Table of Contents
Advertisement
Parameters (Read/Write)
The following table lists user accessible parameters for the F7 drive.
■
The "Prm" column contains the parameter name.
■
The "Addr" column contains the register address in hexadecimal format. F7 drive registers are always referred in hexadecimal format.
■
The "Data" column contains the available selections for those parameters whose value is selected from a list. If the Data column is
empty, that parameter's value is entered as a number within the limits shown in the "± Limits / Selection"
■
The "+/- Limits / Selection" column contains:
▪
The name of the selection if the Data column is not empty
▪
The upper and lower limits of the data that can be entered for that parameter
■
The "Inc" column describes the smallest increment with which the parameter value may be changed. Since all parameter values are
sent and received as whole numbers, the "Inc" value also describes how that value should be scaled.
■
The "RUN" column describes whether the parameter is able to be written while the RUN command is active.
▪
"Y" - the parameter is writable during RUN
■
The "Acs" columns describe the accessibility
▪
"A" - the parameter requires Advanced access (A1-01 = 2)
▪
"O" - the parameter has Operation access (A1-01 = 0)
▪
"F" – the parameter requires factory access
▪
"N" – the parameter is not accessible
■
The "Dep" column shows whether the value, definition or function of the selected parameter is dependent on the setting of another
parameter. If there is an "*" in the "Dep" column, refer to the appropriate table at the end of this section.
Notes:
■
Factory parameters are shown shaded and are included here for information purposes only
■
Parameter defaults are listed for the F7U drive.
■
All parameters are sent and received as whole numbers regardless of how they are represented in the "+/- Limits / Selection" column
or their increment. For example, parameter b4-01, Delay-ON Timer, has limits of 0.0 ~ 3000.0 seconds with an increment of 0.1
seconds. If parameter b4-01 is read and a value of 600 returned, the actual value is 60.0 seconds. If parameter b4-01 is to be set to 30
seconds, a value of 300 (30.0 seconds) must be sent.
Prm
Adr
Function
A1-00 0100h
Select Language
A1-01 0101h
Access Level
A1-03 0103h
Init Parameters
A1-04 0104h
Enter Password
A2-01 0106h
User Param 1
A2-02 0107h
User Param 2
A2-03 0108h
User Param 3
A2-04 0109h
User Param 4
A2-05 010Ah
User Param 5
A2-06 010Bh
User Param 6
A2-07 010Ch
User Param 7
A2-08 010Dh
User Param 8
A2-09 010Eh
User Param 9
A2-10 010Fh
User Param 10
A2-11 0110h
User Param 11
A2-12 0111h
User Param 12
A2-13 0112h
User Param 13
A2-14 0113h
User Param 14
A2-15 0114h
User Param 15
A2-16 0115h
User Param 16
A2-17 0116h
User Param 17
A2-18 0117h
User Param 18
A2-19 0118h
User Param 19
A2-20 0119h
User Param 20
A2-21 011Ah
User Param 21
A2-22 011Bh
User Param 22
A2-23 011Ch
User Param 23
Data
0
English
1
Japanese
2
Deutsch
3
Français
4
Italiano
5
Español
6
Português
0
Operation Only
2
Advanced Level
616
Factory Level
0
No Initialize
2220
2-Wire Initial
3330
3-Wire Initial
0 ~ 9999
0h ~ 5ffh
0h ~ 5ffh
0h ~ 5ffh
0h ~ 5ffh
0h ~ 5ffh
0h ~ 5ffh
0h ~ 5ffh
0h ~ 5ffh
0h ~ 5ffh
0h ~ 5ffh
0h ~ 5ffh
0h ~ 5ffh
0h ~ 5ffh
0h ~ 5ffh
0h ~ 5ffh
0h ~ 5ffh
0h ~ 5ffh
0h ~ 5ffh
0h ~ 5ffh
0h ~ 5ffh
0h ~ 5ffh
0h ~ 5ffh
0h ~ 5ffh
E7 Drive Parameters 4-11
Limits / Selections
Addresses for parameters b1-01 ~ 03-01
Inc
Default
Run Acs Dep
1
0
Run O
1
2
Run A
1
0
A
1
0
O
1
0h
A
1
0h
A
1
0h
A
1
0h
A
1
0h
A
1
0h
A
1
0h
A
1
0h
A
1
0h
A
1
0h
A
1
0h
A
1
0h
A
1
0h
A
1
0h
A
1
0h
A
1
0h
A
1
0h
A
1
0h
A
1
0h
A
1
0h
A
1
0h
A
1
0h
A
1
0h
A
Advertisement
Table of Contents
