Page 3
Changes Barco provides this manual ’as is’ without warranty of any kind, either expressed or implied, including but not limited to the implied war- ranties or merchantability and fitness for a particular purpose. Barco may make improvements and/or changes to the product(s) and/or the program(s) described in this publication at any time without notice.
Installation Instructions Before operating this equipment please read this manual thoroughly, and retain it for future reference. Installation and preliminary adjustments should be performed by qualified BARCO personnel or by authorized BARCO service dealers. Owner’s Record The part number and serial number are located at the back side of the projector. Record these numbers in the spaces provided below.
For this reason, it is absolutely necessary to leave an "exclusion zone" around all external surfaces of the projector whereby no flammable or combustible materials are present. The exclusion zone must be not less that 10 cm (4") for Barco Retro Projectors.
Page 11
If the product exhibits a distinct change in performance, indicating a need for service. • Replacement parts: When replacement parts are required, be sure the service technician has used original BARCO replace- ment parts or authorized replacement parts which have the same characteristics as the BARCO original part. Unauthorized substitutions may result in degraded performance and reliability, fire, electric shock or other hazards.
PROJECTOR MODE COMM. PORT Image 2-1 AC Power Cord Connection 2.2 AC Power Voltage What is the AC Power Voltage? The power input voltage is autoranging between 100V (-10%) and 240V (+6%). R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
Page 14
2. AC Power R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
1. Input signal : R, G and B with automatic sync detection between seperate sync (separate composite sync or with separate hor and vert. sync) or sync on green (composite sync). R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
Connect your RGB source with sync on green, composite or separate sync via an interface to Port 3. Always use an interface (e.g. Barco Magik Interface R9828120) when a computer and local monitor have to be connected to the projector as the signal cable coming from the computer is limited to 60 cm due to interferences.
Always use an interface (e.g. Barco Magik Interface R9828120) when a computer and local monitor have to be connected to the projector as the signal cable coming from the computer is limited to 60 cm due to interfer- ences.
The selected source number will be displayed on a 2 digit display and the selected input modules will be indicated with a LED on the rear. RCVDS 05 switcher Port on projector (R9827880) 800 periphals COMM. PORT Image 3-5 Connecting a RCVDS 05 switcher to the projector R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
"pause" (blanked picture, full power for immediate restarting) • direct access to all connected sources. 4.3 Terminology overview Overview The following table gives an overview of the different functionalities of the keys. R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
Page 20
15 min before adjusting the phase, press to adjust the phase of the projected image. FREEZ press to freeze the projected image. R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
Operational mode (Picture displayed). • Stand By mode. Starting up in Operational Mode The projector can start up with the selected source or the projector can start up with a warm up cycle message. R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
1. Use the same power switch to switch off the projector. 4.5 Using the RCU Pointing to the reflective screen 1. Point the front of the RCU to the screen surface. R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
TINT COLOR BRIGHTN CONTR TREBLE BALANCE BASS Image 4-4 RCU to IR sensors 4.6 Projector Address 4.6.1 Controlling the projector Projector address Address installed in the projector to be individually controlled. R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
When an image control is pressed, a text box with a bar scale, icon and function name of the control, e.g. ’brightness...’ appears on the screen (only if text is ON). See example screen. The length of the bar scale and the value of the numeric indication indicate the R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
Select a source number. The Freeze key (Only with optional Line Multiplier) When the Freeze key is pressed, the image is frozen until this key is pressed again (only with built in Line Multiplier). R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
Some items in the Adjustment Mode are password protected. While selecting such an item, the projector asks to enter your pass- word. Password Protection is only available when the password strap on the controller module is on. Contact a Barco authorized technician when no password is requested during the adjustment procedure and Password Protection is desired. Entering the Password The Password contains 4 digits, when the projector asks to enter your password: 1.
