Fujitsu Siemens Computers SPARC Enterprise T5140 Installation Manual
  1. Manuals
  2. Brands
  3. Fujitsu Siemens Computers Manuals
  4. Server
  5. SPARC Enterprise T5140
  6. Installation manual
Fujitsu Siemens Computers SPARC Enterprise T5140 Installation Manual

Fujitsu Siemens Computers SPARC Enterprise T5140 Installation Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Installation Guide
English
SPARC® Enterprise T5140 / T5240 Servers

Advertisement

Table of Contents
loading

Related Manuals for Fujitsu Siemens Computers SPARC Enterprise T5140

Summary of Contents for Fujitsu Siemens Computers SPARC Enterprise T5140

  • Page 1 Installation Guide English SPARC® Enterprise T5140 / T5240 Servers...
  • Page 3 SPARC Enterprise ® T5140 and T5240 Servers Installation Guide Order No. U41767-J-Z816-1-76 Part No. 875-4310-10 February 2008, Revision A...
  • Page 4 Copyright 2008 Sun Microsystems, Inc., 4150 Network Circle, Santa Clara, California 95054, U.S.A. All rights reserved. FUJITSU LIMITED provided technical input and review on portions of this material. Sun Microsystems, Inc. and Fujitsu Limited each own or control intellectual property rights relating to products and technology described in this document, and such products, technology and this document are protected by copyright laws, patents and other intellectual property laws and international treaties.
  • Page 5 Copyright 2008 Sun Microsystems, Inc., 4150 Network Circle, Santa Clara, California 95054, Etats-Unis. Tous droits réservés. Entrée et revue tecnical fournies par FUJITSU LIMITED sur des parties de ce matériel. Sun Microsystems, Inc. et Fujitsu Limited détiennent et contrôlent toutes deux des droits de propriété intellectuelle relatifs aux produits et technologies décrits dans ce document.

  • Page 7: Table Of Contents

    Slide Rail Assembly Notes for Both Servers 10 Cable Management Notes for Both Servers 13 Safety Precautions 14 Installing the SPARC Enterprise T5140 and T5240 Servers 15 Installing the Servers in a Rack 15 ▼ To Install the Slide Rail Assemblies 16 ▼...
  • Page 8 Booting the Solaris Operating System 56 ▼ To Boot the Solaris Operating System 56 ▼ To Avoid Booting the Solaris Operating System at Start Up 57 ▼ To Reset the System 57 SPARC Enterprise T5140 and T5240 Servers Installation Guide • February 2008...
  • Page 9 ▼ To Power Cycle the System 57 Verifying System Functionality 59 Updating the Firmware 61 The flashupdate command 61 Updating the Firmware 61 ▼ To Update the Firmware 62 Selecting a Boot Device 65 Selecting a Boot Device 65 ▼ To Select a Boot Device 66 Installing the Servers With the Express Rail Rackmounting Kit 67 Slide Rail Assembly Notes for the Express Rail Rackmounting Kit 68...
  • Page 10 SPARC Enterprise T5140 and T5240 Servers Installation Guide • February 2008...
  • Page 11 SPARC Enterprise T5140 Server 2 FIGURE 1-2 SPARC Enterprise T5240 Server 2 FIGURE 1-3 Rear Panel Cable Connectors and LEDs on the SPARC Enterprise T5140 Server 8 FIGURE 1-4 Front Panel USB Ports on the SPARC Enterprise T5140 Server 8 FIGURE 1-5...
  • Page 12 Attaching Express Slide Rails to the Rack 76 FIGURE C-8 Inserting Express Rail Mounting Brackets Into the Slide Rails 77 FIGURE C-9 Sliding the Express Rail Release Tab and Securing the Server in the Rack 78 SPARC Enterprise T5140 and T5240 Servers Installation Guide • February 2008...
  • Page 13 Tables TABLE 1-1 Ethernet Connection Transfer Rates 7 TABLE 3-1 Disk Slot Numbers, Logical Device Names, and Physical Device Names 55 TABLE 3-2 Device Identifiers and Devices 55...
  • Page 14 SPARC Enterprise T5140 and T5240 Servers Installation Guide • February 2008...

