Thank you for purchasing a TERBLY product. You have acquired a powerful and versatile fixture. We are confident that you will be satisfied with our excellent products and service. For your own safety, please read this user manual carefully before installing and operating the device.
Make sure the power cord is never crushed or damaged by sharp edges. Should the power cord suffer If this should be the case, replacement of the cable must be done by an TP02-CW,WW User Manual XM1268/1257-V1.0-NR...
Page 4
When powered on for the first time, some smoke or smell may occur. This is caused by coating on metal parts when heated and is normal. If you are concerned, please contact your distributor or Terbly. Do not focus the beam onto flammable surfaces. The minimum distance between the exiting lens of the device and the illuminated surface must be greater than 0.1 meter.
400W (Available external Power Consumption 400W (Available for external battery) battery) Input Voltage AC 100-240V,50/60Hz AC 100-240V,50/60Hz Net weight 15 kg 15 kg Hanging Type Pole-control Yoke, Manual Rocker Pole-control Yoke, Manual Rocker PHOTOMETRIC DATA IMAGE TP02-CW,WW User Manual XM1268/1257-V1.0-NR...
Page 6
DMX CHANNEL DATA IMAGE TP02-CW,WW User Manual XM1268/1257-V1.0-NR...
Improper installation/ rigging can result in serious bodily injury. Before rigging make sure that the installation area can hold a minimum point load of 10 times the device’s weight. TP02-CW,WW User Manual XM1268/1257-V1.0-NR...
Page 9
When clamp mounting; always use and install the supplied safety cable as an added safety measure to prevent accidental damage in the event of a clamp failure. Important: This step is very important to ensure safe rigging of the fixture. TP02-CW,WW User Manual XM1268/1257-V1.0-NR...
Page 10
If you lack these qualifications, do not attempt the rigging of this device yourself. Improper installation/ rigging can result in serious bodily injury. TP02-CW,WW User Manual XM1268/1257-V1.0-NR...
XLR plug with a 120 Ω resistor connected between pins 2 and 3,which is then plugged into the output (female) XLR socket of the last fixture in the chain. Please see illustrations below. TP02-CW,WW User Manual XM1268/1257-V1.0-NR...
Last Run Time XXXX(Hours) Fixture Last times clear LastRun Password Password=XXX Timer Password 038 Clear Last Run ON/OFF Clear Fixture Last time Temperature Info Head Temp XXX℃/℉ Temperature in the head Software Version Software version Vx.x.x… TP02-CW,WW User Manual XM1268/1257-V1.0-NR...
Page 13
With this function you can display the DMX 512 value of each channel. The display automatically shows the channel with a value changing. 1. Access the main menu. 2. Tap the <Up/Down>button until“ ”is displayed. ValuDisp TP02-CW,WW User Manual XM1268/1257-V1.0-NR...
Page 14
With this function, you can clear last run time of the fixture. The display shows “ON” or “OFF”, Press “Enter” to confirm. 1. Access the main menu. 2. Press <Up/Down>, the display will show “Clear Last Run”. 3. At“ ”menu input right password, Press< ENTER>, the display will show TimePass TP02-CW,WW User Manual XM1268/1257-V1.0-NR...
Page 15
3. Press< ENTER>, the display will show“No DMX Status”. 4. The display show “Hold”,Press <Up/Down>, the display will show “CloShut”, “Auto”. 5. Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu. Hibernation: Standby mode TP02-CW,WW User Manual XM1268/1257-V1.0-NR...
Page 16
2.Press <Up/Down>, the display will show “Flip Display”. 3.Press< ENTER>, the display will show “Flip Display”. 4.The display show “OFF”, Press <Up/Down>, the display will show “ON” 5.Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu. TP02-CW,WW User Manual XM1268/1257-V1.0-NR...
Page 17
2.Press <Up/Down>, the display will show“Freq Refresh”. 3.Press< ENTER>, the display will show“Freq Refresh”. 4.The display show“900-1500Hz,2.5K,4K,5K,10K,15K,20K,25K”,Press <Up/Down>, the display will show “ON” ,. 5.Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu. 9.3.7. Set Gamma TP02-CW,WW User Manual XM1268/1257-V1.0-NR...
Page 18
5.Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu. 9.6. Language Set With this function, you can set the device language to English or Chinese, the default is Chinese. 1.Tap <MODE/ESC>button,access the main menu,Tap the <Up/Down>button until TP02-CW,WW User Manual XM1268/1257-V1.0-NR...
DMX channel´s functions and their values : Mode/Channel Value Function Dimmer Intensity: : 0-255 Intensity 0 to 100% Dimmer Fine: 0-255 Intensity 0 to 100% Dim Modes 0-20 Standard 21-40 Stage 41-60 61-80 Architectural 81-100 Theatre 101-255 Default to Unit Setting TP02-CW,WW User Manual XM1268/1257-V1.0-NR...
Please refer to the instructions under “Installation instructions”. Should you need any spare parts, please order genuine parts from your local dealer. 12. SERVICE For all service needs please contact your local authorized dealer or Terbly directly. Our contact details are: Email: QA@terbly.com...