Page 28
When reentering the adjustment mode, it will be necessary to enter your password again when selecting a password protected item. When the password is wrong, the error message “Wrong Password !!!” will be displayed. R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
Some items in the Random access mode are password protected (when the password function is enabled). Enter your password to continue. All other password protected items are now also available if you stay in the adjustment mode. R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
Vertical Centerline Side Precorrection Left Fine Side Correction Top / Bottom Horizontal Centerline Horizontal Top Horizontal Bottom Size Fine Horizontal Adjustment Linearity Coarse Linearity Fine Vertical Linearity Fine Horizontal Linearity Blanking R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
When using the Internal # Pattern? The Internal # Pattern menu will be displayed if the Internal Cross Hatch Pattern has been selected or if no source is connected to the projector. R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
Page 32
3. Press ENTER if the desired block is selected. The menus in this manual are created for an external source, connected to one of the inputs, and the ’Gen- locked Pattern’ is selected. R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
By means of a fixed color balance. You have the choice between 3200 K (reddish), 4900 K, 6500 K (white) or 9300 K (bluish). • By means of a custom white and black balance. R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
’corner fall off’. Secondly, due to the normal off-axis projection of the red and blue images, CRT projection displays a phenomenon referred to as ’color shift’, whereby one side of the screen is "redish" an the other "blueish”. R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
Page 35
CONTRAST EQUALISATION RED GREEN BLUE CONTRAST EDGE CORRECTION RED GREEN BLUE COLOR SELECT RED GREEN BLUE RG RB BG WHITE Select with ↑ or ↓ then <ENTER> <EXIT> to return Menu 6-9 R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
Page 36
2. Adjust with the cursor keys for the same light output in the corners as in the center of the image. Push the ↑ or ↓ keys for top-bottom adjustments and push the ← or → keys for left-right adjustments. Note: Left-right adjustment must be done in combination with the top-bottom adjustment as both adjustments influence each other R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
2. Press ENTER to toggle between Fast or Slow. Note: Sync is normally set to Slow. The Fast position is used to compensate for unsteady sync pulses from older video playback equipment. R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
6.4.6 Clamp mode: Normal/Restoration What can be done? The clamp mode can be switch between Normal and Restoration. The clamp mode function is only available for RGBS, RGsB and component sources. R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
ADVANCED SETTINGS Select with ↑ or ↓ then <ENTER> <EXIT> to return Menu 6-19 2. Press ENTER to toggle Motion Processing On/Off. 3. Press EXIT to return to the Picture Tuning menu. R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
50Hz 625 Lines NI 50Hz 935 Lines NI 100Hz 625 Lines NI 50Hz 1250 Lines NI 100Hz 1250 Lines I Select with ↑ or ↓ then <ENTER> <EXIT> to return Menu 6-21 R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
The Video Equalizing menu will be displayed. FACTORY PRESET : x Select with ç or è Adjust or scroll presets with é or ê <EXIT> to return. Image 6-4 Video Equalizing menu R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
1. Push the ↑ or ↓ keys to highlight Contrast Enhancement and press ENTER to select. IMAGE PROCESSING MOTION PROCESSING: ON OUTPUT MODE VIDEO EQUALIZING NOISE REDUCTION CONTRAST ENHANCEMENT SPLIT SCREEN: OFF ADVANCED SETTINGS Select with ↑ or ↓ then <ENTER> <EXIT> to return Menu 6-26 R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
1. Push the ↑ or ↓ keys to highlight Advanced Settings and press ENTER to select. IMAGE PROCESSING MOTION PROCESSING: ON OUTPUT MODE VIDEO EQUALIZING NOISE REDUCTION CONTRAST ENHANCEMENT SPLIT SCREEN: OFF ADVANCED SETTINGS Select with ↑ or ↓ then <ENTER> <EXIT> to return Menu 6-28 R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
2. Push the ↑ or ↓ keys to adjust the Luminance Delay until the color shift is eliminated. 3. Press EXIT to return to the Line Multiplier menu. 6.4.8.8.4 Vertical Sync Reference What can be done? The Vertical Sync Reference can be set in 2 modes: R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
3. Press EXIT to return to the Limo Pro Options menu. 6.4.8.9.8 LTI What can be done? LTI = Luminance transient improvement. This function makes the luminance transients sharper (from dark areas to highlight areas) without overshoot, undershoot or ringing. R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
3. Press EXIT to return to the Limo Pro Options menu. 6.4.8.9.9 CTI What can be done? CTI = Chrominance (color) transient improvement. This function makes the chrominance transients (from one color to another) sharper without overshoot, undershoot or ringing. R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
What can be done? All settings for the Line Multiplier can be set to the Factory Presets. These Factory Presets settings are: Time Base Correction Luminance Delay Vertical Sync Reference Indirect Clamp Gating R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
• Horizontal Amplitude. • Vertical Amplitude. • Vertical Linearity . • Horizontal Phase. The convergence corrections are disabled during geometry corrections. The blanking corrections are only enabled during the blanking adjustments. R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
1. Push the ↑ or ↓ keys to highlight Horizontal Phase and press ENTER to select. GEOMETRY GREEN CONVERGENCE: ON H PHASE RASTER SHIFT LEFT-RIGHT (E-W) TOP-BOTTOM (N-S) SIZE FINE H SIZE LINEARITY BLANKING Select with ↑ or ↓ then <ENTER> <EXIT> to return Menu 6-40 R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
RASTER POSITION WRONG RASTER POSITIONS CRT phosphor width for the green color 11,5 cm (4.5 inch) CRT Faceplate holder Forbidden area Phosphor area Projected raster Image 6-14 R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
Note: Horizontal and Vertical shifts for Red and Blue should end up with a setting close to 50%. If these settings are significantly greater or lesser than 50%, contact a BARCO authorized service technician. 8. Press EXIT to return to the Geometry menu.