  • Page 15: Preface

    Use the product according to the instructions and information available in this manual. Keep this manual handy for further reference. Fujitsu Siemens Computers makes every effort to prevent users and bystanders from being injured or from suffering damage to their property. Use the product according to this manual.
  • Page 16 Appendix B provides instructions for selecting a boot device. Appendix C provides instructions for installing the servers into a rack with the express rail rackmounting kit. xiv SPARC Enterprise T5140 and T5240 Servers Installation Guide • February 2008...
  • Page 17 The latest versions of all the SPARC Enterprise Series manuals are available at the following Web sites: http://manuals.fujitsu-siemens.com/ Title Description Order No. SPARC Enterprise T5140 and T5240 Information about the latest product U41765-J-Z816-x-76 Servers Product Notes updates and issues SPARC Enterprise T5140 and T5240...
  • Page 18 You must be superuser to do variables with real names or this. values. To delete a file, type filename. * The settings on your browser might differ from these settings. xvi SPARC Enterprise T5140 and T5240 Servers Installation Guide • February 2008...
  • Page 19 Prompt Notations The following prompt notations are used in this manual. Shell Prompt C shell machine-name% C shell superuser machine-name# Bourne shell and Korn shell Bourne shell and Korn shell superuser ILOM service processor -> ALOM compatibility shell sc> ™ OpenBoot PROM firmware Conventions for Alert Messages...
  • Page 20 Unpacking optional adapters and such packages delivered to the users ■ Also, important alert messages are shown in “Important Alert Messages” on page xix. xviii SPARC Enterprise T5140 and T5240 Servers Installation Guide • February 2008...
  • Page 21 Notes on Safety Important Alert Messages This manual provides the following important alert signals: Caution – This indicates a hazardous situation could result in minor or moderate personal injury if the user does not perform the procedure correctly. This signal also indicates that damage to the product or other property may occur if the user does not perform the procedure correctly.
  • Page 22 Task Warning Installation Electric shock There is a potential for electric shock if the server and related equipment are not properly grounded. xx SPARC Enterprise T5140 and T5240 Servers Installation Guide • February 2008...
  • Page 23 ■ Caution – The following tasks regarding this product and the optional products provided from Fujitsu Siemens Computers should only be performed by a certified service engineer. Users must not perform these tasks. Incorrect operation of these tasks may cause malfunction.
  • Page 24 Example: SPARC Enterprise T5240 Server Fujitsu Siemens Computers Welcomes Your Comments We would appreciate your comments and suggestions to improve this document. You can submit your comments by using "Reader's Comment Form." xxii SPARC Enterprise T5140 and T5240 Servers Installation Guide • February 2008...
  • Page 25 Reader's Comment Form ■ Preface xxiii...
  • Page 26 POSTAGE WILL BE PAID BY ADDRESSEE FUJITSU COMPUTER SYSTEMS AT TENTION ENGINEERING OPS M/S 249 1250 EAST ARQUES AVENUE P O BOX 3470 SUNNYVALE CA 94088-3470 FOLD AND TAPE xxiv SPARC Enterprise T5140 and T5240 Servers Installation Guide • February 2008...
  • Page 27 “Cable Management Notes for Both Servers” on page 13 ■ “Safety Precautions” on page 14 ■ The SPARC Enterprise T5140 server is a 1 rack unit (1U) server ( ). The FIGURE 1-1 SPARC Enterprise T5240 server is a 2 rack unit (2U) server (...

  • Page 28: Figure 1-1 Sparc Enterprise T5140 Server

    SPARC Enterprise T5140 Server FIGURE 1-1 SPARC Enterprise T5240 Server FIGURE 1-2 SPARC Enterprise T5140 and T5240 Servers Installation Guide • February 2008...

  • Page 29: Preparing For Installation

    Tools and Equipment Needed To install the system, you must have the following tools: No. 2 Phillips screwdriver ■ ESD mat and grounding strap ■ In addition, you must provide a system console device, such as one of the following: ASCII terminal ■...

