Related Manuals for REMKO ATK 50-S
Summary of Contents for REMKO ATK 50-S
- Page 1 REMKO ATK 50-S Automatic oil heater with built-in oil burner, tank and exhaust gas connection Operation · Technology · Spare parts Edition GB-I02...
-
Page 3: Table Of Contents
Contents Safety notes Environmental protection and recycling Unit description Installation instructions Exhaust gas routing Transport Commissioning Shutdown Care and maintenance 9-11 Exploded view of the unit Spare parts list Troubleshooting Technical data Electrical wiring diagram Carefully read this operating manual prior to commissioning or using the units! This manual is an integral part of the unit and must always be kept in the vicinity of the installation location or on... -
Page 4: Safety Notes
REMKO ATK Environmental Safety notes protection and Always observe the respective local building code and fire prevention recycling guidelines as well as the guidelines of the accident prevention and insurance associations when using the equipment. Disposing of packaging The units have been subjected... -
Page 5: Unit Description
Unit description The units are portable, directly Operating sequence Safety temperature limiter fired fan-assisted heaters (WLE) (STB) with heat exchanger and exhaust The supply air fan switches on gas connections exclusively for once the units are switched on in The heating function is commercial applications. -
Page 6: Installation Instructions
REMKO ATK Installation instructions Installation in enclosed, well Safety distances The safety regulations of the accident ventilated areas without prevention and insurance associations, exhaust gas connection the respective regional building In order to guarantee safe ■ regulations and the combustion... -
Page 7: Exhaust Gas Routing
Exhaust gas routing Transport It is also possible to operate The units can be transport in their the units outdoors or in open normal operating position or in a spaces without exhaust routing. vertical position to save space. We always recommend fitting Proceed as follows for a vertical an exhaust gas duct with a rain position:... -
Page 8: Commissioning
REMKO ATK Commissioning The units must be checked Paraffin formation with low Connecting the units to for visible defects on the outside temperatures. the electrical power supply operating and safety devices as well as proper installation and Even at low temperatures, an 1. -
Page 9: Shutdown
Care and maintenance Heating with room thermostat Heating without room Regular care and observation thermostat of some basic requirements will The units operate fully ensure trouble-free operation and automatically and according The units operate a long service life of the units. to the room temperature. - Page 10 REMKO ATK Use only clean EL heating oil or Proceed as follows to clean the fuel Maintaining the burner ■ diesel fuel. Beware of paraffin tank: formation! Clean the burner components as described: Keep the burner head clean ■ Wear parts such as the oil ■...
- Page 11 Setting the ignition electrodes Setting the pump pressure 2 - 3 The pump pressure may only be set and/or modified when a suitable oil pressure gauge is connected to the connection [P]. The pump pressure is modified by turning the pressure adjustment screw [A]: Clockwise: All sizes are approximate values and are in mm.
-
Page 12: Exploded View Of The Unit
REMKO ATK Exploded view of the unit We reserve the right to modify the dimensions and design as part of the ongoing technical development process. -
Page 13: Spare Parts List
Spare parts list Designation EDP no. Designation EDP no. Fuel tank 1103965 Terminal strip 1103781 Carrier housing 1103966 Mounting 1103782 OV mounting 1103967 Auxiliary relay 1107375 Steel tubular frame 1103968 O-ring 1103783 Locking ring 1101622 Ignition cable 1107137 Hubcap 1101623 6 A fuse 1103785 Oil pre-heater... -
Page 14: Troubleshooting
REMKO ATK Troubleshooting Malfunctions Cause: The supply air fan does not start. 2 – 3 – 4 – 6 – 7 – 8 – 25 The supply air fan runs but the burner does not ignite. 1 – 5 – 6 – 9 – 10 – 11 – 12 – 13 – 14 – 15 – 16 – 17 The unit malfunctions without generating a flame. -
Page 15: Technical Data
Technical data Series ATK 50-S Nominal heat load max. Nominal heat capacity 43.5 Air volume 2400 Temperature increase ∆ Fuel Heating oil EL in accordance with DIN 51603-1 or diesel fuel Max. fuel consumption Nozzle (DELAVAN) 80° W Pump pressure, approx. - Page 16 This has given us the reputation of being more than just an excellent, reliable supplier: REMKO, a partner who helps to solve problems. Sales REMKO offers not just a well- established sales network both...