3. Use the ← or → keys to adjust the tilting of the vertical lines in the middle of the image. Image 6-16 Vertical Centerline: Skew Adjustment 4. Press EXIT to return to the Left-Right (E-W) menu. R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
VERTICAL CENTERLINE SIDE PRECORRECTION LEFT FINE SIDE CORRECTION WARNING: USE SIDE PRECORRECTION TO ADJUST THE RIGHT SIDE OF THE IMAGE Select with ↑ or ↓ then <ENTER> <EXIT> to return Menu 6-46 R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
3. Use the cursor keys to correct the sides of the image in this specific area. 4. Press ENTER to save the correction and to return to the selection screen. 5. Press EXIT to return to the Left-Right (E-W) menu. R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
HORIZONTAL CENTERLINE HORIZONTAL TOP HORIZONTAL BOTTOM Select with ↑ or ↓ then <ENTER> You can adjust BOW with ↑ or ↓ and KEYSTONE with ← or → <EXIT> to return Menu 6-49 R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
3. Use the ← or → keys to adjust the tilting of the horizontal lines on the top of the image. Image 6-25 Horizontal Top: Skew Adjustment 4. Press EXIT to return to the Top-Bottom (N-S) menu. R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
In order to avoid loss of resolution in the projected image and to ensure maximum CRT longevity, do not use an excessively small size setting. If the internal # pattern was selected, this pattern remains on the screen, if the genlocked pattern was selected, the external source will be displayed. R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
Page 60
3. Push the ↑ or ↓ keys to adjust the vertical size until the exact image height is obtained. Ideal Image Image image height short tall Image 6-30 Vertical Size Adjustment R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
1. Push the ↑ or ↓ keys to highlight Linearity and press ENTER to select. GEOMETRY GREEN CONVERGENCE: ON H PHASE RASTER SHIFT LEFT-RIGHT (E-W) TOP-BOTTOM (N-S) SIZE FINE H SIZE LINEARITY BLANKING Select with ↑ or ↓ then <ENTER> <EXIT> to return Menu 6-54 R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
2. Push the ← or → keys to adjust the horizontal linearity until the distances between the vertical lines of the set up pattern are equal from left to right. 5. Only to be done when the projector is equipped with the optional linearity option. R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
Select with ↑ or ↓ then <ENTER> <EXIT> to return Menu 6-58 2. Push the ↑ or ↓ keys to select one of the 9 possible areas and press ENTER to confirm. R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
Select with ↑ or ↓ then <ENTER> <EXIT> to return Menu 6-59 The Blanking menu will be displayed. BLANKING BOTTOM LEFT RIGHT Select with ↑ or ↓ then <ENTER> <EXIT> to return Menu 6-60 R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
Adjust the red and blue until they exactly match with the green lines. green image red image Convergence Adjustment Image 6-35 Convergence Adjustment Adjustment order Adjust first the coarse adjustment and continue with the fine adjustment. R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
4. Press ENTER to finish convergence adjustment and to toggle the cursor keys to the selection mode. 5. Repeat step 2 till 4 for each area that needs an adjustment. 6. Press EXIT to return to the Convergence. R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
6. Press EXIT to return to the Convergence menu when the convergence for that item is finished. 7. Repeat the same procedure for Red on Green and Blue on Green. 8. Press EXIT to return to the Random Access Adjustment Mode menu. R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
Red and Blue, push the ↑ or ↓ keys to highlight Green and press ENTER to select. FOCUSING GREEN BLUE BLUE ON SOURCE Select with ↑ or ↓ then <ENTER> <EXIT> to return Menu 6-65 The Green Focusing menu will be displayed. R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
Select with ↑ or ↓ then <ENTER> <EXIT> to return Menu 6-68 2. Push the cursor keys until the lower part of the image is sharp. 3. Press ENTER to return to the Focusing menu. R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
Menu 6-70 2. Repeat the procedures mentioned above (Midpoint, Top, Bottom and Digital Adjustment Focusing) to improve white uniformity. 3. Keep pressing EXIT until the Random Access Adjustment Mode menu is displayed. R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
1. Push the ↑ or ↓ keys to highlight Driver Voltage and press ENTER to select. RANDOM ACCESS ADJUSTMENT MODE PICTURE TUNING GEOMETRY CONVERGENCE FOCUSING COLOR SELECT SOFT EDGE DRIVER VOLTAGE Select with ↑ or ↓ then <ENTER> <EXIT> to return Menu 6-72 R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
