Page 1
U s e r M a n u a l 020-001438-01 Christie DHD410S...
Page 2
The warranty does not apply to any product where the serial number has been removed or obliterated. The warranty also does not apply to any product sold by a reseller to an end user outside of the country where the reseller is located unless (i) Christie has an office in the country where the end user is located or (ii) the required international warranty fee has been paid.
• Do not open or disassemble the projector as this may cause electric shock. • All installations must be performed by Christie qualified authorized trained installers. • Keep all combustible material away from the concentrated light beam of the projector.
• Follow the control, adjustment, or operation procedures to avoid damage or injury from exposure of laser radiation. • The instructions for the assembly, operation, and maintenance include clear warnings concerning precautions to avoid possible exposure to hazardous laser radiation. DHD410S User Manual 020-001438-01 Rev. 1 (06-2018)
Introduction Main unit Ind. Part name Ind. Part name Control Panel Speaker Focus switch Power Socket Ventilation (inlet) Input/Output Connections IR Receiver Lens Ventilation (outlet) DHD410S User Manual 020-001438-01 Rev. 1 (06-2018)
Audio Input Connector (microphone) Interactive Connector (3.5 mm mini jack) KensingtonTM Lock Port VGA-Out/VGA2-In Connector Monitor loop through only support in VGA1-In/YPbPr. Control panel Using the control panel Power Powering the projector on/off on page 14. DHD410S User Manual 020-001438-01 Rev. 1 (06-2018)
Page 10
Press INPUT to select an input signal. Four Directional Select Keys Use to select items or make adjustments to your selection. ON/Standby LED Refer to the LED indicator of the projector power status. IR Receiver — DHD410S User Manual 020-001438-01 Rev. 1 (06-2018)
Use Up, Down, Left, Right arrows to select items or make adjustments to your Menu Press Menu to launch the on-screen display (OSD) menu. T o exit OSD, press Menu again. Exit Press Exit to close the OSD menu. DHD410S User Manual 020-001438-01 Rev. 1 (06-2018)
Page 12
Press VGA2 to choose VGA IN 2 connector . HDMI2 Press HDMI2 to choose HDMI IN 2 connector. Video Press Video to choose Composite video source. Screen freeze Pause the screen image. Press again to resume the screen image. DHD410S User Manual 020-001438-01 Rev. 1 (06-2018)
Ind. Connector name Ind. Connector name RS232 Cable Power Cord VGA Cable VGA Output Cable HDMI Cable DC to DC Cable USB Cable Audio Output Cable Audio Cable/RCA Audio Input Cable RJ45 Cable DHD410S User Manual 020-001438-01 Rev. 1 (06-2018)
Powering on the projector 1. Securely connect the power cord and signal cable. When connected, the POWER/STANDBY LED turns orange. 2. Turn on the projector by pressing button either on the projector or on the remote. DHD410S User Manual 020-001438-01 Rev. 1 (06-2018)
If you want to turn the projector back on, you must wait until the projector has completed the cooling cycle and has entered standby mode. Once in standby mode, press button to restart the projector. DHD410S User Manual 020-001438-01 Rev. 1 (06-2018)
2. Rotate the adjustable ring clockwise to raise the projector or counter clockwise to lower it. 3. Repeat with the remaining feet as needed. Tilt-Adjustment Feet Tilt-Adjustment Ring Adjusting the projector’s focus o focus the image, slide the focus switch to left/right until the image is clear. DHD410S User Manual 020-001438-01 Rev. 1 (06-2018)
Page 17
Installation 1080p series: The projector will focus at distances from 1.443 to 1.887 feet (0.437 to 0.572 meters). Focus switch DHD410S User Manual 020-001438-01 Rev. 1 (06-2018)
5. Press Enter to confirm, and the screen will return to the main menu. 6. To exit, press Menu again. The OSD menu will close and the projector will automatically save the new settings. DHD410S User Manual 020-001438-01 Rev. 1 (06-2018)
Adjust the color balance of red and green. • Press the Left arrow to increase the amount of green in the image. • Press the Right arrow to increase the amount of red in the image. DHD410S User Manual 020-001438-01 Rev. 1 (06-2018)
Page 21
User Controls Option Description Gamma This allows you to adjust the gamma value to obtain the better image contrast for the input. Note: Sharpness, Saturation and Hue functions are only supported under video mode. DHD410S User Manual 020-001438-01 Rev. 1 (06-2018)
• Rear: When selected, the image will appear reversed. • Rear Ceiling: When selected, the image will appear reversed in upside down position. Note: H. Position and V. Position ranges will depend on input source. DHD410S User Manual 020-001438-01 Rev. 1 (06-2018)
• Output: Choose Output to enable the VGA Out function once the projector is powered on. Test Pattern Display a test pattern. Factory Reset Choose Yes to return the parameters on all menus to the factory default settings. Language DHD410S User Manual 020-001438-01 Rev. 1 (06-2018)
• Press the Left arrow to decrease the volume. • Press the Right arrow to increase the volume. Microphone Volume • Press the Left arrow to decrease the microphone volume. • Press the Right arrow to increase the microphone volume. DHD410S User Manual 020-001438-01 Rev. 1 (06-2018)