  • Page 30: Installation Overview

    5. Connect the server to a serial terminal or a terminal emulator (PC or workstation) to display system messages. See “Powering On the System for the First Time” on page SPARC Enterprise T5140 and T5240 Servers Installation Guide • February 2008...
  • Page 31 Diagnostic test failures will be printed on the serial terminal. For more information, refer to the Integrated Lights Out Manager 2.0 Supplement for SPARC Enterprise T5140 and T5240 Servers. 6. Connect the data cables to the server, but do not connect the AC power cable yet.

  • Page 32: Cabling Notes For Both Servers

    Refer to the SPARC Enterprise T5140 and T5240 Servers Product Notes for a list of required patches. 14. Load additional software from the Solaris media kit (optional). The Solaris media kit (sold separately) includes several CDs containing software to help you operate, configure, and administer your server. Refer to the documentation provided with the media kit for a complete listing of included software and detailed installation instructions.

  • Page 33: Port, Connector, And Led Locations For Both Servers

    Ethernet ports are labeled NET0, NET1, NET2, and NET3. The Ethernet interfaces ■ operate at 10 Mbps, 100 Mbps, and 1000 Mbps. shows the transfer rates TABLE 1-1 for the Ethernet ports. Ethernet Connection Transfer Rates TABLE 1-1 Connection Type IEEE Terminology Transfer Rate Ethernet...

  • Page 34: Figure 1-3 Rear Panel Cable Connectors And Leds On The Sparc Enterprise T5140 Server

    Rear Panel Cable Connectors and LEDs on the SPARC Enterprise T5140 Server FIGURE 1-3 Figure Legend Power supply 0 Gbit Enet port NET2 Power supply 1 Gbit Enet port NET3 Locator LED button USB port 0 Service Required LED USB port 1...

  • Page 35: Figure 1-5 Rear Panel Cable Connectors And Leds On The Sparc Enterprise T5240 Server

    for the locations of the ports on the SPARC Enterprise FIGURE 1-5 FIGURE 1-6 T5240 server. Rear Panel Cable Connectors and LEDs on the SPARC Enterprise T5240 Server FIGURE 1-5 Figure Legend Power supply 0 Gbit Enet port NET3 Power supply 1 USB port 0 Locator LED button USB port 1...

  • Page 36: Slide Rail Assembly Notes For Both Servers

    Note – The slide rail assemblies are different for the T5140 and T5240 servers. The removable mounting bracket of the SPARC Enterprise T5140 rails slides 13 in. (33 cm) out of the slide rail, then locks in place. The removable mounting bracket of the SPARC Enterprise T5240 rails slide 14 in.

  • Page 37: Figure 1-7 Sections Of The Slide Rail Assembly On The Sparc Enterprise T5240 Server

    Sections of the Slide Rail Assembly on the SPARC Enterprise T5240 Server FIGURE 1-7 Figure Legend Mounting bracket Middle section Front section Rear section The front, middle, and rear sections form the slide rail. The middle and rear sections ■ have holes for mounting screws, and adjust to fit rack depths from 24 in.

  • Page 38: Figure 1-8 Locating The Locks On The Slide Rail Assembly For The Sparc Enterprise T5240 Server

    Locating the Locks on the Slide Rail Assembly for the SPARC Enterprise FIGURE 1-8 T5240 Server SPARC Enterprise T5140 and T5240 Servers Installation Guide • February 2008...

  • Page 39: Cable Management Notes For Both Servers

    Cable Management Notes for Both Servers The same cable management arm (CMA) is included with the rackmounting kit for each server ( ). The CMA clips onto the slide rails. Use the velcro straps to FIGURE 1-9 secure cabling to the CMA. Cable Management Arm for Both Servers FIGURE 1-9 Chapter 1 Preparing for Installation...

  • Page 40: Safety Precautions

    Two people are required to lift and mount this 2U server into a rack enclosure when using the procedures in this document. Caution – When completing a two-person procedure, always communicate your intentions clearly before, during, and after each step to minimize confusion. SPARC Enterprise T5140 and T5240 Servers Installation Guide • February 2008...

  • Page 41: Installing The Sparc Enterprise T5140 And T5240 Servers

    C H A P T E R Installing the SPARC Enterprise T5140 and T5240 Servers This chapter provides instructions for installing the servers into an equipment rack. Note – If your rackmount kit came with its own instructions, use the instructions in your rackmount kit instead of the instructions in this chapter.

