Page 1
710ST SMART TECHNOLOGY FLYWHEEL ELLIPTICAL TRAINER IMPORTANT: Read all instructions carefully before using this product. Retain this owner’s manual for future reference. The specifications of this product may vary from this photo and, subject to change without notice. OWNER’S MANUAL...
Page 2
PLEASE DO NOT RETURN THIS PRODUCT TO THE STORE. STOP. Contact customer service if you have any questions regarding assembly or proper operation of the machine. Email us at: Service@paradigmhw.com Or call us at: 1-844-641-7921 Hours: 8:00 am to 5:00 pm (PST) Daily...
SERVICE IMPORTANT: FOR NORTH AMERICA ONLY For damaged or defective product, questions, replacement parts or any other service support, please contact our customer service department by the below methods: For The Best Service, please Email: service@paradigmhw.com Response Time: 1-2 Business Days Emailing us with the information above will be the best method to receive a response during peak business hours Website:...
IMPORTANT SAFETY GUIDELINES Read all guidelines before using this machine. When using this machine, basic precautions should always be followed, including the following: WARNING - To reduce the risk of injury to persons: Make sure your equipment is correctly assembled before you use it. Be sure all screws, nuts, and bolts are tightened prior to use.
Page 7
IMPORTANT SAFETY GUIDELINES Do not use this equipment if you have any of the following conditions or ailments: Pregnancy Extreme obesity Middle ear infection Hiatus hernia or Ventral hernia Glaucoma, retinal detachment or conjunctivitis Use of anticoagulants including Aspirin in high doses.
PARTS LIST No. Description No. Description 25 Flat Washer Φ6 Main Frame 2R Right Foot Bar 26 Nylon Nut M6 27L Left Pedal Bolt φ16*88.5*L23 2L Left Foot Bar 27R Right Pedal Bolt φ16*88.5*L23 3L Left Handrail 28 Wave Washer φ28*φ17*0.3 3R Right Handrail 4L Left Handrail Arm Ф32*1.5 29 Bushing Ф24.5*Ф16*14...
Page 11
PARTS LIST No. Description No. Description 78 Flywheel Cover 53 Console 54 Curve Washer φ16*φ8 79 Nut M6 S10 55 Bottle Holder 80 Left Rear Frame Cover 81 U shape Bracket 31*30*δ1.0 56 Lower Hand Pulse wire 750mm 57 Handrail Arm Cap 82 Nut M10 58 Right Pedal 395*150*65 83 Eyebolt M6*36...
ASSEMBLY TOOL 6mm Allen Wrench 1PC Metal Tube Remove the Metal Tubes from the Main Frame (1) by using 6mm Allen Wrench provided. Discard the metal tubes and any hardware that was attached at this point as they will not be used in the actual assembly.
Page 14
ASSEMBLY TOOL Multi-Hex Wrench 1PC STEP 1 1A. Installing the Front Stabilizer – Lift up the front of the Main Frame (1) and align the holes of the Front Stabilizer (7) with the bracket holes on the Main Frame (1). Ensure that the wheels on the Front Stablizer End Cap (38) are facing outwards.
ASSEMBLY PRE-INSTALLED HARDWARE (13) Spring (45) Bolt Washer 8PCS 8PCS (54) Curve Washer 8PCS TOOL 6mm Allen Wrench 1PC MUST TIGHTEN IN SEQUENCE: A,B,C,D,E,F,G,H. STEP 2 2A. Removing The Hardware From The Front Post – Use the 6mm Allen Wrench to remove eight Bolts (45), eight Spring Washers (13), and eight Curve Washers (54) from the Main Frame (1).
ASSEMBLY TOOL PRE-INSTALLED HARDWARE (13) Spring (14) (62) D Washer (45) Hex Bolt Washer Flat Washer 2PCS 2PCS 6mm Allen Wrench 1PC 2PCS 2 PCS STEP 3 Installing Bushings – Attach two Bushings (46) onto the rods coming out from the Front Post (5).
Page 17
ASSEMBLY TOOLS 8mm Allen Wrench Multi-Hex Wrench STEP 4 4A. Left Foot Bar Installation – Insert the Left Pedal Bolt (27L) along with a Wave Washer (28) through the U Shaped Bracket (37) located on the back of the Left Foot Bar (2L). Secure the Left Pedal Bolt (27L) to the Left Crank (43) by turning the Left Pedal Bolt (27L) COUNTER-CLOCKWISE.
Page 18
ASSEMBLY Figure B NOTE: Look to Fig. B for the correct installation of the Pedal Bolts. Keep the bolt perfectly straight when the bolt goes through the Foot Bars, and is being screwed into the Crank correctly. If the bolt is screwed into the crank at an angle, this may damage the equipment.
Page 19
ASSEMBLY TOOL Multi-Hex Wrench 1PC STEP 5 5A. Left Pedal Installation – Install the Left Pedal (24) onto the Left Foot Bar (2L) using three Bolts (23), three Flat Washers (25) and three Nylon Nuts (26). Tighten the Nylon Nuts (26) using the Multi Hex Wrench provided.
