Related Manuals for Barco Data 1209s
Summary of Contents for Barco Data 1209s
- Page 1 All manuals and user guides at all-guides.com DATA 1209s R9002250 R9002259 INSTALLATION MANUAL...
- Page 2 All manuals and user guides at all-guides.com BARCO PROJECTION SYSTEMS DATA 1209s R9002250 R9002259 INSTALLATION MANUAL Date : Rev. : Art. No. : 040698 R5975718...
- Page 3 All manuals and user guides at all-guides.com BARCO nv/Projection Systems Noordlaan 5 B-8520 Kuurne Belgium Tel : +32/56/368211 Fax : +32/56/351651 E-mail : sales.bps@barco.com Visite Barco at the web : http://www.barco.com Printed in Belgium...
-
Page 4: Table Of Contents
All manuals and user guides at all-guides.com Table of contents TABLE OF CONTENTS ..........................I-1 SAFETY INSTRUCTIONS On safety ............................. 1-1 On installation ............................1-2 On servicing ............................1-2 On cleaning............................1-2 On repacking ............................1-2 On illumination ............................. 1-2 UNPACKING AND PROJECTOR DIMENSIONS Unpacking ............................ -
Page 5: Table Of Contents
Projector Distance ..........................8-2 Optical Lens Focusing ......................... 8-2 Raster Centering ..........................8-3 CRT Projection Angle Adjustment ....................... 8-4 Scheimpfug Adjustment ........................8-6 Appendix A : Barco ceiling mount support Appendix B : G2 adjustment Appendix C : Gamma corrections... -
Page 6: Safety Instructions
Before operating this equipment please read this manual thoroughly, and retain it for future reference. Installation and preliminary adjustments should be performed by qualified BARCO personnel or by author- ized BARCO service dealers. Note : The use of shielded cables is required to comply within the limits of Part 15 of FCC rules and EN55022. -
Page 7: On Installation
All manuals and user guides at all-guides.com Safety Instructions On cleaning On installation On repacking On illumination On servicing... -
Page 8: Unpacking And Projector Dimensions
All manuals and user guides at all-guides.com Unpacking and dimensions UNPACKING AND PROJECTOR DIMENSIONS Unpacking Contents of the shipping carton : • • • • • •... -
Page 9: Projector Dimensions
All manuals and user guides at all-guides.com Unpacking and dimensions Projector dimensions (in mm) -
Page 10: Installation Guidelines
All manuals and user guides at all-guides.com Installation guidelines INSTALLATION GUIDELINES Installation guidelines Careful consideration of things such as image size, ambient light level, projector placement and type of screen to use are critical to optimize the use of the projection system. Environment What about ambient light ? Which screen type? -
Page 11: Where To Install The Projector
All manuals and user guides at all-guides.com Installation guidelines Where to install the projector ? prvyvt ƒ…‚wrp‡‚… †p…rr A…‚‡Ã‰vr †p…rrÃvq‡u U‚ƒÃ‰vr Abbreviations used in the calculations and the drawings : Used phosphor width on the CRT faceplate (e.g. green CRT) 11.5 cm green phospho Mounting Configuration... -
Page 12: Installation Set-Up
All manuals and user guides at all-guides.com Installation set-up INSTALLATION SET-UP WARNING : Risk of electric shock ! Installation only by BARCO authorized service personel ! Access to Controls Opening the top cover Lock screws WARNING : Removing the top cover... -
Page 13: Scan Adaptation
All manuals and user guides at all-guides.com Installation set-up Scan Adaptation WARNING ! TURN OFF PROJECTOR AND UNPLUG THE POWER CORD BEFORE CHANGING THE SCAN DIRECTION. Gaining access to the scan switches ⊇ ⊄ ⊂ Í ∈... - Page 14 All manuals and user guides at all-guides.com Installation set-up − C‚…v“‚‡hyà Wr…‡vphyà qrsyrp‡v‚Æv‡pur† qrsyrp‡v‚Æv‡pu − Q…‚wrp‡‚…Ãp‚svtˆ…h‡v‚†ÃTv‡puÆr‡‡vt† )URQWFHLOLQJ 5HDUFHLOLQJ SUHVVHG SUHVVHG SUHVVHG SUHVVHG 5HDUWDEOH A…‚‡‡hiyr SUHVVHG SUHVVHG SUHVVHG SUHVVHG Attention : This procedure can only be done after power (mains) connection. So, first continue with the projector set-up and the connections and then return to this procedure.
- Page 15 All manuals and user guides at all-guides.com Installation set-up 'IDENTIFICATION' SERVICE MODE IDENTIFICATION COPY A BLOCK DELETE A BLOCK DELETE ALL BLOCKS CHANGE PASSWORD CHANGE LANGUAGE RUN TIME DYNAMIC ASTIGMATISM MORE... Select with then <ENTER> <EXIT> to return 'IDENTIFICATION SCREEN' 'Config' Proj.
