Related Manuals for REMKO Allmat
Summary of Contents for REMKO Allmat
- Page 1 REMKO Allmat Automatic Slow Combustion Heater Operation Technology Spare Parts REMKO – powerful like a bear. Edition GB – M04...
-
Page 3: Table Of Contents
Our guarantee will become void when the unit supplied by us is used and installed for inadequate purposes, or maintained incorrectly, etc., or if it is changed without our prior consent. Subject to alterations! Stationery slow combustion heater REMKO Allmat Contents Contents Page Page... -
Page 4: Safety Instructions
The blow-out grille may not be closed. ◊ The fire and furnace door must be shut after the unit The REMKO ALLMAT works on the principle of sub- is warmed up and during operation. heating using exhaust post-combustion. The feeder ◊... -
Page 5: Fuels
Wood, dry Peat, pressed BIMATIK Heat Output Regulator. Lignite briquettes The REMKO ALLMAT is equipped with a BIMATIK ther- mal output regulator. Coke This automatically regulates the heat output that has Anthracite been set on the regulator knob in the “min / max” area. -
Page 6: Installation
Installation The exhaust connection may only be used with ap- The unit may only be installed in accordance with the proved chimneys. The chimneys can be made of bricks applicable legal regulations and the ordinance on heat- or metal. If the chimney is made of brick, make sure ing systems. -
Page 7: Bimatik
0,3 mbar / 3 mm WS Connection Ø 150 mm EDV-NO. 1034250 AS-1000-D When using the chimney draught stabiliser, the ex- haust flap on the ALLMAT must be opened all the way. The draught regulator is set using a draught AS-ÜE-D gauge! AS-500-E AS-T90-D AS-RB90-E... -
Page 8: Starting
Starting Heating Mode 1. Fill up the feeder chute completely once approx. 50% Important hints about operating the unit for the first of the fuel from the pre-fuelling process is burning. time! 2. Adjust the primary air slide plate in increments to Because burned refractory bricks also contain residual the appropriate setting for the fuel. -
Page 9: Troubleshooting
Troubleshooting Maintenance and Service Prior to starting any work make sure to pull the Regular maintenance and observance of some basic mains plug out of the mains socket! principles are required to ensure a long service life and to keep the unit functioning properly. The unit is generating too much heat or is overheated. -
Page 10: Exploded View
Exploded View Front view without front door Back view without rear plate A = Mount for fan thermostat B = Mount for BIMATIK temperature sensor Side view – sectional drawing We reserve the right to make modifications in dimensions and construction in the interests of technical progress. -
Page 11: Spare Part List
Gasket (filling flap) 1104036 Magnetic lock (front door) 1104015 Thermostat cable 1104084 Connecting cable with plug 1101320 Lever ashpan 1104056 Pokers 1104086 Cleaning brush for heat-exchanger pipes 1104087 Chimney draught regulator for chimney installation 1007661 REMKO chimney draught stabiliser 1034250... -
Page 12: Technical Data
“guarantee certificate” which is we will not be held responsible and our guarantee will enclosed with every REMKO-heater and has returned it become void. to REMKO GmbH & Co. KG in due time after the unit’s sale and commissioning. -
Page 13: Heating Adjacent Rooms
Heating Adjacent Rooms The unit may only be installed within fire-resistant, non-flammable walls! Make sure that the air follows a straight path without curves. Flexible or stationary warm air channel Heat distributor flap Replace the existing cover with a cover with connections. Replace the existing adjustable blow-out grille with an adjust- able one that can be closed. -
Page 14: Arrangement Of Refractory Lining
Arrangement of Refractory Lining Fig. Nr. 33 EDV-Nr. 1108300 Fig. Nr. 25 EDV-Nr. 1108304... - Page 16 REMKO GmbH & Co. KG Klima- und Wärmetechnik D-32791 Lage Im Seelenkamp 12 • D-32777 Lage PO Box 1827 • Phone +49 (5232) 606 - 0 +49 (5232) 606260...