Page 20
ASSEMBLY TOOL Multi-Hex Wrench 1PC STEP 6 6A. Installing the Left Handrail Arm – Insert the Left Handrail Arm (4L) onto the Left Handrail (3L) using two Carriage Bolts (64), two Curve Washers (63) and two Nylon Nuts (26). Tighten the Nylon Nuts (26) using the Multi Hex Wrench provided.
Page 21
ASSEMBLY PRE-INSTALLED HARDWARE TOOL (13) Spring (45) Hex Bolt (54) Curve Washer 6mm Allen Wrench 1PC Washer 2PCS 2PCS 2PCS STEP 7 7A. Removing The Hardware From The Front Post – Remove two Bolts (45), two Spring Washers (13), and two Curve Washers (54) from the Front Post (5). 7B.
ASSEMBLY Install tip: Ensure the ledge of part (50) is installed towards the user with the ledge upright. TOOL Multi Hex Tool with Phillips Screwdriver 1PC STEP 8 8A. Installing the Left Handrail Cover – Install the Front Left Handrail Cover (10L) and the Rear Left Handrail Cover (11L) around the Left Handrail (3L) with two Self-Tapping Phillips Screws (65) and two Self-Tapping Phillips Screws (9) using the Multi-Hex Tool with Phillips Screwdriver provided.
Page 23
ASSEMBLY TOOL Multi Hex Tool with Phillips Screwdriver 1PC STEP 9 9A. Installing The Left Foot Bar Cover – Install the Left Foot Bar Cover (22L) and Right Foot Bar Cover (22R) onto the Left Foot Bar (2L) with two Self-Tapping Phillips Screws (65) and one Self-Tapping Phillips Screw (9) using the Multi-Hex Tool with Phillips Screwdriver provided.
Page 24
ASSEMBLY Figure D TOOL PRE-INSTALLED HARDWARE Multi Hex Tool with Phillips Screwdriver 1PC (21) Self-Tapping Phillips Screw 2PCS (52) Phillips Screw 4PCS STEP 10 10A. Removing Hardware From The Console – Remove four Phillips Screws (52) from the back of the Console (53). 10B.
Page 25
ASSEMBLY STEP 11 – 11A. Plugging In The Machine Connect the AC Adaptor (48) to the AC Cable Plug (101) on the rear of the Left Cover (92). WARNING: This Console Is Not Battery Operated. Use The Adaptor Provided To Power The Console.
CONSOLE Display Information: TIME----------------------------------------------------- 00:00-99:00 SPEED ------------------------------------------------- 0.0-99.9 MPH / KM DISTANCE (DIST) ----------------------------------- 0.0-999.9 ML CALORIES (CAL) ------------------------------------ 0.0-999.9 CAL ODOMETER (ODO) --------------------------------- 0-999.9 ML CONSOLE BUTTONS: Start/Stop Button: Starts and pauses workouts. Hold for 5 seconds to reset console. Mode Button: Switches displayed workout values: MPH/KMPH DIST...
Page 28
CONSOLE Workout Program: Challenge yourself with one of the 21 preset workout programs. 1. Pressing the MODE button at the user selection screen will take you into the PROGRAM workout menu using the selected user profile. ˄ ˅ 2. Use the buttons to scroll through the workout programs.
TRANSPORTATION Transporting the Elliptical Hold the Handlebar (6) and lift up the machine until the wheels on the Front Stabilizer End Caps (38) make contact with the floor. Push or pull the unit to the desired location, then gently lower the machine and Rear Stabilizer (8) until it makes contact with the ground.
TROUBLESHOOTING & MAINTENANCE TROUBLESHOOTING PROBLEM: The elliptical wobbles when in use. SOLUTION: Turn the Rear Stabilizer End Cap (44) on the Rear Stabilizer (8) as needed to level the elliptical. PROBLEM: The Console (53) does not turn on. SOLUTION: Remove the Console (53) and verify that ALL wires that come from the Console (53) are properly connected to the wires that come from the Front Post (5).
WARRANTY MANUFACTURER’S LIMITED WARRANTY Paradigm Health & Wellness warrants to the original purchaser that this product is free from defects in material and workmanship when used for the purpose intended, under the conditions that it has been installed and operated in accordance with Paradigm’s Owner’s Manual.
PARTS REQUEST FORM Paradigm Health & Wellness, Inc. EMAIL THIS FORM WITH YOUR RECEIPT OF PURCHASE TO Service@paradigmhw.com NAME:_____________________________________________________________________________________ ADDRESS:__________________________________________________________________________________ CITY:________________________ STATE:_____________ ZIP:_______________________________________ TELEPHONE: (Day)______________________________________________________________________ (Night)_____________________________________________________________________ SERIAL#:___________________________________________________________________________________ MODEL#:___________________________________________________________________________________ PURCHASE DATE:___________________________________________________________________________ PLACE OF PURCHASE:_______________________________________________________________________ PART # DESCRIPTION “YOUR ORDER WILL BE PROCESSED WITHIN 3 BUSINESS DAYS” This form can also be faxed to #: 626-810-2166...