-
Page 16: Projector Set-Up
All manuals and user guides at all-guides.com Projector set-up PROJECTOR SET-UP SET-UP − − − − PASSWORD MODE POWER UP MODE PASSWORD REQUIRED OPERATING MODE WHEN FOR ADJUSTMENT POWER IS SWITCHED ON PLAYING StdBY BAUD RATE TABLE TO COMPUTER PROJECTOR ADDRESS StdBY (sum) CODE... -
Page 17: Setting The Projector Address
All manuals and user guides at all-guides.com Projector set-up Setting the projector address ρ ρ Addressable with RCU Addressable with PC, MAC or workstation 202 : PROJECTOR ADDRESS... -
Page 18: Power-Up Mode
All manuals and user guides at all-guides.com Projector set-up Power-up mode Operational mode Source 2 Fh= 15.6 kHz Fv= 50 Hz Stand-By mode Baud Rate for communication with a computer OFF ON... -
Page 19: Password Mode
All manuals and user guides at all-guides.com Projector set-up Password mode <ADJUST> OFF ON... -
Page 20: Ac Power Connection
All manuals and user guides at all-guides.com AC power connection AC POWER CONNECTION AC Power (mains) cord connection V NOM 120/230 Volt I MAX 7/5Amp FREQ 50/60Hz à D " à P " ST!"!ÃDI ST!"!ÃPV U S@H P U@ Preparing your power cord Mains lead (power cord) with CEE7 plug −... -
Page 21: Ac Power Check
All manuals and user guides at all-guides.com AC power connection AC Power check When the power voltage is different from that of the wall outlet, proceed to AC Input power voltage adaptation of the projector. AC Input power (mains) voltage adaptation BARCODATA 1209s - R9002250 230 Vac BARCODATA 1209s - R9002259... -
Page 22: Switching On The Projector
All manuals and user guides at all-guides.com AC power connection Fuses − − Switching on the projector − − − − Starting up with a full white image PROJECTOR WARM UP A FULL WHITH PATTERN WILL BE GENERATED FOR 20 MINUTES Start up with "Warm up period"... - Page 23 All manuals and user guides at all-guides.com AC power connection Start up without "Warm up period" Warning : Skipping this warm up procedure can reduce the initial picture quality of the projected image.
-
Page 24: Source Connections
All manuals and user guides at all-guides.com Source connections SOURCE CONNECTIONS Signal input connection The following signals can be connected to the projector through the inputs on the back panel of the projector : QPSUÃ#$ QPX @S H6 DI T QPSUÃ... -
Page 25: Connecting A S-Video (Or Composite Video) Source To Port 2
All manuals and user guides at all-guides.com Source connections Connecting a S-Video (or Composite Video) 4 pin connector configurations: source to Port 2 For S-video: For video: Pin 1: earth(ground) luminance Pin 1: earth(ground) video Pin 2: earth(ground) chrominance Pin 2: not connected Pin 3: video signal Pin 3: luminance signal(Y) Separate Y-luma/C-chroma signals for higher quality playback of... -
Page 26: Connecting A Rgb Analog Source To Port 3
An interface is recommended when connecting a computer and local monitor to the projector. BARCO provides the following interfaces: Universal Analog Interface - Order no. : R9826100. RGB 120 MHz Analog Interface - Order no. : R9826570. -
Page 27: Connecting A Rgb Analog Source With Tri-Level Sync To Port 4/5 (Option)
All manuals and user guides at all-guides.com Source connections Connecting a RGB Analog source with Tri- QPSUÃ#$ QPX@SH6DIT QPSUà QSPE@8UPSÃHP9@ SB7ÃÃCW WD9@P BS@@IÃ)ƒr…h‡v‚hy level sync to Port 4/5 (option) 8‚€ƒCÆ’p WÆ’p S@9Ã)Ƈhqi’ QPSUÃ%à S@HPU@ QPSUÃ" 8PHHVID86UDPI QPSUÃ! TWD9@P RGB analog input terminals with Tri-level sync input or with Tri-level &$Âu€... -
Page 28: Installation Adjustment Mode
ARE RESERVED TO, AND TO BE PERFORMED ONLY switch to the internal pattern on 15 kHz/50 Hz. BY BARCO PERSONNEL, OR BARCO AUTHORIZED DEALERS 4 When the password mode is active, you will be requested to enter IF QUALIFIED, PRESS <ENTER>... -
Page 29: Projector Distance
All manuals and user guides at all-guides.com Installation adjustment mode Important : Access to adjustments The top cover of the projector should be removed in order to gain access to the adjustments. Projector Distance On the screen, a drawing will be displayed together with parameters FHLOLQJ indicating a correct installation position. -
Page 30: Raster Centering
All manuals and user guides at all-guides.com Installation adjustment mode Raster Centering The raster must be centered on the CRT faceplate of each tube, therefore, it is necessary to look into the lenses. RASTER CENTERING Caution : To avoid eye discomfort while performing these adjust- CONTRAST LEVEL IS REDUCED ments, reduce the contrast and gradually increase the brightness AND BRIGHTNESS INCREASED... -
Page 31: Crt Projection Angle Adjustment
All manuals and user guides at all-guides.com Installation adjustment mode CRT Projection Angle Adjustment The projection angle of the red and blue CRT's is dependent on the desired size of the projected image. If the centers of green, blue and red do not coincide, the CRT projection angle must be adjusted. - Page 32 All manuals and user guides at all-guides.com Installation adjustment mode Loosen bolts D, E and F to pivot the blue CRT until the center of the Blue image and the center of the Green image coincide. When the angle of the blue CRT is corrected, tighten the four bolts. Press ENTER to continue with the diagonal focusing menu.
