Safety Warnings; General Instructions; General Safety Precautions; Applications And Technical - Homa Saniquick II-UF Series Installation And Operation Instruction Manual

2. Safety Warnings

2.1. General Instructions

Signs used to mark instructions in this manual
Safety instructions in these operating instructions,
which, if not observed, could cause a danger for persons
are marked with the general symbol in accordance with
DIN 4844-W 9.
Warnings against electrical voltage are marked with
the safety symbol in accordance with DIN 4844-W 8.

2.2. General Safety Precautions

General regulations and guidelines not mentioned in the
safety warnings retain their validity.
These operating instructions contain basic instruc-
tions, which have to be adhered to during installation, op-
eration and maintenance. These operating instructions
must be read from mechanic and the operator before in-
stallation and operation of the pump and have to be kept
available at the operating place of the machine/unit at all
times. Persons who are not familiar with the operating
instructions shall not use this product.
Children and adolescents under age 16 shall not use
the unit and must keep away from the machine/unit
while it is operational.
The unit must be installed from a technical experi-
enced plumber.
Never work alone.
Please make sure that used aids e.g.hoisting crane
are in regular and reliable contiditions.
The working area has to be closed off expediently
and must adhere to local workplace regulations.
Always use personal safety equipment such as safety
boots, rubber gloves, safety glasses and helmet.
Make sure that the emergency exit from the work-
place is not barricaded.
To prevent suffocation and poisoning caused by
venomous gases, make sure that enough oxygen exists
at the workplace.
If you have to work with welding tools or electric tools,
make sure that there is no explosion hazard.
Immediately after repair or maintenance work, all
safety and protection equipment must be reinstalled and
placed in function again.
The operator of the pump is responsible for third
parties within the work area.
All other rules and regulations and local codes cover-
ing health and safety must be observed. In accordance
with product liability law, we point out that we shall not be
liable for damages caused by the pump due to non-
observance of the instructions and guidelines set forth in
the operating instructions. The same product liability are
valid for accessories.
3. Applications and Technical Description

3.1. Applications

The pump station Saniquick II-UF is used for removal of
clear water and waste water from hand basins, washing
machines, showers or bath and cellar de-watering in
rooms below the sewer level (For pumping of sewage wa-
ter we recommend our lifting station Sanistar II).

3.2. Product Description

The pump station for under-floor installation consists of
a collecting tank fixed to prevent lifting, one or two pumps,
3 inlets DN 100, a connecting piece DN 70 for air vent and
cable duct. The frame with adjustable height to adapt the
cover plate to the floor level is odour tight.
The pumps must not be used for pumping of liquids
containing great quantities of abrasive solids, like sand
or stones.
Before pumping of chemically aggressive liquids, the
resistance of the pump materials must be checked. The
automatic float switch start and stop the pumps auto-
matically according to the liquid level in the tank
automatically.
The installation kit consists of a discharge connector, a
pipe and a non-return valve.

3.3. Technical Data

Inlet
Connection for aurvent, cable duct
Discharge
Tank volume
Insulation class
Motor protection
Speed
Applicable pump models
Pump type Motor-
input (kW)
C 225 WA 0,25
C 235 WA 0,35
C 280 WA 1,00
C 290 WBA 1,20
C 290 DA 1,10
CR 250 WA 0,55
H 501 WA 1,20
H 502 WA 1,20
H 502 DA 1,00
H 505 WA 1,50
H 506 WA 1,50
H 1506 DA 1,30

3.4. Operation Conditions

Please pay attention to the installation and operation
instruction manual of the installed submersible pump.
3.5. Explosive Environments
For operation of the pumps in explosive environments
only models with explosion-proof motors (Ex model) must
be used.
For each individual installation the explosion classifi-
cation (Ex-class) of the pump must be approved by the
localauthorities.
9
3 x DN 100
DN 70
BSP 1¼" M
40 l
F
IP 68
2.900 rpm
Voltage Nominal
50 Hz (V) current (A)
230-240/1Ph 1,4
230-240/1Ph 1,8
230-240/1Ph 4,5
230-240/1Ph 5,0
400-415/3Ph 2,0
230-240/1Ph 2,1
230-240/1Ph 5,0
230-240/1Ph 5,0
400-415/3Ph 2,0
230-240/1Ph 6,9
230-240/1Ph 6,9
400-415/3Ph 2,4
Weight
(kg)
4,1
4,6
8,0
8,3
8,3
4,2
9,0
9,0
9,0
11,0
11,0
11,0