  • Page 42: To Install The Slide Rail Assemblies

    Simultaneously press and hold the upper and lower lock buttons of the slide rail lock ( FIGURE 2-1 Unlocking the Slide Rail Assembly (Either Server) FIGURE 2-1 b. Pull the mounting bracket out until it locks in the extended position. SPARC Enterprise T5140 and T5240 Servers Installation Guide • February 2008...

  • Page 43: Figure 2-2 Location Of The Mounting Bracket Release Button (Either Server)

    FIGURE 2-2 d. Press the metal lever (labeled Push) on the middle section ( ) of FIGURE 2-3 the sliding rail, then push the middle section back into the rack. Chapter 2 Installing the SPARC Enterprise T5140 and T5240 Servers...

  • Page 44: Figure 2-3 Unlocking The Slide Rail Middle Section (Either Server)

    SPARC Enterprise T5140 and T5240 Servers Installation Guide • February 2008...

  • Page 45: Figure 2-4 Attaching A Mounting Bracket To The Chassis (Either Server)

    If your rack has threaded mounting holes in the rack posts, determine ■ whether the threads are metric or standard. Select the appropriate screws from the package included in the mounting kit. Chapter 2 Installing the SPARC Enterprise T5140 and T5240 Servers...

  • Page 46: Figure 2-5 Mounting A Slide Rail (Either Server)

    Loosely attach the rear of the slide rail to the rear rack post with two screws. 7. Attach the second slide rail to the left rack posts in a similar manner. Do not tighten the screws. SPARC Enterprise T5140 and T5240 Servers Installation Guide • February 2008...

  • Page 47: Figure 2-6 Using The Slide Rail Spacing Tool To Adjust The Distance Between The Slide Rails (Either Server)

    Tighten the screws to lock the ends of the rails in place. e. At the rear of the rack, repeat Step a through Step d. for the rear ends of the rails. Chapter 2 Installing the SPARC Enterprise T5140 and T5240 Servers...

  • Page 48: To Insert And Lock The Server In The Rack

    2. Insert the ends of the mounting brackets into the sliding rails ( FIGURE 2-7 Mounting the Chassis on the Slide Rails (Either Server) FIGURE 2-7 SPARC Enterprise T5140 and T5240 Servers Installation Guide • February 2008...

  • Page 49: Installing The Cable Management Arm For Both Servers

    At the rear of the rack, plug the CMA rail extension into the end of the left sliding rail assembly. The tab at the front of the rail extension clicks into place. Chapter 2 Installing the SPARC Enterprise T5140 and T5240 Servers...

  • Page 50: Figure 2-8 Inserting The Cma Rail Extension Into The Rear Of The Left Slide Rail (Either Server)

    Connector for Inner Member. This extension attaches to the right mounting bracket. The larger extension is called the CMA Connector for Outer Member, and attaches to the right sliding rail. SPARC Enterprise T5140 and T5240 Servers Installation Guide • February 2008...

  • Page 51: Figure 2-9 Mounting The Inner Cma Connector (Either Server)

    Slide the smaller extension into the square hole on the middle-in-width of the clip that is located at the end of the mounting bracket. Mounting the Inner CMA Connector (Either Server) FIGURE 2-9 Chapter 2 Installing the SPARC Enterprise T5140 and T5240 Servers...

  • Page 52: Figure 2-10 Attaching The Outer Cma Connector (Either Server)

    4. Insert the larger extension into the end of the right sliding rail ( FIGURE 2-10 Attaching the Outer CMA Connector (Either Server) FIGURE 2-10 SPARC Enterprise T5140 and T5240 Servers Installation Guide • February 2008...

  • Page 53: Figure 2-11 Mounting The Left Side Of The Slide Rail (Either Server)

    CMA rail extension ( FIGURE 2-11 The plastic tab on the CMA rail extension locks the hinged plastic connector in place. Mounting the Left Side of the Slide Rail (Either Server) FIGURE 2-11 Chapter 2 Installing the SPARC Enterprise T5140 and T5240 Servers...

