Advertisement
save
6a.
II
config
O )))
BMS
PL
1
2
link?
mode?
test
10% A
20% B
add
4
5
zone
40% D
50% E
7
8
%
A-G
on/off
70% G
power upbackground IR group
0
on
II
delay
pir
daylight RF channel
min
PL
scene
2
A
20% B
5
save
D
50% E
8
G
config
O )))
0
min
link?
mode?
test
add
zone
save
%
A-G
on/off
power upbackground IR group
delay
pir
daylight RF channel
g
O )))
scene
mode?
test
add
zone
10 Philips Lighting Controls
Set light output per group
I /II
mode
Unlock the group, refer to step 5a.
W/C
• Group will be unlocked for further operation.
3
100 h
30% C
6
60% F
9
0
reset
off
I /II
group
W/C
3
Luminaire
Luminaire
30% C
6
II
60% F
BMS
9
1
mode
10% A
off
4
40% D
100 h
group
7
70% G
on
Lock the group, refer to step
• After locking, lighting group is operational at selected light level.
Note that the default setting is Medium. To get to high, go one step up.
0
To get to Minimum, go two steps down.
reset
mode
100 h
config
If unsure about light output selection, step up to the highest setting
and observe the subtle reduction in light level each time you
activate lower settings.
link?
mode?
mode
save
II
0
config
O )))
BMS
1
reset
link?
mode?
test
Luminaire
10% A
add
Luminaire
4
zone
To select light output settings, use the up and down
40% D
arrows to change between high, medium, low and
7
minimum. Light level can be altered one step at a time.
%
A-G
on/off
70% G
The daylight button must be pressed to initiate a new
power upbackground IR group
config
change after every end of step.
on
delay
pir
daylight RF channel
For each step up or down:
scene
Point to any luminaire
II
Luminaire
in the group and
press "daylight."
Luminaire
BMS
1
While the remote is
I /II
blinking, select:
10% A
20% B
PL
W/C
4
or
2
3
40% D
50% E
20% B
config
30% C
Then press "send."
7
5
6
End of step.
70% G
save
50% E
60% F
on
link?
8
9
min
0
off
4e.
min
group
save
on/off
power upbackground IR group
Medium
Will move light output setting from default
to High
of 88% to 100%.
delay
save
Medium
Will move light output setting from default
config
scene
to Low
of 88% to 77%.
Low to
Will move light output setting from default
Minimum
of 77% to 66%.
mode
O )))
link?
mode?
test
100 h
zone
I/II
mode
PL
W/C
2
3
100 h
Luminaire
20% B
30% C
5
6
Luminaire
50% E
60% F
8
9
group
0
reset
0
off
min
group
Red LED on
I /II
remote will
start blinking.
daylight
PL
W/C
2
3
save
Red LED on
remote will
30% C
stop blinking.
5
6
mode
60% F
mode
Depending on the
8
9
O )))
0
sensor firmware
version, lights may or
reset
may not flash twice
0
off
to confirm the light
mode?
test
100 h
level change.
add
group
config
zone
%
A-G
0
reset
pir
daylight RF channel
mode
save
O )))
test
100 h
add
save
II
II
II
BMS
1
10% A
4
40% D
7
70% G
on
config
link?
mode?
P
2
20
5
50
8
0
mi
sa
O
Advertisement