-
Page 33: Scheimpfug Adjustment
All manuals and user guides at all-guides.com Installation adjustment mode Scheimpflug Adjustment (Diagonal image focusing) With the diagonal image focusing corrections, it is possible to obtain uniform focus for the total projected image. DIAGONAL IMAGE FOCUSING These corrections must be repeated for each colour. The Diagonal 1. - Page 34 All manuals and user guides at all-guides.com Installation adjustment mode Repeat the same procedure for the red and blue image using the corresponding screws. To optimize the image focusing, repeat the optical lens focusing. When the scheimpflug corrections are correctly adjusted, secure this position by fastening the security screws on both sides of each LENS lens.
-
Page 35: Appendix A : Barco Ceiling Mount Support
All manuals and user guides at all-guides.com Appendix A: BARCO ceiling mount support BARCO CEILING MOUNT SUPPORT The order number: R5975693 Contents of the installation guidelines Overview drawing of the total system 8 @I U@S ȃƒr…ƈ ƒƒ‚…‡ H 6YÃG@ IB CUà Ã8 H 9DTU6I8@ÃT8S@@IÃASPIU... - Page 36 All manuals and user guides at all-guides.com Appendix A: BARCO ceiling mount support Projector-position corrections * Water-level adjustment * Projector axis adjustment...
-
Page 37: Appendix B : G2 Adjustment
All manuals and user guides at all-guides.com Appendix B: G2 adjustment G2 ADJUSTMENT B !Ã69EVTUH @I U Use the potentiometers on the G2-ADJ. module to set the screen grid voltage for Red, Green and Blue. Adjust until the LED on the corresponding output amplifier is turned off. -
Page 38: Appendix C : Gamma Corrections
All manuals and user guides at all-guides.com Gamma corrections GAMMA CORRECTIONS WARNING RISK OF INCORRECT ADJUSTMENT OF THE "RISK OF INCORRECT ADJUSTMENT OF THE PROJECTOR. PROJECTOR. THE GAMMA CORRECTIONS ARE FACTORY ADJUSTED USING AN ACTAS COLOR ANALYSER ! THEREFORE, ONLY QUALIFIED THE GAMMA CORRECTIONS ARE INSTALLATION OR SERVICE PERSONNEL SHOULD PERFORM FACTORY ADJUSTED USING AN... - Page 39 All manuals and user guides at all-guides.com Gamma Corrections R & B MIDLIGHTS GAMMA CORRECTIONS Service BLUE GAMMA CORRECTION Adjust slope with é or ê Breakpoint with ç or è R & B MIDLIGHTS Adjust red with é or ê blue with ç...
- Page 40 All manuals and user guides at all-guides.com MATERIAL SAFETY DATA SHEET (Federal Supply Code for Manufacturer's) BARCO N.V. 32-56-368211 (Number, Street, City, State, and ZIP Code) Noordlaan 5 B-8520 KUURNE Ethylenglycol & Glycerol Cooling liquid 512334 Polyalcohols (FSN) (LBS) (Units)
- Page 41 All manuals and user guides at all-guides.com 100ppm (Materials to avoid) Rinse with water (Specific type) (General) Harmful if swallowed Keep out of the reach of children To avoid from oxidants THE INFORMATION CONTAINED HEREIN IS BASED ON DATA CONSIDERED ACCURATE. HOW- EVER, NO WARRANTY IS EXPRESSED OR IMPLIED REGARDING THE ACCURACY OF THESE DATA OR THE RESULTS TO BE OBTAINED FROM THE USE THEREOF.