Page 72
If no, Use the cursor keys to drive up the Driver Voltage a little and try again to converge the image, repeat this step if necessary. Tip: Do not exaggerate as the dissipation inside the projector will increase too. 3. Press EXIT to return to the Random Access Adjustment Mode menu. R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
Some items in the Service mode are password protected (when the password function is active). Enter your password to continue. All other password protected items are now also available if you stay in the adjustment mode. R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
CHANGE PASSWORD CHANGE PROJECTOR ADDRESS CHANGE BAUDRATE PROJECTOR WARM UP POWER UP MODE: operating COMMON ADDRESS: 0 ABL CONTROLLER Select with ↑ or ↓ then <ENTER> <EXIT> to return Menu 7-4 R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
1. Push the ↑ or ↓ keys to highlight the desired CRT e.g. Red, for which the Run Time has to be reseted. RUN TIME SYSTEM RUNTIME: 120 h CRT RUNTIME RED: 20 h GREEN: 20 h BLUE: 50 h Select with ↑ or ↓ then <ENTER> <EXIT> to return Menu 7-8 R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
6. Press ENTER to confirm, press EXIT to cancel the saving. 7.3.5 Change Projector Address What can be done? Every projector requires an individual address between O and 255. This address can be set by the software. R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
CHANGE PASSWORD CHANGE PROJECTOR ADDRESS CHANGE BAUDRATE PROJECTOR WARM UP POWER UP MODE: operating COMMON ADDRESS: 0 ABL CONTROLLER Select with ↑ or ↓ then <ENTER> <EXIT> to return Menu 7-13 R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
PROJECTOR WARM UP POWER UP MODE: operating COMMON ADDRESS: 0 ABL CONTROLLER Select with ↑ or ↓ then <ENTER> <EXIT> to return Menu 7-15 The Projector Warm Up menu will be displayed. R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
2. Push the ↑ or ↓ keys to highlight a Warm Up Block. 3. Press ENTER to copy the settings of the selected block to the warm up block. 4. Press EXIT to return to the Projector Warp Up menu. R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
CHANGE PASSWORD CHANGE PROJECTOR ADDRESS CHANGE BAUDRATE PROJECTOR WARM UP POWER UP MODE: operating COMMON ADDRESS: 0 ABL CONTROLLER Select with ↑ or ↓ then <ENTER> <EXIT> to return Menu 7-21 R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
POWER UP MODE: operating COMMON ADDRESS: 0 ABL CONTROLLER Select with ↑ or ↓ then <ENTER> <EXIT> to return Menu 7-23 2. Press ENTER to select. The ABL Controller menu will be displayed. R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
Page 83
Note: ABL can also be controlled by a PC through RS232, in this case the ABL Timer is disabled by setting the ABL timer to zero. 4. Press ENTER to confirm. 5. Press EXIT to return to the ABL Controller menu. 6. Press EXIT to return to the Service Mode menu. R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
3. Press ENTER to copy the settings of the selected block to the active block you are working on. Note: All current settings will be overwritten with the settings of the block which is copied. A confirmation screen will be displayed. R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
2. Push the ↑ or ↓ keys to select a block. 3. Press ENTER to delete the selected block. A confirmation screen will be displayed. 4. Press ENTER to confirm, press EXIT to cancel the deletion. R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
COPY SOFT EDGE BLOCK DELETE A BLOCK DELETE ALL BLOCKS SET TO MIDPOSITION Select with ↑ or ↓ then <ENTER> <EXIT> to return Menu 7-32 The Set to Midposition menu will be displayed. R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
2. Press ENTER to reset the Red and Blue Convergence settings to the previous settings. 7.4.6.3 Green Convergence Midposition Only available when the projector is equipped with the green convergence adjustments. What can be done? All Green convergence settings can be set to midposition. R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
<EXIT> to return Menu 7-37 2. Press ENTER to set the Focus settings to midposition. A confirmation screen will be displayed. 3. Press ENTER to confirm, press EXIT to cancel the reset. R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
UNDO ASTIGMATISM MIDPOSITION UNDO ALL SETTINGS TO MIDPOS Select with ↑ or ↓ then <ENTER> <EXIT> to return Menu 7-40 2. Press ENTER to reset the East–West settings to the previous settings. R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
Menu 7-43 2. Press ENTER to set the Digital Vertical Linearity settings to midposition. A confirmation screen will be displayed. 3. Press ENTER to confirm, press EXIT to cancel the reset. R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
