Subscribe to Our Youtube Channel
Related Manuals for SEA USER 1 24V DG MAXI
Summary of Contents for SEA USER 1 24V DG MAXI
- Page 1 International registered trademark n. 804888 USER 1 24V DG MAXI S.p.A. ona Ind striale Sant Atto eramo I A elephone .seateam.com seacom seateam.com 4112 1 REV. 1 /2 1...
- Page 2 E G IS taliano International registered trademark n. 804888 1 - COMPONENTS EA URES o er s ppl A sorption in stand 30 mA perator ma . c rrent 20 A En ironment temperat re -20 C +50 C E ternal o 305 x 225 x 125 mm - IP55 -------- --------...
- Page 3 E G IS taliano International registered trademark n. 804888 2 - CONNECTIONS * 24V (red) Closing Limit Switch (yellow) Opening Limit Switch (green) Common (white) Closing Limit Switch (yellow) Opening Limit Switch (green) Ma . 1 Ma . 4 24V A ESS RIES RADI M DU E...
- Page 4 E G IS taliano International registered trademark n. 804888 4 - CONNECTIONS ON CN1 4.1 S AR n clamps 2 and The automation can be opened or closed through an impulse transmitted to this input (via e button, e board, etc.). To connect other Start devices (for ex.
- Page 5 E G IS taliano International registered trademark n. 804888 EXAMPLE OF AS I G IG CONNECTION n clamps 12 and 1 LAMP AND It warns of the gate movement b performing 1 blin per SECURITY EDGE second on opening, 2 blin s per second on closing and remaining on stead during pause.
- Page 6 E G IS taliano International registered trademark n. 804888 4.11 SA E EXAMPLE OF SAFETY LOOP CONNECTION Safet E it oop oop 1 Connection scheme of the 1 reader loop detector Photocell 1 contact Loop 1 Common Safety Exit Shado oop 2 Loop1 Connection scheme of the...
- Page 7 E G IS taliano International registered trademark n. 804888 EX ER A RE EIVER EXAMPLE OF EXTERNAL RECEIVER CONNECTION An external receiver can be connected to the control unit according to the connection diagram. For more details on connections and functionalities of the external receiver, refer to the relative instruction manual LATCH OPENING...
- Page 8 The first self-learning movement must alwa s be in closing. ou use the SEA magnetic limit switches, ma e sure that the menu 1 4 SE E IMI S I set on...
- Page 9 MA AGED To wor in Master/Slave it is necessar to use the code SEA 23001220) consisting of MAS ER/S AVE I two circuits: one to be connected to the control unit that will be set as MAS ER and one to be connected to the control unit that will be set as S AVE .
- Page 10 E G IS taliano International registered trademark n. 804888 MAS ER / S AVE SE RES E I S A A D SE CIRCUIT ON MASTER UNIT CIRCUIT ON SLAVE UNIT I DIVIDUA Note: The use of a shielded and twisted pairs transmission cable type RS482 with a section not exceeding 0.5 mm is recommended AR I G efore proceedin...
- Page 11 E G IS taliano International registered trademark n. 804888 7 - CONNECTIONS ON CN5 .1 DR MA AGEME E ample co rtes The CN5 connector can be used as a dr contact on which to connect li ht the 24 accessories through the use of an external power suppl (max. 1A and 30 ) according to the aside connection diagram closed on 1 and 2 open...
- Page 12 E G IS taliano International registered trademark n. 804888 8 - CONNECTIONS ON CN6 .1 M Motor 1 Motor 1 connection output Ma . 4 The drawing shows an external operator for sliding gate only as an exemple 9 - CONNECTIONS ON CN7 ERIES ARGER U I It is possible to power the control unit using t o 12V...
- Page 13 E G IS taliano International registered trademark n. 804888 10 - CONNECTIONS ON CN8 1 .1 ER SU TRANSFORMER EXAMPLE: OPERATOR SLIDING GATE 11 V o er S ppl Inp t NOTE: In case of unstable power supply the use of a power Power suppl connection input supply stabilized by min.
