M1400 About the Hardware The parallel module M1400 is an input / output module used in the II/O system. There are 32 Standard 24 V inputs / outputs, which achieve 4 ports of 8 bit each. These 4 ports ( D0..D3 ) correspond to the data bytes in the FO transmissions protocol and according to the way they are to be used, they can be configured as input or output.
Page 4
M1400 Parallel Input / Output Beckhoff II/O-System Basic Circuit Diagram Page 4 of 16 Version : 2.0 Date : 26.7.94...
M1400 Parallel Input / Output Beckhoff II/O-System 3. Technical Data Inputs / Outputs 32, can be configured for each port; state of all inputs / outputs LED shows 24 VDC, 10 mA, digital filter input specifications input switching voltages 0 - 8V...
DIN EN 50022 or DIN EN 50035. Configuration Each I/Oport of the M1400 can be configured as input or as output. This does not dependent on the configuration of the other ports. There are DIP switches under the XILINX board of the M1400.
Page 8
M1400 Parallel Input / Output Beckhoff II/O-System View under the M1400 XILINX board The following module configuration is possible by setting jumpers 1 to 3 : Watchdog on / off Jumper 1 for Port D0 and D1 If this jumper is set the ’Watchdog’ function is switched off.
Page 9
M1400 Parallel Input /Output Beckhoff II/O-System The following modul configuration is possible by setting jumpers 4 to 7 : Fast Inputs M1400 (Interrupt Inputs) Fast input II3 : Jumper 4 If jumper connection betwenn port D0.3 and XILINX II3 is...
Page 10
M1400 Parallel Input / Output Beckhoff II/O-System Page 10 of 16 Version : 2.0 Date : 26.7.94...
M1400 Parallel Input /Output Beckhoff II/O-System 5. Table of Connections Connector pin assignment with Signal Description CONNECTOR X10 Connector Signal Description +24V control power supply GND ground CONNECTOR X20 Connector Signal Description +24V supply for output +24V supply for output D0.0...
Page 12
M1400 Parallel Input / Output Beckhoff II/O-System continuation connector X20: Connector Signal Description Bit 6 of Data byte 0 D0.6 D0.6 is output, if DIL switch S1 = ON D0.6 is input, if DIL switch S1 = OFF D0.7 Bit 7 of Data byte 0 D0.7 is output,...
Page 13
M1400 Parallel Input /Output Beckhoff II/O-System CONNECTOR X21 Connector Signal Description +24V supply inputs +24V supply inputs +24V power supply for input 0.0 +24V +24V +24V power supply for input 0.1 +24V +24V power supply for input 0.2 +24V +24V power supply for input 0.3 +24V power supply for input 0.4...
Page 14
M1400 Parallel Input / Output Beckhoff II/O-System CONNECTOR X30 Connector Signal Description +24V supply for output +24V supply for output Bit 0 of Data byte 2 D2.0 D2.0 is output, if DIL switch S1 = ON D2.0 is input, if DIL switch S1 = OFF Bit 1 of Data byte 2 D2.1...
Page 15
M1400 Parallel Input /Output Beckhoff II/O-System continuation connector X30: D3.0 Bit 0 of Data byte 3 D3.0 is output, if DIL switch S1 = ON D3.0 is input, if DIL switch S1 = OFF D3.1 Bit 1 of Data byte 3 D3.1 is output,...
Page 16
M1400 Parallel Input / Output Beckhoff II/O-System CONNECTOR X31 Connector Signal Description +24V supply outputs +24V supply outputs +24V power supply for input 2.0 +24V +24V +24V power supply for input 2.1 +24V +24V power supply for input 2.2 +24V +24V power supply for input 2.3...
Need help?
Do you have a question about the M1400 and is the answer not in the manual?
Questions and answers