Adjustable Agitation Valve; Function; Assembly; Operating - Hardi Commander Plus SPC Series Instruction Book

Description Description
Description Description Description
This new Adjustable Agitation Valve replaces the
existing agitation valve at your Hardi Manifold System.
It gives you the possibility to continiously adjust the
quantity of liquid that is used for agitation or by-pass.

Function

Function
Function Function Function
The Adjustable Agitation Valve replaces the existing
agitation valve, and should be located at the same place
in the Hardi Manifold System
Diagram shows where the replacement takes place.
The green pressure valve has 4 positions. Two positions
are for “Agitation” and “Without Agitation” (by-pass). The
other two are marked “0” indicating the valve is closed.
With the new Adjustable Agitation Valve it is possible
to combine these positions continously. For example if
you want to spray with a high volume rate at high(-er)
pressure and want agitation in same time. This situation
could be impossible with the standard valve.
Dia Dia Dia Diag g g g g r r r r r am - Con Dia am - Conv v v v v entional liquid sy am - Con am - Con am - Con entional liquid sy entional liquid sy entional liquid sy entional liquid system
(Section - see complete diagram in your instruction book).
Assemb Assembly ly ly ly ly Assemb
Assemb Assemb
Lubrica Lubrica te all O-rings bef te all O-rings bef
Lubrica Lubricate all O-rings bef Lubrica te all O-rings bef te all O-rings befor
1. Remove cover behind MANIFOLD SYSTEM (platform
side).
2. Release cramps and remove hoses from the sides of
the existing valve.
3. Remove the existing valve by releasing the cramp
from the T-piece and unscrew the valve from the
bracket.
4. Fit the new agitation valve in the bracket and tighten
the union nut.
5. Mount cramp to T-piece.
6. Mount the hoses in the sides of the new Adjustable
Agitation Valve.
7. Put the cover back.

Adjustable Agitation Valve

stem stem stem stem
or ore assemb or or e assemb e assembly ly ly ly ly. . . . . e assemb
e assemb
Opera a a a a ting Oper Oper ting ting
Oper Oper ting ting
MANIFOLD SYSTEM MANIFOLD SY MANIFOLD SY MANIFOLD SY MANIFOLD SY STEM STEM STEM STEM
See instruction book for information about selecting
optional equipment
Adjustab b b b b le Agita Adjusta Adjusta le Agita le Agitation V le Agita
Adjusta Adjusta le Agita
The valve is marked with arrows on the green disc that
indicates the amount of liquid that passes through the
valve. If handle is turned to a position near the tip of the
arrow, then only a small amount of liquid is allowed to
pass the valve. Otherwise, if handle is turned to a
position in the wide end of the arrow, it means that a
larger amount is passing the valve.
Now you have the posibility to continously adjust how
large amount of fluid from the pump is used for agitation
in the tank and for spraying.
Examples on handle positions at different agitation
quantities:
1. Handle is in same
position as (open)
agitation position at
the original valve.
Agitation quantity is
100%.
2. Handle is positioned
at the middle of the
arrow (in agitation
side of the disk).
Agitation quantity is
50%.
3. Handle is positioned
near the tip of the arrow
(in agitation side of the
disk). Agitation quantity
is 10%.

By-pass

By-pass By-pass By-pass By-pass
When using agitation and you want to turn it off, then
turn the handle 180 degree around. This means that
agitation is off but the spraying pressure remains the
same - opposite to closing the valve, which will increase
the pressure.
GB 08 06
tion Valv tion V tion V alve e e e e alv alv
tion V alv
T020-0047
T020-0046
T020-0048
45