- Page 14 E G IS taliano International registered trademark n. 804888 12 - CONNECTIONS ON CNE 12.1 E The E DER on board can be connected on CNE through the special pre-wired cable. In case of non pre-wired Encoder use an appropriate adapter respecting the cable colors OLD TYPE ENCODER BRO N - HITE -...
- Page 15 E G IS taliano International registered trademark n. 804888 1 .2 AM ER ME RI MA AGEME The control unit is equipped with an obstacle detection s stem, which allows reversing in opening and closing If the obstacle detection s stem intervenes in opening, it causes a reverse of the motion for about 1 second If the obstacle detection s stem intervenes in closing, it causes the partial or total reopening of the gate depending on the settings on menu 4 SI G I VERSI...
- Page 16 E G IS taliano International registered trademark n. 804888 14 - PRELIMINARY AR I G Starting from the software revision 03.00, the electronic control unit is equipped with t e ne display with different D T C sym ols than the previous version. If ou have a control unit with the old ersion displa cons lt the man al of the pre io s re ision D DIS REVI US MA UA REVISI...
-
Page 17: Basic Menu Functions
E G IS taliano International registered trademark n. 804888 15 - BASIC MENU FUNCTIONS RESS M VE R UG E G IS A D RE UR A GUAGE MAI ME U DOWN Skip this step if no need Tx programming TO CONFIRM AND EXIT Press the TX RESS... - Page 18 Press UP to start programming The gate automaticall performs the c cle: Self learnin completed 1 .1 EAR I G R EDURE In SEA sliding operators the control unit is Power ON alread set b default on the respective 00000000...
-
Page 19: Operating Logics
E G IS taliano International registered trademark n. 804888 17 - OPERATING LOGICS RE IMI AR 1 For the automatic closing it is necessar to set a pause time through the men AUSE IME set a time between 1 second and 240 seconds. B default this parameter is OFF (semi-automatic logic) 2 It is possible to choose whether or not to accept the Start in pause on men S AR... -
Page 20: Password Management
E G IS taliano International registered trademark n. 804888 18 - PASSWORD MANAGEMENT B default the password is disabled. To set a password proceed as follows: o on an basic menu number Press UP and DO N simultaneousl for 5 seconds and access the Special Menu SP Scroll using the UP or DO N buttons to the 112 ASS RD men Press O... - Page 21 E G IS taliano International registered trademark n. 804888 19 - INPUT STATUS CHECK AND MANAGEMENT The input status chec menu is displa ed at the start of the control unit (for more details see chapter 14). Each input corresponds to a fixed position on the displa , according to the diagram below and can be .
- Page 22 E G IS taliano International registered trademark n. 804888 1 .2 USER 1 24V DG MAXI I U MA AGEME ME U Through this menu it is possible to activate or deactivate the inputs without repeating the self-learning LANGUAGE BACK TO THE...
- Page 23 E G IS taliano International registered trademark n. 804888 20 - RECEIVERS AND REMOTE CONTROLS R U I R U I G RE EIVERS RE EIVER MAX UM ER USERS UG I RE EIVERS 1 USERS ithout additional memor R U I USERS ith MEMO RF additional memor R U I G...
- Page 24 E G IS taliano International registered trademark n. 804888 2 .1 REM S R GRAMMI G AR I G The first stored radio transmitter will determine the coding of the following ones: if the first radio transmitter is stored as ROLLIN CODE, then all the following radio transmitters must be stored as ROLLIN CODE (FI CODE storing will not be accepted).
- Page 25 E G IS taliano International registered trademark n. 804888 S R GRAMMI G A PROGRAMMING PRESS THE BUTTON MENU TO BE STORED «START» COMMAND PRESS START STORED MUST ALWAYS BE LANGUAGE TRANSMITTERS BUTTON STORED ON THE TX PRESS THE BUTTON TO BE STORED PROGRAMMING OF PARTIAL...
- Page 26 USER 1 24V DG MAXI MENU FUNCTIONS TABLE MENU DESCRIPTION DEFAULT NOTE Italiano Italian English English 1 LANGUAGE Français French English Español Spanish Dutch Dutch Start Start Partial opening Partial opening External module External module Stop Stop Pressed once, it stops the gate. Pressed twice, it...
