JSI Flux Installation Instructions Manual
Adjustable u-unit assembly
Hide thumbs
Also See for Flux:
- Installation instructions (3 pages) ,
- Installation instructions (2 pages) ,
- Installation instructions (2 pages)
Advertisement
Quick Links
Flux
Recommended Tools
Screw Gun
Tape Measure
Level
Hex Wrench
Hardware Used
#8 x 1
1
" Flat Head Wood Screws
/
4
#8 x 1
1
" Flat Head Wood Screws
/
2
Package Contents
Lateral File
Credenza
Notice To Installers: Failure to comply with installation instructions will compromise the safety, durability and performance of this product, which may risk injury to the user of this
product and/or diminish the product life cycle. Jasper Group assumes no liability in these instances.
#2 Phillips Head Bit
#2 Phillips Screw Driver
Bridge Top
Assembly
End Panel
End Panel
jsifurniture.com
812.482.3204
800.457.4511
812.482.1548
Adjustable U-Unit Assembly
#8 x
3
225 Clay Street / PO Box 231
O
Jasper, Indiana 47546
F
Installation Instructions
" Flat Head Wood Screws
/
4
Fixed Modesty
Panel
Page 1 of 10
Desk Top
Assembly
Optional Modesty
Panel
Form No. INST-FL001
5/7/18
Advertisement
Related Manuals for JSI Flux
Summary of Contents for JSI Flux
- Page 1 Installation Instructions Flux Page 1 of 10 Adjustable U-Unit Assembly Recommended Tools Screw Gun Tape Measure #2 Phillips Head Bit Level #2 Phillips Screw Driver Hex Wrench Hardware Used #8 x 1 ” Flat Head Wood Screws #8 x ” Flat Head Wood Screws #8 x 1 ”...
- Page 2 Installation Instructions Flux Page 2 of 10 Step 1 Adjustable U-Unit Assembly Position and Level all Units (continued) • Position adjustable desk panel base and adjustable return panel base in desired location. The length of desk will determine the spacing of the two bases.
- Page 3 Installation Instructions Flux Page 3 of 10 Step 2 Adjustable U-Unit Assembly Attach Fixed Modesty Panel (continued) Position and Level all Units • Position adjustable desk panel base and adjustable return panel base in desired location. The length of desk will determine the spacing of the two bases.
- Page 4 Installation Instructions Flux Page 4 of 10 Step 3 Adjustable U-Unit Assembly Attach Worksurfaces (continued) • Carefully lower Desk Top Assembly into place Fasten understucture to adjustment columns using eight (8) #6 X 12mm socket head bolts, four (4) per side.
-
Page 5: Step 4 Connect Electrical Wiring
Installation Instructions Flux Page 5 of 10 Step 4 Adjustable U-Unit Assembly Connect Electrical Wiring (continued) • Carefully lower Desk Top Assembly into place To height control switch Dongle To any of the adjustable columns To any of the adjustable columns... - Page 6 Installation Instructions Flux Page 6 of 10 Step 5 Adjustable U-Unit Assembly Secure Worksurfaces To (continued) Adjustable Height Columns Raise worksurface for easier access to understructure Using hex wrench, tighten all machine bolts firmly to the three columns Notice To Installers: Failure to comply with installation instructions will compromise the safety, durability and performance of this product, which may risk injury to the user of this Notice To Installers: Failure to comply with installation instructions will compromise the safety, durability and performance of this product, which may risk injury to the user of this product and/or diminish the product life cycle.
- Page 7 Installation Instructions Flux Page 7 of 10 Step 6 Adjustable U-Unit Assembly Fasten Bridge To • Push worksurfaces together so (continued) Main Worksurface all surfaces and edges are tight and flush to one another • While worksurfaces are being held...
- Page 8 Installation Instructions Flux Page 8 of 10 Step 8 Adjustable U-Unit Assembly Attach Wire Manager (continued) (Optional) Attach wire manager Attach wire manager to underside of surface to underside of surface and route wire accordingly and route wire accordingly 4 ”...
- Page 9 Installation Instructions Flux Page 9 of 10 Step 9 Adjustable U-Unit Assembly Route Power Cord (continued) Through Wire Manager Route power cord through wire manager Replace door and lower worksurface to desired height. Attach magnet on wire manager to the flat bracket...
- Page 10 Installation Instructions Flux Page 10 of 10 Step 10 Adjustable U-Unit Assembly Attach Credenza (continued) Adjust height of unit to be flushLevel unit front-to-back and side-to-side by rota ting adjustable glides. Fasten credenza to unit using L-brackets and #8 x ”...