Related Manuals for Barco R9002240
Summary of Contents for Barco R9002240
-
Page 7: Safety Instructions
Part 15 of FCC rules and EN55022. projector. Record these numbers in the spaces provided below. Refer to them whenever you call upon your BARCO dealer regarding this * All the safety and operating instructions should be read before using product. - Page 8 Black: line (live) as the BARCO original part. Unauthorized substitutions may result in degraded performance and reliability, fire, electric shock or other hazards. Unauthorized substitutions may void warranty. 3. Do not allow anything to rest on the power cord.
- Page 12 14.5 cm green phosphor...
- Page 13 Lock screws...
- Page 15 SUHVVHG ADJUSTMENT MODE Select a path from below: GUIDED RANDOM ACCESS INSTALLATION SERVICE IRIS source 1 Select with then <ENTER> <EXIT> to return...
- Page 16 Select with then <ENTER> <EXIT> to return...
- Page 17 PASSWORD MODE POWER UP MODE PASSWORD REQUIRED OPERATING MODE WHEN FOR ADJUSTMENT POWER IS SWITCHED ON PLAYING StdBY BAUD RATE TABLE TO COMPUTER PROJECTOR ADDRESS StdBY (sum) CODE SPEED MAIN POWER PROCESSOR CYCLES I 2 C SHORTED BLOCK MATCH RESERVED ERROR 1200 POWER UP MODE...
- Page 18 Addressable with RCU Addressable with PC, MAC or workstation PROJECTOR ADDRESS...
- Page 19 Source 2 Fh= 15.6 kHz Fv= 50 Hz OFF ON...
- Page 20 OFF ON...
- Page 22 ART.NR : RXXXXXXX SER.NR ; RXXXXXXX 120V operation 230V operation 230V 2xT5A/250V 120V 2xT10A/250V...
- Page 25 &$Âu€ Composite video ‡‚Ãr‘‡Ãƒ…‚wrp‡‚…Â… ‡‚ÃhÀ‚v‡‚… TV tuner, e.g. TVDM40 stereo Audio amplifier...
- Page 26 QPSUÃ%à /XPD&KURPD QPSUÃ" &$Âu€Ã‡r …€...
- Page 27 QPSUÃ" , QWHUIDFH &$ u€Ã ‡r…€...
- Page 28 QPSUÃ%Ã VCR HDTV player Audio amplifier...
- Page 29 RISK OF ELECTRICAL SHOCK NO USER ADJUSTABLE PARTS INSIDE THE FOLLOWING INSTALLATION MENUS ARE RESERVED TO, AND TO BE PERFORMED ONLY BY BARCO PERSONNEL, OR BARCO AUTHORIZED DEALERS IF QUALIFIED, PRESS <ENTER> TO CONTINUE, OR IF NOT, <EXIT> TO RETURN. enter password...
-
Page 30: Optical Lens Focusing
FHLOLQJ SURMHFWRU VFUHHQ OPTICAL LENS FOCUSING 1. LOOSEN THE NUT ON THE REAR OF THE XXXX LENS, ROTATE THE LENS BARREL TO FOCUS THE CENTER OF THE IMAGE, THEN TIGHTEN THE NUT 2. LOOSEN THE NUT ON THE FRONT OF THE XXXX LENS AND ROTATE THE FRONT SECTION OF THE LENS TO FOCUS THE CORNERS OF THE... -
Page 31: Raster Centering
RASTER CENTERING CONTRAST LEVEL IS REDUCED AND BRIGHTNESS INCREASED TO MAKE THE RASTER VISIBLE ON THE FACE PLATE OF EACH CRT. USE THE ARROW KEYS TO CENTER THE RASTER ON THE GREEN, RED AND BLUE CRT RESPECTIVELY <ENTER> to continue <EXIT>... -
Page 32: Crt Projection Angle Adjustment
CRT PROJECTION ANGLE ADJUSTMENT CRT PROJECTION ANGLE IS THE FIRST STEP OF STATIC CONVERGENCE ADJUSTMENT. IT IS CRITICAL THAT THE RASTERS ARE CENTERED ON THE CRT FACE PLATES PRIOR TO PERFORMING THIS STEP. <ENTER> to read more <EXIT> to return CRT PROJECTION ANGLE ADJUSTMENT DURING THIS PROCEDURE,... - Page 33 PROJECTION ANGLE ADJUSTMENT Align crosshairs <ENTER> continue <EXIT> to return (SW1 > SW2)
- Page 34 DIAGONAL IMAGE FOCUSING 1. TURN THE SCREW MARKED Ã TO FOCUS THE IMAGE DIAGO- NALLY from LEFT (bottom) TO RIGHT (top). 2. TURN THE SCREW MARKED TO FOCUS THE IMAGE DIAGO- NALLY from LEFT (top) TO RIGHT (bottom) <ENTER> to continue <EXIT>...
- Page 35 LENS CORNER FOCUSING CENTER FOCUSING DIAGONAL IMAGE FOCUSING DIAGONAL IMAGE FOCUSING from left top to right bottom from left bottom to right top i ‚ y‡Ã6 % i ‚ y‡Ã6 i ‚ y‡Ã6 # i ‚ y‡Ã6 " i ‚ y‡Ã6 ! i ‚...
- Page 39 Use the potentiometers on the G2-ADJ. module to set the screen grid voltage for Red, Green and Blue. Adjust until the LED on the corresponding output amplifier is turned off. <EXIT> to return...
- Page 41 é ê ç è é ê ç è é ê...
- Page 42 é ê ç è é ê ç è é ê é ê ç è é ê ç è é ê...