Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for PR Lighting PR-8330
Summary of Contents for PR Lighting PR-8330
- Page 1 BLINDER 360 PR-8330 This product manual contains important information about the safe installation and use of this projector. Please read and follow these instructions carefully and keep this manual in a safe place for future reference. PR LIGHTING LTD. http://www.pr-light ing.com...
- Page 2 Any damage caused by improper use will not be assumed by the manufacturer and / or dealer. Note: For the products made by Guangzhou PR lighting Ltd, the warranty for the whole product is one year starting from the delivery date but the light source is not within the warranty.
-
Page 3: Safety And Warnings
1. SAFETY AND WARNINGS NOTE Before a projector’s installation, power-on, operation and maintenance, please carefully read the safety information hereinafter! The following safety signs are used in the user manual. User Electrical Protective High Warning Flames Goggles Manual shock Gloves Temperature When unpacking , check if there is transportation damage before using the projector. -
Page 4: Cleaning And Maintenance
electrical parts’ life will be shortened . There are safety cord holes at the bottom of the base of a projector. In view of safety, please run the safety ● cord supplied through the safety cord holes for safety support. Before any installation, maintenance and cleaning work, please ensure the projector is disconnected from ●... -
Page 5: Installation Rigging
3. APPEARANCE INSTALLATION RIGGING ● Before moving a projector, Please lock Pan and Tilt. Before moving a projector, Please lock Pan and Tilt. Take 1 clamps and 1 safety cords out from the package and mount 1 clamps on the underside of fixture with 2 retainers attached to each clamp. -
Page 6: Power Connection
WARNING: The projector MUST be lifted or carried by the HANDLES instead of clamps. ● .For safety the safety cord should afford 10 times the Projector’s weight. ● POWER CONNECTION ● Connect the power cord as follows: L (live) =brown E (earth) =yellow/green N (neutral) =blue Before power connection, please ensure the power supplied must match what the nameplate says. -
Page 7: Dmx Terminator
DMX TERMINATOR ● In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX terminator. This prevents electrical noise from disturbing and corrupting the DMX control signals. The DMX terminator is simply an XLR connector with a 120 (ohm) resistor connected across pins 2 and 3, which is then plugged into the output socket on the last projector in the chain. -
Page 8: Setup And Configuration
5. SETUP AND CONFIGURATION FRONT PANEL OPERATION ● Projector configuration can be set conveniently via push buttons and LCD screen. Launch the projector and press button ENTER for more than 5 seconds to unlock the panel, the LCD will show the function menu of the projector, each main menu has its submenus and each submenu has a specific function. -
Page 9: Master/Slave Mode
MASTER/SLAVE MODE ● Many projectors can run synchronously in the Master/Slave mode by linking them with each other. First, connect the first fixture’s DMX output to the second fixture’s DMX input using XLR-XLR control cable and then connect the second fixture’s DMX output to the third fixture’s DMX input, and so on until all projector are connected in this way. - Page 10 XLR First XLR Only Wireless Mode Wireless Only （Default： XLR First） Wireless First Wireless To XLR Slave Master/Slave （Default：SLAV） Master OffAfterDelay Display Mode （Default： On Always offafterDelay） Display Reverse （Default：Off） English Language （Default：Egnlish） Chinese Sound Level 1～100 DisplayContrast 0-31 Pan amend 1-127 Tilt amend 1-127...
- Page 11 （Default：360） Power On Hours XXXX MainBoard X.X.X Software Version Pan&Tilt X.X.X Driver 1 X.X.X Head Sensor Display Board Temperature Pan and Tilt Information Driver Board 1 View DMX Values Channel XXX=XXX Electronic SN SN=XXXXXXXXXXXX RDM Device Lable Version X.X X Optocoupler Ok/Er Y Optocoupler Ok/Er Positions Sensor X Hall...
- Page 12 0-255 Area 12 0-255 Area 34 0-255 Area 56 0-255 Area 78 0-255 Pan Location 0-255 0-255 CH9 Titl Location 0-255 CH10 Titl 0-255 CH11 X&Y Speed 0-255 CH12 KeepTime 0-255 X*40mS Old PW High Old PW Mid Old PW Low New PW High Password Manage New PW Mid...
-
Page 13: Dmx Protocol
7. DMX PROTOCOL Standard Extended Function DMX Value Description Mode Mode Strobe 001-129 Pulse Strobe from slow to fast 130-255 Strobe from slow to fast Dimmer 000-255 Linear dimmer from dark to bright Dimmer Fine 000-255 Dimmer in 16 bit 001-031 All LED lamps on Effect1 from bright to dark with the speed from slow to... -
Page 14: Led Indication
8. LED INDICATION Descriptions of the signs on the top right of the screen Slave Master DMX512 Mode Preset Memory Sound Mode User Memory Test Mode It means the keys are locked. The keys are unlocked and the lock sign disappears after the Lock Sign ENTER key is pressed for more than 3s. - Page 15 Bi-directional and continual rotation for the front lens panel CONTROL International standard DMX512 signal, 3 pin and 5 pin interfaces Standard mode 12 channels, extended mode 20 channels Master/Slave mode Stand alone mode, preset memory, self mode, single scene OTHER FUNCTIONS Wireless control (Optional) Adjustable Pan &...
-
Page 16: Light Output
LIGHT OUTPUT: 2200 830 DISTANCE (m) DIAMETER (m) 17.3 34.6 16/20... -
Page 17: Circuit Diagram And Pcb Connections
10. CIRCUIT DIAGRAM AND PCB CONNECTIONS CIRCUIT DIAGRAM ● 17/20... -
Page 18: Pcb Connections
PCB CONNECTIONS ● LED lamp Board of PR-8330 Thermal sensor LED connector1： Area1~2 LED connector 2：Area LED connector 3：Area LED connector 4：Area LED Driver board of PR-8330 Power supply 24V LED connector1：Area1~2 LED connector 2：Area 3~4 LED connector 3：Area 5~6 LED connector 4：Area 7~8... -
Page 19: Component Order Codes
11. COMPONENT ORDER CODES NAME PART NO. QUANTITY REMARK POWER SUPPLY 192010140 LED LAMP BOARD OF PR-8330 230060656 CT 3000K 230060657 LED LAMP BOARD OF PR-8330 CT 6500K FUSE 270041037 PAN AND TILT BELTS 290151413 8025 FAN 030060104 TOUGHENED GLASS OF PR-8330... - Page 20 PR LIGHTING LTD. 1582 Xingye Avenue, Nancun Panyu Guangzhou, 511442 China TEL: +86-20-3995 2888 FAX: +86-20-3995 2330 P/N: P/N: 320020*** Version: (Preliminary） 20/20...
Need help?
Do you have a question about the PR-8330 and is the answer not in the manual?
Questions and answers