-
Page 27: Special Menu
PRESS AT THE SAME TIME FOR 5 SECONDS TO ENTER OR TO EXIT THE SPECIAL MENU USER 1 24V DG MAXI SPECIAL MENU FUNCTIONS TABLE For entering into the special menu move on one of the menu and press the UP and DOWN buttons at the same time for 5 sec. - Page 28 SP MENU DESCRIPTION DEFAULT NOTE OPENING SLOWDOWN OFF = Disabled 100% = the slowdown will Start at 100% middle of the total stroke CLOSING SLOWDOWN OFF = Disabled 100% = the slowdown will Start at 100% middle of the total stroke Adjust the passage between normal speed and slowdown 63 DECELERATION depends...
- Page 29 SP MENU DESCRIPTION DEFAULT NOTE Turn the selected input into one to which to connect an external clock 92 TIMER On photo2 Note: the "On partial entry" option is only visible with the 118-LATCH menu set to OFF On partial entry Always AUX output always Power supplied In cycle...
- Page 30 SP MENU DESCRIPTION DEFAULT NOTE If the photocell is occupied, it reverses the movement in Closing closing; during the pause, it prevents the reclosing If the photocell is activated during opening, the gate Stop and open stops and will continue in opening only when the photocell is released.
- Page 31 SP MENU DESCRIPTION DEFAULT NOTE Shows last event 106 DIAGNOSTICS - - - - (See alarms table) 107 MAINTENANCE CYCLES 100 240000 Setting from 100 to 240000 100000 Reports the executed cycles. Keep pressed OK to reset 108 PERFORMED CYCLES 240000 the cycles Note: "0000"...
- Page 32 E G IS taliano International registered trademark n. 804888 ALARMS The control unit advises about faults b a message on the displa . The table below shows which faults are advised and what to do in the event of a malfunction. However, it is possible to read the last 10 fault warnings b accessing the 1 DIAG S I menu...
-
Page 33: Troubleshooting
E G IS taliano International registered trademark n. 804888 TROUBLESHOOTING Ad ices Make sure all Safeties are turned ON Problem Found Possible Cause Solutions a) Check the connections or the jumpers on the connections of Operator doesn’t respond to a) Check the connected N.C. contacts the safety edge or of the stop and of the photocell if connected any START impulse b) Burnt fuse... - Page 34 E G IS taliano International registered trademark n. 804888 Ad ices Make sure all Safeties are turned ON Problem Found Possible Cause Solutions a) Check all Open inputs for an active input a) Open control active b) Check pause settings Gate opens, but will not close b) Pause not set c) Check all Entrapment Protection Device inputs for an active...
- Page 35 Materials handling must be made with appropriate vehicles ARRA IMI S - see the sales conditions SEA S.p.A. reserves the right to ma e any required modification or change to the products and/or to this manual without any advanced notice obligation...
- Page 36 Transport of the goods sold shall be at Bu er s cost and ris . SEA shall not bear the costs of deliver giving the goods to the carrier, as chosen either b SEA or b the Bu er. An loss and/or damage of the goods during transport, are at Bu er s cost.
- Page 37 5. Do not install the equipment in an explosive atmosphere. 6. SEA S.p.A. is not responsible for failure to observe ood Techniques in the construction of the loc ing elements to motorize, or for an deformation that ma occur during use.
- Page 38 La SEA S.p.A. dichiara sotto la propria responsabilità e, se applicabile, del suo rappresentante autorizzatoche il prodotto: SEA S.p.A. declares under its proper responsability and, if applicable, under the responsability of its authorised representative that the product: Descrizione / Description...
- Page 39 Cet article a t produit suivant des proc dures d usinage strictes et il a singulièrement t test afin de garantir les plus hauts niveaux de qualit pour votre satisfaction. Nous vous remercions d avoir choisi SEA. Este articulo ha sido producido siguiendo rigidos procedimientos de elaboracion...
- Page 40 International registered trademark n. 804888 SEA S.p.A. ona ind striale 4 2 S.A eramo 41 r.a. a .seateam.com seacom seateam.com...
Need help?
Do you have a question about the USER 1 24V DG MAXI and is the answer not in the manual?
Questions and answers