REMKO ATK 25 Operation,Technology,Spare Parts
Automatic oil heater with built-in oil burner, tank and exhaust gas connection
Hide thumbs
Also See for ATK 25:
- Operation, technology and spare parts (16 pages) ,
- Operating and installation (20 pages)
Related Manuals for REMKO ATK 25
Summary of Contents for REMKO ATK 25
- Page 1 REMKO ATK 25 Automatic oil heater with built-in oil burner, tank and exhaust gas connection Operation · Technology · Spare Parts Edition GB-D05...
-
Page 3: Table Of Contents
Contents Safety Notices Environmental Protection and Recycling Device Description Regulations for air heaters Mounting Regulations Exhaust gas routing Commissioning Decommissioning Maintenance and Care 10-12 Exhaust gas analysis Fuel pump Customer Service and Guarantee Intended use Electrical Wiring Diagram Trouble Shooting Exploded view Spare Parts List Maintenance log... -
Page 4: Safety Notices
REMKO ATK Environmental Safety Notices Protection and When using the appliance, always observe the respective local construc- Recycling tion and fire protection ordinances as well as the regulations of the employers‘ liability insurance associations. The appliances were subjected to The unit may be set up and Disposal of packaging ■... -
Page 5: Device Description
Description of Device The unit is fired directly with Working of Device Safety temperature limiter heating oil EL or diesel and can (STB) be operated with or without an When the power plug is connected exhaust-gas connection. to a power socket, the automatic The STB interrupts the supply It is intended for mobile and fully tank heater is activated for tempe-... -
Page 6: Regulations For Air Heaters
REMKO ATK Provision for Air Heaters A natural air supply sufficient exhaust gases through exhaust When using the units, the respec- for the combustion is present gas ducting to the outside. tive applicable guidelines must always be observed. if e.g. -
Page 7: Mounting Regulations
Mounting Regulations When the unit is in use, the safety CAUTION guidelines of the employers‘ liability Installation in closed, well The units must only be in- insurance associations, the respective aerated rooms without stalled in well ventilated connection to a chimney country construction ordinances, and spaces and not in living areas the burning appliance regulations... -
Page 8: Exhaust Gas Routing
REMKO ATK Exhaust system In the outdoors or in open rooms, Malfunction-free operation is All exhaust-pipe parts must be ■ ■ the operation of the device is guaranteed if the exhaust attached reliably. Their diameter also possible without an exhaust... -
Page 9: Commissioning
Commissioning Prior the commissioning the unit Paraffin accumulation by low Connect the unit with the is to be checked to make sure that outside temperatures. current supply there are no visible defects on the control and safety devices, that the The supply of sufficient liquid fuel unit has been installed correctly is to be ensured, even with low... -
Page 10: Decommissioning
REMKO ATK Maintenance and Shut-Down Service heating with room thermostat (accessories) 1. Set the operating The unit is to be maintained regu- switch to “0” (OFF). larly whereby some fundamental The unit runs fully automatically rules are to be observed to ensure... - Page 11 Empty fuel tank at least twice a Cleaning the burner ■ year and rinse it with clean fuel Do not use water! Clean the components of the burner as described below: Keep burner head clean ■ Wearing parts such as e.g. oil ■...
-
Page 12: Exhaust Gas Analysis
REMKO ATK Exhaust Measurement Adjusting the air slide plate If the main filter frequently On account of the construction- ■ becomes dirty dependent design of the exhaust The air slide plate is set at the connection (connection nozzle factory. The air throughput may... -
Page 13: Fuel Pump
Fuel Pump The standard type of the pump Setting the pump pressure Cleaning the cartridge filter runs in a system of 1 pipe. The required fuel is sucked in The pump pressure can Regularly clean the cartridge filter through the suction line „S“. only be set if a manometer [B] of the fuel pump and replace it is connected to the connection [P]. -
Page 14: Customer Service And Guarantee
REMKO GmbH & mercial use (no private living area permitted. Co. KG in a timely manner after heating). -
Page 15: Troubleshooting
Troubleshooting Trouble: Cause: Fan motor does not start 2 – 3 – 4 – 6 – 7 – 8 – 25 Fan motor is running but burner will not be ignited. 1 – 5 – 6 – 9 – 10 – 11 – 12 – 13 – 14 – 15 – 16 – 17 Unit shut down without flaming formation. -
Page 16: Exploded View
REMKO ATK Exploded View We reserve the right to make modifications in dimensions and construction in the interests of technical progress. -
Page 17: Spare Parts List
Spare Part List Description EDP-No. Description EDP-No. Exhaust connection 1103702 Side cover, left 1103772 Inspection cover 1103740 Retaining ring 1101622 Inspection cover 1103703 Wheel cap 1101623 Gasket (inspection cover) 1103705 Transport handle, front 1102932 Combustion chamber cpl. 1103728 Wheel 1102155 Air slide plate 1103729 Fuel tank... -
Page 18: Maintenance Log
REMKO ATK ✍ Maintenance log Model ........Model No........10 11 12 13 14 15 16 17 18 19 20 Clean unit – surface – Clean unit – interior – Clean fan blade Clean fan housing Clean condenser Clean evaporator... -
Page 19: Technical Data
Technical Data Model ATK 25 25,00 Nominal heat output max. Nominal heat output 22,50 Air output 1080 Increase of temperature Δ Fuel Heating oil EL or Diesel Fuel consumption, max. 2,45 Nozzle (Danfoss) 80° H 0,50 Pump pressure approx. 11 to 12 Tank capacity Ltr. - Page 20 Customer Care is on the job. REMKO Our extensive network of experienced dealers guarantees you constant, short- term, and reliable service. REMKO GmbH & Co. KG Air conditioning and heating technology Im Seelenkamp 12 D-32791 Lage Postfach 1827 D-32777 Lage...