
2.500" 2.000"
(63.5) (50.8)
0.250"
0.60"
Total clearance of 3.5"
for removal of mating connector.
HT-20K/L: Hard Coat Anodized Aluminum Body, 303 Stainless Steel Shaft, NEMA 4X
2.500"
(63.50)
2.000"
(50.80)
1.000"
(25.40)
2.500" 2.000"
(50.80)
(63.5)
0.250"
(6.35)
1/4-20 UNC-2B
0.50"
(12.7)
Eight places.
20 Gear Drive, Plymouth Ind. Park, Terryville, CT 06786
Tel: (860) 585-1254 Fax: (860) 584-1973
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
KEYWAY
0.1885(4.79) 0.106(2.69)
X DEEP X 1.0(25.4)
0.1895(4.81) 0.108(2.74)
KEY
0.187(4.75)
SQ. X 1.0(25.4)
0.188(4.78)
1.000"
(25.40)
1.1815" (30.010)
1.1807"
(29.990)
0.6247" (15.867)
0.6237"
(15.842)
0.250"
(6.35)
min. depth.
( ) = Dimensions in millimeters
Figure 3.2 HT-20 Outline Drawing
(63.50)
(50.80)
KEYWAY
0.1885(4.79) 0.106(2.69)
X
0.1895(4.81) 0.108(2.74)
KEY
0.187(4.75)
SQ. X 1.0(25.4)
0.188(4.78)
1.000"
(25.40)
1.1815" (30.010)
1.1807"
(29.990)
0.6247" (15.87)
0.6237"
(15.84)
(6.35)
0.250"
(6.35)
max.
(15.2)
needed
(89)
Figure 3.3 HT-20S Outline Drawing
HT-20K SUPPLIED WITH VITON SHAFT SEAL
HT-20L SUPPLIED WITH NITRILE SHAFT SEAL
KEYWAY
0.106(2.69)
0.1885(4.79)
X DEEP X 1.0(25.4)
0.1895(4.81) 0.108(2.74)
KEY
0.187(4.75)
SQ. X 1.0(25.4)
0.188(4.78)
1.000"
(25.4)
0.6247" (15.867)
0.6237"
(15.842)
0.250"
(6.35)
min. depth
( ) = Dimensions in millimeters
Figure 3.4 HT-20K/L Outline Drawing
Chapter 3
4.75"
(120.7)
0.750"
(19.05) 3.250"
(82.55)
MS3102E16S-1P
0.150"
(3.81)
Connector
1.25"
(31.8)
4.75"
0.750" (19.05) 3.250"
DEEP X 1.0(25.4)
0.150"
(3.81) 1/4-20 UNC-2B
0.50"
1.25"
Eight places
(31.8)
4.75"
(120.7)
0.750"
(19.05) 3.250"
(82.55)
MS3102E16S-1P
1.25"
Connector
(31.8)
Installation
0.500"
(12.70)
1.500"
(38.10)
0.700" max.
(17.78)
Total clearance of 3.5"
(89)
needed for removal of
mating connector
(120.7)
(82.55)
0.500"
(12.70)
1.500"
(38.10)
(12.7) min. depth.
( ) = Dimensions in millimeters
0.500"
(12.70)
1.500"
(38.1)
0.700" max.
(17.78)
Total clearance of 3.5"
(89)
needed for removal of
mating connector
3-3