WAGNER PROTEC GM 1-530 Translation Of The Original Operating Manual page 29

VERSION 07/2017
OPERATING MANUAL
12 ACCESSORIES
Nozzle holder / anti-contact guard: see Chapter
12.1 NOZZLE FOR NOZZLE HOLDER PT-HD GM1
Nozzle table
In order to determine the order number of a nozzle, please select the number
Order No.
from the table and replace the three xxx.
1006 x x x
Example: This means nozzle 411 has order number: 1006411
Size
10° 20° 30°
07 ***
09 *** 209 309 409 509 609
11 111 211 311 411 511 611
13 113 213 313 413 513 613
15 115 215 315 415 515 615 715 815
17 217 317 417 517 617 717
19 219 319 419 519 619 719 819
21 221
23 223
25 225
27 227
29
31 231
35 235
43 243
52
51 104 152 203 254 305 356 406
(2.0) (4.0) (6.0)
Spray jet width in mm (inch) **
Nozzle table
In order to determine the order number of a nozzle, please select the number
Order No.
from the table and replace the three xxx.
556 x x x
Example: This means nozzle 417 has order number: 556417
Size
10° 20° 30°
13 113 213 313 413
15 115 215 315 415 515
17 117 217 317 417 517 617
19 119 219 319 419 519 619
21 221 321 421 521 621
23 223 323 423 523
25 225 325 425 525
31
33
35
51
55
61
65
51 104 152 203 254 305 356 406
(2.0) (4.0) (6.0)
Spray jet width in mm (inch) **
ORDER NUMBER DOC 2349369
WAGNER Profi Tip HD
Spray angle
40° 50° 60° 70°
407
421 521 621
423 523 623 723 823
425 525 625
427 527 627
629
431 531 631
435 535 635
543
552
(8.0) (10.0) (12.0) (14.0) (16.0)
Spray angle
40° 50° 60° 70°
531
535
(8.0) (10.0) (12.0) (14.0) (16.0)
13.2
Product filter
80° (in mesh)
813
821
825
827
* Tested with water and 100 bar pressure.
** ** Spray jet width at approx. 30 cm distance from the sprayed
object and 110 bar (11 MPa) of pressure with lacquer 56 DIN/4
seconds
*** Possible deviations in the spray jet width
PROTEC tip
Product filter
80° (in mesh)
200
815
817
* Tested with water and 100 bar pressure.
** ** Spray jet width at approx. 30 cm distance from the sprayed
object and 110 bar (11 MPa) of pressure with lacquer 56 DIN/4
seconds
Drilled hole Product flow *
inch mm l/min
0.007 0.18 0.21
0.009 0.23 0.23
0.011 0.28 0.34
0.013 0.33 0.50
0.015 0.38 0.68
0.017 0.43 0.88
0.019 0.48 1.09
0.021 0.53 1.31
0.023 0.58 1.63
0.025 0.64 1.92
0.027 0.69 2.25
0.029 0.75 2.58
0.031 0.79 2.95
0.035 0.89 3.80
0.043 1.10 5.00
0.052 1.30 6.14
Drilled hole Product flow *
inch mm l/min
0.013 0.33 0.50
0.015 0.38 0.70
0.017 0.43 0.85
0.019 0.48 1.00
0.021 0.53 1.20
0.023 0.58 1.40
0.025 0.64 1.60
0.031 0.79 2.25
0.033 0.84 2.50
0.035 0.89 2.80
0.051 1.30 5.20
0.055 1.40 6.00
0.061 1.55 7.50
0.065 1.65 9.00
gal/min
0.055
0.061
0.090
0.132
0.180
0.232
0.288
0.346
0.431
0.507
0.594
0.682
0.779
1.004
1.321
1.622
gal/min
0.15
0.19
0.22
0.26
0.32
0.37
0.42
0.60
0.66
0.74
1.38
1.59
1.98
2.38
29