Cleaning Up Reminder: Select Yes to reset the dust filter hour counter after replacing or cleaning the dust filter . Information Display the projector information for model name, SNID, source, resolution, software version, and aspect ratio on the screen. DHD410S User Manual 020-001438-01 Rev. 1 (06-2018)
Display the projection time of ECO mode. Laser Power Mode • Normal: Normal mode. • ECO: Use this function to dim the projector light which will lower power consumption and extend the light source life. DHD410S User Manual 020-001438-01 Rev. 1 (06-2018)
Page 27
• Frame Sequential is supported the DLP Link 3D input signals from VGA/HDMI connector. • Frame Sequential/Field Sequential are supported the HQFS 3D input signals from Video connector. • Frame Packing/Side by Side (Half)/Top and Bottom are supported from HDMI 1.4a 3D input signals DHD410S User Manual 020-001438-01 Rev. 1 (06-2018)
You must to unplug the Mini USB cable that connects NB/desktop with the projector before using the Interactive function. After you complete the Interactive Settings in OSD, use Mini USB cable to connect NB/desktop with the projector . DHD410S User Manual 020-001438-01 Rev. 1 (06-2018)
Display the group name. Projector Name Display the projector name. Location Display the projector location. Contact Display the contact information. To set a manual IP address while DHCP off, use the WEB Management interface. DHD410S User Manual 020-001438-01 Rev. 1 (06-2018)
Based on network web-page for the input-string in [tools] tab, the limitation for Input-Length is in the below list (space and the other punctuation key included): Category Item Input-length (characters) Crestron Control IP Address IP ID Port Projector Projector Name Location Assigned To DHD410S User Manual 020-001438-01 Rev. 1 (06-2018)
8. In the Proxy Server area, cancel the Use a proxy server for your LAN checkbox, then click OK button twice. 9. Open Internet Explorer and type the IP address 10.0.21.200 in the address box. 10. Press Enter. DHD410S User Manual 020-001438-01 Rev. 1 (06-2018)
(Operation UI as following image) Crestron RoomView’s function is set according to the products’ models and specifications. For further information, please visit: http://www.crestron.com & www.crestron.com/getroomview DHD410S User Manual 020-001438-01 Rev. 1 (06-2018)
3. When the Input menu appears, press the up and down arrow keys to select Multimedia and the Enter key to confirm. Mobile display To access the media files stored on your mobile device or tablet PC, do the following: 1. On Multimedia menu, select Mobile/Tablet. DHD410S User Manual 020-001438-01 Rev. 1 (06-2018)
4. Launch EZview application and type the control code shown on the right-bottom side of the screen. 5. Wait until the connection is established. The media files on your desktop can be accessed using the projector. DHD410S User Manual 020-001438-01 Rev. 1 (06-2018)
Music—Select this option to set the repeat mode. • WiFi—Select this option to configure the Wi-Fi connection. 3. Use the Up and Down arrows to select the adjust/select the setting and press the Enter key to confirm. DHD410S User Manual 020-001438-01 Rev. 1 (06-2018)
2. Pull out the dust filter, as shown in the illustration (1). 3. Carefully remove the dust filter. Then clean or change the filter in illustration (2). 4. To install the filter, reverse the previous steps. DHD410S User Manual 020-001438-01 Rev. 1 (06-2018)
Page 37
Appendices 5. Turn on the projector and reset the filter usage counter after the dust filter is replaced. DHD410S User Manual 020-001438-01 Rev. 1 (06-2018)
Stop bits Flow control None RS232 signals connection RS232 shell is grounded. Commands set list Command description Command Projector return N value Note Power (PWR n) Pass: P 0: Off Fail: F 1: On DHD410S User Manual 020-001438-01 Rev. 1 (06-2018)
Page 43
1: Auto Fail: F 2: 4:3 3: 16:9 4: 16:10 Digital Zoom (DZM n) Pass: P 0: Zoom- Fail: F 1: Zoom+ Keystone (KST n) Pass: P Value: -40 ~ 40 Fail: F DHD410S User Manual 020-001438-01 Rev. 1 (06-2018)
Page 44
Value: 0~30 Microphone Volume Fail: F Auto Power Off (min) (ASH n) Pass: P Step = 5 (0,5,10,15,20… Fail: F 95,100,105,110,115, 120) High Altitude (HAT n) Pass: P 0: Off Fail: F 1: On DHD410S User Manual 020-001438-01 Rev. 1 (06-2018)
• Wall Mount - Silver + white (140-120115-XX) • IR Pen (140-121105-XX) • Dust Filter (003-005584-XX) • Captiva Touch (140-122106-XX) Regulation and safety notices This appendix lists the general notices of your projector. DHD410S User Manual 020-001438-01 Rev. 1 (06-2018)
Remarque à l’intention des utilisateurs canadiens Cet appareil numerique de la classe A est conforme a la norme NMB-003 du Canada. Declaration of Conformity for EU countries • EMC Directive 2004/108/EC (including amendments) DHD410S User Manual 020-001438-01 Rev. 1 (06-2018)
1. To prevent damage to your projector, please use wall mount (140-120104-XX/ 140-120115-XX). 2. If you want to use a third-party wall mount kit, ensure the screws used to attach a mount to the projector meet the following specifications: • Screw type: M4*4 DHD410S User Manual 020-001438-01 Rev. 1 (06-2018)
Page 48
Appendices • Minimum screw length: 10 mm DHD410S User Manual 020-001438-01 Rev. 1 (06-2018)
Page 49
Corporate of ces Worldwide of ces Christie Digital Systems USA, Inc. Australia Germany Republic of South Africa United Kingdom Cypress ph: +61 (0) 7 3624 4888 ph: +49 2161 664540 ph: +27 (0)11 510 0094 ph: +44 (0) 118 977 8000...