Thank you for purchasing a TERBLY product. You have acquired a powerful and versatile fixture. We are confident that you will be satisfied with our excellent products and service. For your own safety, please read this user manual carefully before installing and operating the device.
Make sure that the available voltage is not higher than that which is stated at the end of this manual. Make sure the power cord is never crushed or damaged by sharp edges. Should the power cord suffer If this should be the case, replacement of the cable must be done by an LPAR7QZ User Manual XM1334-V1.2-B...
Page 4
When powered on for the first time, some smoke or smell may occur. This is caused by coating on metal parts when heated and is normal. If you are concerned, please contact your distributor or Terbly. Do not focus the beam onto flammable surfaces. The minimum distance between the exiting lens of the device and the illuminated surface must be greater than 0.5 meter.
Upgrades: fast and convenient through DMX cable Reset DMX address, remote lamp switch, reset can all be done by the controller Running time of fixture on display for reference Advanced RDM function WHIGHT Net weight: 6.8 kg LPAR7QZ User Manual XM1334-V1.2-B...
Page 6
PHOTOMETRIC DATA IMAGE DMX CHANNEL DATA IMAGE LPAR7QZ User Manual XM1334-V1.2-B...
Improper installation/ rigging can result in serious bodily injury. Before rigging make sure that the installation area can hold a minimum point load of 10 times the device’s weight. LPAR7QZ User Manual XM1334-V1.2-B...
Page 10
Be sure this fixture is kept at least 0.1m away from any flammable materials (decoration etc.). Important: This step is very important to ensure safe rigging of the fixture. LPAR7QZ User Manual XM1334-V1.2-B...
Page 11
If you lack these qualifications, do not attempt the rigging of this device yourself. Improper installation/ rigging can result in serious bodily injury. LPAR7QZ User Manual XM1334-V1.2-B...
Page 12
Install the frost filter holder .Fix the 4pcs M4x8 screws .See Picture Please install the frost filter holder as the direction of arrow in picture .Clamp it with scrollbar. Install barn-door. Fix it with M3x6 screws . LPAR7QZ User Manual XM1334-V1.2-B...
The DMX terminator is an XLR plug with a 120 resistor connected between pins 2 and 3,which is then plugged into the output (female) XLR socket of the last fixture in the chain. Please see illustrations below. LPAR7QZ User Manual XM1334-V1.2-B...
60 seconds after the last keypress. Press this key under edit mode, you can choose the function you want from the top down in the Mode/Esc. [ENTER] this key is functionless when in normal mode. Press this key under the edit mode, it will enter into next Mode/Esc. LPAR7QZ User Manual XM1334-V1.2-B...
Page 15
Auto =XXX Test Manual Adjust Fine adjustment of the led Password Calibrat Red… Zoom ProPart1 Prog 1 ~ 10 EditProg Sel Prog ProPart2 Prog 1 ~ 10 Select programs to be run ProPart3 Prog 1 ~ 10 LPAR7QZ User Manual XM1334-V1.2-B...
Page 16
“Select program”. You can set the number of steps under “Edit program”. You can edit the individual scenes under “Edit scenes”. With this function, you can run the individual scenes either automatically, i.e. with the adjusted Step-Time. LPAR7QZ User Manual XM1334-V1.2-B...
Page 17
5. Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu. 9.4.2. Serv set Password——The Password for this function is “50”. UID—— With this function you can call up various submenus via RDM. LPAR7QZ User Manual XM1334-V1.2-B...
Page 18
5 Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu. 9.4.6. InitStart 1 Access the main menu. 2 Press <Up/Down>, the display will show “InitStart”. 3 Press< ENTER>, the display will show “InitStart”. LPAR7QZ User Manual XM1334-V1.2-B...
Page 19
1 Access the main menu. 2 Press <Up/Down>, the display will show“Adjust”. 3 Press< ENTER>, the display will show“Adjust”. 4 The display show“Test Manual”. 5 Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu. LPAR7QZ User Manual XM1334-V1.2-B...
Page 20
Program 2, Part 2 uses Program 4, Part 3 uses Program 6, Assume: Program 2 includes scene of 10, 11, 12, 13; Program 4 includes scene of 8, 9, 10; Program 6 includes scene of 12, 13, 14, 15; Then it will run as below. Example LPAR7QZ User Manual XM1334-V1.2-B...
Page 21
5. Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu. TimePass With this function, you can display the timer password. 1. Access the main menu. 2. Press <Up/Down>, the display will show “TimePass”. 3. Press< ENTER>, the display will show“TimePass”. The time password is 038. LPAR7QZ User Manual XM1334-V1.2-B...
Blue LED -all arrays : 0-255 Blue ( 0-Black , 255-100% Blue ) White LED -all arrays : 0-255 White ( 0-Black , 255-100% White ) Red LED1 : 0-255 Red ( 0-Black , 255-100% Red ) Green LED1 LPAR7QZ User Manual XM1334-V1.2-B...
Page 23
Deep Blue 88--94 Just Blue 95--101 Medium Blue 102--108 Double CT Blue 109--115 State Blue 116--122 Full CT Blue 123--129 Half CT Blue 130--136 Steel Blue 137--143 Lighter Blue 144--150 Light Blue 151--157 Medium Blue Green LPAR7QZ User Manual XM1334-V1.2-B...
4) The power supply cables must not show any damage, material fatigue or sediment. Further instructions depending on the installation location and usage have to be adhered to by a qualified installer and any safety concerns have to be removed. LPAR7QZ User Manual XM1334-V1.2-B...
Please refer to the instructions under “Installation instructions”. Should you need any spare parts, please order genuine parts from your local dealer. 12. SERVICE For all service needs please contact your local authorized dealer or Terbly directly. Our contact details are: Email: QA@terbly.com...