  • Page 54: To Verify The Operation Of The Slide Rails And The Cma

    5. Verify that the CMA extends fully and does not bind in the slide rails. 6. Verify that the server extends fully and locks in the maintenance position. The server should stop after approximately 15 inches (40 cm) of travel. SPARC Enterprise T5140 and T5240 Servers Installation Guide • February 2008...

  • Page 55: Figure 2-13 Rail Mounting Bracket Release Button (Either Server)

    FIGURE 2-13 8. Verify that the CMA retracted without binding. 9. Adjust the cable straps and CMA as required to secure the cables. “Managing Cables With the CMA” on page Chapter 2 Installing the SPARC Enterprise T5140 and T5240 Servers...

  • Page 56: Connecting The Server Cables For Both Servers

    Note – The cable and DB-9 RJ-45 adapters are for the host serial port, and not for the server SER MGT port. Service Processor Serial Management Port – Rear Panel FIGURE 2-14 SPARC Enterprise T5140 and T5240 Servers Installation Guide • February 2008...

  • Page 57: To Connect The Service Processor Network Management Port

    Note – If you have access to a DHCP server on the network, you can see the service processor get an IP address because the DHCP client is enabled by default. Chapter 2 Installing the SPARC Enterprise T5140 and T5240 Servers...

  • Page 58: To Connect The Ethernet Network Cables

    For example, if you have not prepared a display before connecting the AC power cable, system messages might be lost. Caution – Finish the hardware procedures in this chapter, but do not attach the AC power cable yet. SPARC Enterprise T5140 and T5240 Servers Installation Guide • February 2008...

  • Page 59: Managing Cables With The Cma

    CMA securing the cables inside the CMA. ( FIGURE 2-17 Securing the Server Cables With the CMA and Velcro Straps (Either Server) FIGURE 2-17 Chapter 2 Installing the SPARC Enterprise T5140 and T5240 Servers...

  • Page 60: Dismounting The Servers

    Dismounting the Servers To install or replace internal parts in the server, you must first remove the server from the rack. For the removal procedure, refer to the SPARC Enterprise T5140 and T5240 Servers Service Manual. SPARC Enterprise T5140 and T5240 Servers Installation Guide • February 2008...
  • Page 61 Chapter 2 Installing the SPARC Enterprise T5140 and T5240 Servers...
  • Page 62 SPARC Enterprise T5140 and T5240 Servers Installation Guide • February 2008...

  • Page 63: Powering On The System

    C H A P T E R Powering On the System This chapter includes instructions for booting the servers and for enabling the service processor network management port. This chapter contains the following topics: “Powering On the System for the First Time” on page 37 ■...

  • Page 64: Ilom Service Processor

    Time” on page For a more detailed discussion on configuring the system console and connecting terminals, refer to the SPARC Enterprise T5140 and T5240 Servers Administration Guide. ILOM Service Processor After the system console finishes its low-level system diagnostics, the ILOM service processor initializes and runs a higher level of diagnostics.
  • Page 65 No handshake ■ A null modem configuration is needed, meaning the transmit and receive signals are reversed (crossed over) for DTE to DTE communications. You can use the supplied RJ-45 crossover adapters with a standard RJ-45 cable to achieve the null modem configuration.

  • Page 66: Figure 3-1 Server Connections

    5. Connect an Ethernet cable between one of the server’s NET ports ( FIGURE 3-1 and the network to which the server will communicate. 6. Plug the power cords into the power supplies and into a power source. SPARC Enterprise T5140 and T5240 Servers Installation Guide • February 2008...
  • Page 67 Note – Only one power connection is required for operation. Use two power connections for redundancy. The service processor runs on the 3.3V standby voltage. As soon as AC power is connected to the system, the service processor powers on, runs diagnostics, and initializes the ILOM firmware.
  • Page 68 Use the NFSv4 domain derived by the system. Time Zone (Continent) Select your continent. Time Zone (Country or Select your country or region. Region) SPARC Enterprise T5140 and T5240 Servers Installation Guide • February 2008...
  • Page 69 Time Zone Select the time zone. Date and Time Accept the default date and time or change the values. root Password Enter the root password twice. This password is for the superuser account for the Solaris OS on this server. This password is not the SP password. 10.

