Galaxy Control Systems 635 Series Installation/Configuration Manual page 33

Table 6: BOARD COMPATIBILITY CHART for SG 10/11
WHEN IS UPGRADING SG SOFTWARE REQUIRED ?...
if an SG version is noted, then that is the minimum version of SG required to support that board/feature

if the no version is listed, then any version of SG 10 supports the feature.

WHEN IS UPGRADING HARDWARE REQUIRED ?...
Installing Wireless Readers, IP Readers – you must upgrade to 635 CPU and 635-DSI

Installing 635-Input Module – you must upgrade to 635 CPU and 635-DSI

Installing a Galaxy 485 Remote Door Module – You must upgrade to 635-CPU, 635-DRM, and 635-DSI.

Installing newer destination-driven elevator systems, then you must install all 635-model hardware.

• 600-model boards can interoperate with 635-model boards in the same system and within the same control panel.
You can replace older 600-model boards with new 635-model boards as needed.
•
The older 600-model boards do not support the newer hardware interfaces and features supported by the 635.
•
635-SERIES CONTROLLER
635 CPU Board -
Processor
• Operates in same loop /system with 600 CPUs
• Supports all 635 & 600 daughter boards
• Supports all 635-series RS485 Modules
• Supports all 600-series RS485 Modules – restrictions apply
• Supports Destination-driven elevator systems
• Supports Card Tour Board
635 DAUGHTER BOARDS

635 DRM Reader Board
635 DSI Serial Board
• 600 Output Module (general
output or elevator control)
• LCD Clock unit
• Schlage PIM 485 ODT (legacy)
• Assa Abloy Aperio (SG 10.1)
• Salto Salis Wireless (SG 10.2)
• Schlage AD-300 (SG 10.2)
• Schlage AD-400 Wifi (10.2)
• or Mix AD-300/AD-400 (10.2)
• Assa IP Readers (SG 10.4)
• 635 Input Module (SG 10.4)
• 635 Remote Door DRM (10.4)
COMPATIBLE MODULES (RS-485 multi-drop)
600 Elevator/Output Module
635 Door Module (using 635 CPU & DSI, SG 10.3)
635 Input Module (using 635 CPU & DSI, SG 10.4)
635/600-SERIES H ARDW ARE I NSTALL GUIDE
*
600 DAUGHTER BOARDS
600 DIO Board
600 DPI Reader Board
600 DSI Serial Board
• 600 Output Module (general
output or elevator control)
• LCD Clock unit
• Schlage PIM 485 ODT (legacy)
• Assa Abloy Aperio (SG 10.1)
• Salto Salis Wireless (SG 10.2)
• Schlage AD-300 (SG 10.2)
• Schlage AD-400 Wifi (10.2)
• or Mixed AD-300/AD-400 (10.2)
• Assa IP Readers (SG 10.4)
<< Not supported on 600-DSI
<< Not supported on 600-DSI
( using DSI )
(
Tables 7 & 8 for SG-9 or lower
600-SERIES CONTROLLER
600 CPU Board – Processor
• Operates in same loop /system with 635 CPUs
• Compatible/Supports all 600 daughter boards
• Supports 635 DRM (Reader board)
• Supports 600 Output/Elevator Modules on 600 DSI
• Destination-driven elevator systems and Card Tour are not supported.
635 DAUGHTER BOARDS

635 DRM Reader Board
635 DSI Serial Board
• 600 Output Module (general
output or elevator control)
• LCD Clock unit
• Schlage PIM 485 ODT (legacy)
<< Not supported on 600-CPU
<< Not supported on 600-CPU
COMPATIBLE MODULES (RS-485 multi-drop)
600 Elevator/Output Module
<< 635 Door Module not supported on 600 CPU
<< 635 Input Module not supported on 600 CPU
Chapter-Page 1-20
)
600 DAUGHTER BOARDS
600 DIO Board
600 DPI Reader Board
600 DSI Serial Board
• 600 Output Module (general
output or elevator control)
• LCD Clock unit
• Schlage PIM 485 ODT (legacy)
<< Not supported on 600-CPU
<< Not supported on 600-CPU
( using DSI )