UNDO ALL SETTINGS TO MIDPOS Select with ↑ or ↓ then <ENTER> <EXIT> to return Menu 7-46 2. Press ENTER to reset the Digital Horizontal Linearity settings to the previous settings. R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
Menu 7-49 2. Press ENTER to set all Set to Midposition menu settings to midposition. A confirmation screen will be displayed. 3. Press ENTER to confirm, press EXIT to cancel the reset. R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
PROJECTOR SET-UP MEMORY MANAGEMENT COMMON SETTINGS I2C DIAGNOSTICS VOLTAGE DIAGNOSTICS PROJECTOR DIAGNOSTICS Select with ↑ or ↓ then <ENTER> <EXIT> to return Menu 7-51 The Common Settings menu will be displayed. R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
Menu 7-52 The Dynamic Astigmatism menu will be displayed. 2. Push the ↑ or ↓ keys to highlight Dynamic Astigmatism and press ENTER to select. The Dynamic Astigmatism menu will be displayed. R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
Page 95
Push the ← or → keys for the axial astigmatism adjustment. 4. Press EXIT to return to the area selection mode. 5. Repeat step 2 till 6 for each area that needs an adjustment. R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
If yes, Press ENTER to continue (Further description of the Gamma Corrections are given in the installation manual). If no, Press EXIT to return to the Common Settings menu. 7.5.4 CRT Run In Cycle When necessary? Only necessary when a new picture tube is installed. R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
Higher drive current to the CRT’s, the lifetime of the CRT’s will shorten but the light output will be higher. This setting will be saved in the EEPROM. When restarting the projector, it will start up in boost mode. R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
Off, only the first memory bank will be used to display the source. How to create a New Memory Bank? 1. Select the desired source using the RCU e.g. source 1 (Video 64 kHz, 60 Hz). R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
3. Press ENTER to activate the Flyback Turnover Point Frequency. 7.5.8 Menu Position What can be done? The bar scale menu, warning and message boxes can be displayed in the right lower corner or in the middle of the screen. R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
FLYBACK TURNOVER POINT MENU POSITION: STANDARD OPTION 1: REAL TIME CLOCK Select with ↑ or ↓ then <ENTER> <EXIT> to return Menu 7-67 The Real Time Clock menu will be displayed. R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
2. Push the ↑ or ↓ keys to scroll through the failure list. 3. Press EXIT to return to the Service Mode menu. When no errors are detected a “No errors on IC2–bus detected” will be displayed. R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
1. Push the ↑ or ↓ keys to highlight Projector Diagnostics and press ENTER to select. SERVICE MODE PROJECTOR SET-UP MEMORY MANAGEMENT COMMON SETTINGS I2C DIAGNOSTICS VOLTAGE DIAGNOSTICS PROJECTOR DIAGNOSTICS Select with ↑ or ↓ then <ENTER> <EXIT> to return Menu 7-73 R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
Page 103
+209 Volt HTHD: +124.5 Volt -conv: -32.4 Volt +conv: +33.1 Volt foc_lo: +28.8 Volt foc_hi: +41.3 Volt <EXIT> to return. Menu 7-75 4. Press EXIT to return to the Projector Diagnostics menu. R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
WARNING: permanent BOOST mode in The CRT drive mode is switched to permanent boost. use !!! WARNING: Option not installed ! Option not installed. e.g. Video selected but no decoder installed. R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
Input not valid FAILURE PC communication error Error in the communication between the projector and the PC. FAN FAILED Projector will switch off Projector switched off due to a fan fail. R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
42–43 CRT Drive Mode Start up CRT Run In Cycle Line Multiplier (Optional) 35–36 settings 35–36 Start up Linearity 57–59 Adjustment Start up Diagnostics 97–98 Coarse Fine Projector Horizontal Voltage Vertical R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
Page 108
Tri Level Sync (Optional) Power Up Operating/Stand By Projector 17–20, 70–71, 73, 75 Time Base Correction Address 19, 73 Top-Bottom Change Adjustments Controlling Start up Controlling Total Run Time Set-Up 70–71 Start up R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...
Page 109
Index Frequency On/Off Vertical Centerline Time Vertical Sync Reference Warm up period Video Equalizing Interrupt Warnings Warm Up 76–77 R5976633 BARCO GRAPHICS 908 / BARCO REALITY 908 05/06/2003...