  • Page 70: Enabling The Service Processor Network Management Port

    1. After the service processor boots, access the ILOM CLI through the serial management port. See “To Log Into the Service Processor Using the Serial Management Port” on page SPARC Enterprise T5140 and T5240 Servers Installation Guide • February 2008...

  • Page 71: Logging Into The Service Processor

    2. Configure the service processor. See “To Configure the Service Processor Network Management Port” on page 3. Commit the changes to the service processor parameters. See Step 5 “To Configure the Service Processor Network Management Port” on page You can now use the network management port at any time to access the service processor.
  • Page 72 Password: password (nothing displayed) Waiting for daemons to initialize... Daemons ready Integrated Lights Out Manager Version 2.0.0.0 Copyright 2007 Sun Microsystems, Inc. All rights reserved. Use is subject to license terms. -> SPARC Enterprise T5140 and T5240 Servers Installation Guide • February 2008...

  • Page 73: To Configure The Service Processor Network Management Port

    Note – For more information on configuring ILOM, refer to the Integrated Lights Out Manager 2.0 Supplement for SPARC Enterprise T5140 and T5240 Servers. Set these network parameters according to the specific details of your network configuration: /SP/network state –...
  • Page 74 CODE EXAMPLE 3-1 processor from a dhcp configuration to a static configuration show /SP/network Command Output CODE EXAMPLE 3-1 -> show /SP/network /SP/network Targets: SPARC Enterprise T5140 and T5240 Servers Installation Guide • February 2008...
  • Page 75 show /SP/network Command Output CODE EXAMPLE 3-1 Properties: commitpending = (Cannot show property) dhcp_server_ip = xxx.xxx.xxx.xxx ipaddress = xxx.xxx.xxx.xxx ipdiscovery = dhcp ipgateway = xxx.xxx.xxx.xxx ipnetmask = 255.255.252.0 macaddress = 00:14:4F:3F:8C:AF pendingipaddress = xxx.xxx.xxx.xxx pendingipdiscovery = static pendingipgateway = xxx.xxx.xxx.xxx pendingipnetmask = 255.255.255.0 state = enabled Commands:...

  • Page 76: To Log Into The Service Processor Using The Network Management Port

    Using the Service Processor for Common Operations Note – For more information on using the ILOM service processor, refer to the Integrated Lights Out Manager 2.0 Supplement for SPARC Enterprise T5140 and T5240 Servers. SPARC Enterprise T5140 and T5240 Servers Installation Guide • February 2008...

  • Page 77: To Power On The System

    To Power On the System ▼ 1. Perform the following steps to verify that there are no faults: a. Set the virtual keyswitch to diag mode so that POST will run in Service mode. -> set /SYS keyswitch_state=diag Set ’keyswitch_state’ to ’diag’ b.
  • Page 78 Note – Depending on the configuration of ILOM, POST variables, and whether POST detected faults or not, the server might boot, or the system might remain at the ok prompt. If the system is at the ok prompt, type boot. SPARC Enterprise T5140 and T5240 Servers Installation Guide • February 2008...

  • Page 79: To Connect To The System Console

    4. Use the set /SYS keyswitch_state=normal command to return the virtual keyswitch to Normal mode (default) so that the system can power on and start the boot process. -> set /SYS keyswitch_state=normal Set ’keyswitch_state’ to ’normal’ To Connect to the System Console ▼...

  • Page 80: Devices In The Openboot Device Tree

    Solaris OS. Note – System behavior depends on how the auto-boot variable is set. See the SPARC Enterprise T5140 and T5240 Servers Service Manual for more information. The following example output is a small section of the complete output.

  • Page 81: Booting The Solaris Operating System

    Disk Slot Numbers, Logical Device Names, and Physical Device Names (Continued) TABLE 3-1 Disk Slot Number Logical Device Name Physical Device Name Slot 1 c0t1d0 /devices/pci@0/pci@0/pci@2/scsi@0/sd@1,0 Slot 2 c0t2d0 /devices/pci@0/pci@0/pci@2/scsi@0/sd@2,0 Slot 3 c0t3d0 /devices/pci@0/pci@0/pci@2/scsi@0/sd@3,0 * The logical device names might appear differently on your system, depending on the number and type of add-on disk controllers installed.

