Warranty - Nordpeis Salzburg M Installation Manual

By top connection to steel chimney, we refer to the
respective manufacturer's installation instructions.
Requirements for Floor Plate by Combustible Floor
Follow the requirements for floor plate (stone, steel,
etc.) that apply in the country that the product is
installed in.
Glue
The outer elements should be glued with the acrylic
which is included. Make sure that all the surfaces that
are to be glued are free of dust. The surfaces can be
cleaned for better adhesion. Ensure that the surfaces
are dry before spreading on the acrylic. Once the
fireplace is assembled, fill the joints with acrylic and
even it out with a sponge or finger and some soapy
water, in order to have a clear indentation between the
elements (FIG Z).
Minor Dents
Transportation and handling can cause minor dents to
the product. This can be repaired with the powder glue
which is included. For a perfect result you can fill and
grind with a suitable filler on top of the powder glue.
Fill smaller cracks and uneven surfaces with a float or
a brush. If the dent is deep, it is recommended to fill in
several stages to avoid sinking. Even out with e.g. a
damp sponge or a float.
Painting
The surface of the chimney surround is developed to be
painted without priming work. Use latex or acrylic based
paint (emulsion paint), or cement-based textured paint.
In the unlikely case that there are some irregularities in
the surface, these can be filled with the acrylic which is
included, or a light and appropriate filling material. Any
surface that has been filled needs to be smoothened
with fine sand paper.
Polishing
If a more traditional and polished surface is wished for,
it is recommended to dampen the surround and then
cover it with tile adhesive (powder glue) and a fibreglass
mesh, prior to possibly adding mortar or mineral polish.
Tiles
This fireplace can also be partially or completely
covered with tiles / natural stone of your choice. As for
the section above on "Polishing", we recommend that
the chimney surround is dampened before it is covered
with tile adhesive (powder glue) and a fiberglass mesh.
This is to ensure good adhesion and prevent the
formation of cracks at the joints of the surround.
Please note that the adhesive and mortar must
set before burning in the fireplace. Follow the
instructions from the mortar/adhesive producers.
Regardless of surface treatment it is advantageous to
mask the entire doorframe to avoid having to clean it
later.
Please note that the air gap between the surround
and the door frame must not be filled with glue,
mortar or similar.
Thermotte®
The insulating plates in the burn chamber contribute to
a high combustion temperature, which leads to cleaner
combustion of the wood and a higher rate of efficiency.
Any fissures in the plates will not reduce their insulation
efficiency. If new plates are needed, contact your
dealer.
Please note: Wood logs that are too long can cause
additional strain and crack the plates, due to the tension
created between the side plates. Also note that the
Thermotte® plates may release coloured dust when
touched.
Cracks in the i PowerStone
Due to thermal effects there may be small cracks /
fissures in the PowerStone. This is natural and does not
affect the product's function or safety.

Warranty

Nordpeis Salzburg M benefits of a 5 years warranty.
The warranty requires the product to be installed in
accordance with applicable laws and regulations, as
well as the user manual. Notification of damage and
any consignment of parts for replacement must be done
immediately to the retailer where the stove was bought.
Any claim must be submitted with a dated purchase
invoice or a valid warranty card and serial number.
The warranty does not include consumables such
as: Thermotte®, smoke baffle, glass and gaskets.
Should any of the mentioned parts break, or need to
be changed due to wear and tear, new parts can be
ordered from your retailer. However, if a material or
production error can be documented on any of the
mentioned parts, the warranty is valid for 2 years after
the date of purchase.
The warranty does not include damages that are
caused by wrong installation or misuse of the stove,
e.g. incorrect draught regulation or use of incorrect
combustion material. The warranty does neither include
interference with operations outside the control of
Nordpeis, such as chimney draught etc. There is no
compensation for third party damage or damage to
other items caused by use of the product.
Door and Glass
Should there be any soot on the glass it may be
necessary to clean it. Use dedicated glass cleaner,
as other detergents may damage the glass. (NB! Be
careful, even dedicated glass cleaner can damage the
varnish on the door frame).
the glass is to use a damp cloth or kitchen roll paper
and apply some ash from the burn chamber. Rub
around the ash on the glass and finish off with a piece
of clean and damp kitchen roll paper. NB! Only clean
when the glass is cold.
GB
A good advice for cleaning
17