Setting The Weekly Timer To Real Time; Programming The Timer; Programování Casovace - Harvia C260 Manual

EN
2.2.2.Setting the Weekly Timer to Real
Time
keep the [clock] -button in the down
•
position the whole time.
press the hours button [h+] to set the
•
time.
A single push on the [h+] -button
•
moves the setting on one hour at a
time; holding the button in continuously
speeds up the process.
Holding in the [h+] -button continuously
•
will cause the hours to appear in the
following rotational series:
00 ... 23 ... 00 or
AM 00 ... AM 12 ... AM 00/
PM 00 ... PM 12 ... PM 00,
depending on the screen display mode
selected. (Fig. 5)
Please Note! During summer time real
•
time is set by pressing the [± 1 h]
one hour for ward. The reverse
process applies for winter time.
press the [m+] -button for the
•
minutes setting. A single push moves
the setting on one minute at a time;
holding the button in continuously
speeds up the process. (Fig. 6)
Setting the minutes will not affect the
•
hours setting, even if the number of
minutes registered in the screen
exceeds 59.
press the [day] -button to set the right
•
day in the screen. Monday is no. 1,
Tuesday no.2, etc.
press the [± 1h] -button in summer
•
for the summer time symbol to appear
in the screen. The hours setting will
simultaneously advance by one hour.
release the [clock] -button
•

2.2.3. Programming the Timer

Heater On
press the [Ch] -program button once;
•
the screen will appear as in the
diagram. (Fig. 7)
using the [manual] -button press
•
symbol to activate programming mode
in the screen as in the diagram. A dark
speck in the arc indicates that the
heater is programmed to come on at
the desired time. (Fig. 8)
If you forget to press the programming
•
symbol, it begins to flash when you try
to reconfirm and enter the program
time with the [Ch] -button.
press [h+] -button to set desired hour
•
for system to come on
press [m+] -button to set desired
•
minute for system to come on
press [day] -button to set desired day
•
of the week for system to come on
(Fig. 9)
6
CZ
2.2.2. Nastaveni tydenniho casovace do
Tlacítky [h +] a [H ÿ ] nastahujete celé hodiny.
Pokud podržíte tlacítko [h +] zpusobí to, že
se budou zobrazovat serie pro nastavení
00 ... 23 ... 00 nebo
PM 00 ... PM 12 ... AM 00 /
AM 00 ... AM 12 ... AM 00,
V závislosti na režimu zobrazení obrazovky. (Obr. 5)
• Upozornení! Pro nastavení letního a zimního casu
se používá tlacítko [± 1 h]
• Tlacítkem [m+ ] se nastavují minuty . (Obr. 6)
Nastavení celých hodin se nezmení i
Figure 5.
pokud preskocíte 59 minut.
0brazek 5.
• Stiskem tlacítka [den] nastavujete dny v týdnu
Pondelí je 1, Úterý je 2, atd.
Figure 6.
0brazek 6.
2.2.3. Programovani casovace
Figure 7.
Spinani kamen
0brazek 7.
Stisknete \[Ch] program jednou tlacítko;
Objeví se obrazovka (Obr. 7)
• pomocí tlacítka \[manuál] aktivujeme
nastavený režim
Tmavá teckou v oblouku vyplývá, že
ohrívac je naprogramován tak, aby sepl
v požadovanou dobu. (Obr. 8)
• Pokud zacne tecka blikat zmácknete tlacítko
Figure 8.
\[Ch]button.
0brazek 8.
• stisknte \[h +]tlacítko pro nastavení
požadované hodiny.
• stisknte \[m +]tlacítko pro nastavení
požadovanych
minut pro systém prijde na
• stisknte \[den]tlaítko nastavíte
požadovaný denv týdnu. (Obr. 9)
Figure 9.
0brazek 9.
do realneho rezimu.