  • Page 82: To Boot The Solaris Operating System

    In hard drive HDD0, the Solaris OS is preinstalled. ● If you do not want to start the preinstalled OS, set the Open Boot PROM parameter auto-boot? to false. For example: -> set /HOST/bootmode script="setenv auto-boot? false" SPARC Enterprise T5140 and T5240 Servers Installation Guide • February 2008...

  • Page 83: To Reset The System

    To Reset the System ▼ ● If it is necessary to reset the system, use the shutdown -g0 -i6 -y command. # shutdown -g0 -i6 -y It is not necessary to power the system off and on to simply reset the system. To Power Cycle the System ▼...

  • Page 84: Verifying System Functionality

    Suite (SunVTS™) software to verify the functionality and performance of any installed components, as well as its network connections. Refer to the SunVTS documentation at for more information. http://www.sun.com/documentation SPARC Enterprise T5140 and T5240 Servers Installation Guide • February 2008...
  • Page 85 Chapter 3 Powering On the System...
  • Page 86 SPARC Enterprise T5140 and T5240 Servers Installation Guide • February 2008...

  • Page 87: Updating The Firmware

    A P P E N D I X Updating the Firmware This appendix provides instructions for updating SP firmware. “The flashupdate command” on page 61 ■ “Updating the Firmware” on page 61 ■ The flashupdate command The flashupdate command updates both the service processor firmware and the server firmware.

  • Page 88: To Update The Firmware

    The load command updates the service processor flash image and the host firmware. The load command requires the following information: IP address of a TFTP server on the network that can access the flash image ■ SPARC Enterprise T5140 and T5240 Servers Installation Guide • February 2008...
  • Page 89 Full path name to the flash image that the IP address can access ■ The command usage is as follows: load [-script] -source tftp://xxx.xxx.xx.xx/pathname where: -script – Does not prompt for confirmation and acts as if yes was specified ■ -source –...
  • Page 90 Starting system log daemon: syslogd and klogd. Starting periodic command scheduler: cron. Starting IPMI Stack..Done. Starting OpenBSD Secure Shell server: sshd. Starting Servicetags listener: stlistener. Starting FRU update program: frutool. hostname login: SPARC Enterprise T5140 and T5240 Servers Installation Guide • February 2008...

  • Page 91: Selecting A Boot Device

    SPARC Enterprise T5140 and T5240 Servers Administration Guide. Note – The serial management port on the ILOM card is preconfigured as the default system console port. For more information, see the SPARC Enterprise T5140 and T5240 Servers Overview. If you want to boot from a network, you must connect the network interface to the...

  • Page 92: To Select A Boot Device

    The show-devs command lists the system devices and displays the full path name of each PCI device. SPARC Enterprise T5140 and T5240 Servers Installation Guide • February 2008...

  • Page 93: Installing The Servers With The Express Rail Rackmounting Kit

    The kit and the installation procedures are the same for both the SPARC Enterprise T5140 and T5240 servers. Note – If your rackmount kit came with its own instructions, use the instructions in your rackmount kit instead of the instructions in this appendix.

  • Page 94: Slide Rail Assembly Notes For The Express Rail Rackmounting Kit

    24 in. (61 cm) to 36.5 in. (93 cm). The front section can be extended to allow movement of the server out of the rack. SPARC Enterprise T5140 and T5240 Servers Installation Guide • February 2008...
  • Page 95 The removable mounting bracket slides 14.5 in. (37 cm) out of the slide rail, then ■ locks in place. If you unlock the mounting bracket at this point, it slides an additional 14.5 in. (37 cm) before separating from the slide rail. You can then mount the mounting bracket to the right or left side of the server chassis.

  • Page 96: Figure C-2 Locating The Locks On The Slide Rail Assembly For The Sparc Enterprise T5240 Server

    Locating the Locks on the Slide Rail Assembly for the SPARC Enterprise FIGURE C-2 T5240 Server SPARC Enterprise T5140 and T5240 Servers Installation Guide • February 2008...

  • Page 97: Installing The Servers In A Rack With Express Rails

    Installing the Servers in a Rack With Express Rails Note – Ensure that you have all of the parts in the rackmount kit before you begin the installation of the server. The rackmount kit contains two slide rail assemblies, which can be installed on either the right or left side of the rack.

  • Page 98: Figure C-3 Unlocking The Express Rail Slide Rail Assembly

    Unlocking the Express Rail Slide Rail Assembly FIGURE C-3 b. Pull the mounting bracket out until it stops. SPARC Enterprise T5140 and T5240 Servers Installation Guide • February 2008...

  • Page 99: Figure C-4 Express Rail Mounting Bracket Release Button

    c. Slide the mounting bracket release button to the left ( ), then slide FIGURE C-4 the mounting bracket completely out of the slide rail. Express Rail Mounting Bracket Release Button FIGURE C-4 Appendix C Installing the Servers With the Express Rail Rackmounting Kit...

  • Page 100: Figure C-5 Attaching An Express Rail Mounting Bracket To The Chassis

    3. Attach the second mounting bracket to the left side of the server chassis. 4. Orient slide rails, ensuring that the ball bearing tracks (labeled FRONT) are forward ( FIGURE C-6 SPARC Enterprise T5140 and T5240 Servers Installation Guide • February 2008...

  • Page 101: Figure C-6 Express Rail Slide Rails Orientation For Installation

    Express Rail Slide Rails Orientation for Installation FIGURE C-6 Appendix C Installing the Servers With the Express Rail Rackmounting Kit...

  • Page 102: Figure C-7 Attaching Express Slide Rails To The Rack

    Caution – Deploy the antitilt feature on the rack before continuing the installation. ▼ To Insert and Lock the Server in the Rack 1. Deploy the antitilt feature, if the rack is so equipped. SPARC Enterprise T5140 and T5240 Servers Installation Guide • February 2008...

  • Page 103: Figure C-8 Inserting Express Rail Mounting Brackets Into The Slide Rails

    Caution – The weight of the servers on extended slide rails can be enough to overturn an equipment rack. Caution – The 2U server weighs approximately 46 lb (20.7 kg). Two people are required to lift and mount the server into a rack enclosure when using the procedures in this chapter.

  • Page 104: Figure C-9 Sliding The Express Rail Release Tab And Securing The Server In The Rack

    Sliding the Express Rail Release Tab and Securing the Server in the Rack FIGURE C-9 Caution – Before continuing, verify that the server is securely mounted in the rack, and that the slide rails are locked in the mounting brackets. SPARC Enterprise T5140 and T5240 Servers Installation Guide • February 2008...

  • Page 105: Installing The Cable Management Arm

    Caution – To prevent damage to your server, do not move the rack while the server is mounted. To install or replace internal parts in the server, you must first remove the server from the rack. For the removal procedure, refer to the SPARC Enterprise T5140 and T5240 Servers Service Manual. Appendix C...
  • Page 106 SPARC Enterprise T5140 and T5240 Servers Installation Guide • February 2008...

  • Page 107: Index

    Index Symbols console command, 58 #. escape sequence for system console, 58 DB-9 TTY connector, 7 definitions, See terms, 15 accessing ILOM command line, 45 deinstallation of server, 79 adapters for serial cables, 32 device identifiers, listed, 55 address, IP, 4 diagnostics, when run, 41 addresses, web, See web sites admin login, setting password for, 46...
  • Page 108 3 on, 5 standby voltage, 3.3v, 41 stop bit, 38 parity for serial terminal, no, 38 system console escape sequence #., 58 password command, 45 SPARC Enterprise T5140 and T5240 Servers Installation Guide • February 2008...
  • Page 109 terms left and right sides, 15 slide rail assembly, 10, 68 TTYA serial port, 7 uadmin command, 57 unlocking mounting bracket, 71 web site http://manuals.fujitsu-siemens.com/, xv Index...
  • Page 110 SPARC Enterprise T5140 and T5240 Servers Installation Guide • February 2008...
  • Page 112 Herausgegeben von / Published by Fujitsu Siemens Computers GmbH Bestell-Nr./ Order No.: U41767-J-Z816-1-76 *U41767-J-Z816-1-76 * U41767-J-Z816-1-76...

This manual is also suitable for:

Sparc enterprise t5240

Table of Contents