All-carrier rv cellular signal booster kit (12 pages)
Summary of Contents for SureCall Force5 Inline
Page 1
Force5 Inline 5-Band Cellular Booster Extender for Commercial Offices, Institutions and Housing Complexes. User Guide WARNING This is NOT a CONSUMER device. It is designated for installation by FCC LICENSEES and QUALIFIED INSTALLERS. You MUST have an FCC LICENSE or express consent of an FCC Licensee to operate this device.
• For areas consisting of long aisles, Force5 Inline boosters can be added where the signal falls to between -70dB and -90dB. • For large, wide areas the Force5 Inline boosters can be daisy-chained with the use of splitters to extend the signal to remote corners.
Step 2. Make sure you have sufficient cable length between the main cable location and booster connector. Step 3 Make sure you have sufficient cable length between proposed inside antenna location and booster connector. SureCall | 48346 Milmont Drive, Fremont CA 94538 | 1-888-365-6283 | sales@surecall.com...
Point the antenna away from the outside antenna. To avoid interference stay a minimum distance of 3 feet from the panel antenna. Force5 Industrial Force5 Inline SureCall | 48346 Milmont Drive, Fremont CA 94538 | 1-888-365-6283 | sales@surecall.com...
Page 6
Step 4: Tighten fixing nut to secure antenna (do not over-tighten). • Storage and transportation: Store and place in non-extreme room-temperature and dry environment • Attention: This antenna should not be used near open fire or flame SureCall | 48346 Milmont Drive, Fremont CA 94538 | 1-888-365-6283 | sales@surecall.com...
Note: If the Power LED does not turn ON or the Alert LEDs continue to flash, see Troubleshooting page 19. This booster is rated for 19V AV input voltage. DO NOT use the booster with a higher voltage power supply. This can damage the booster, cause persoanl injury and viod your warrenty. SureCall | 48346 Milmont Drive, Fremont CA 94538 | 1-888-365-6283 | sales@surecall.com...
Page 8
Installing your Hardware Booster Hardware The following image shows the key hardware components on the cellullar booster. Refer to this image as you install your Force5 Inline kit components. N connector to inside antenna Power Switch Mount Kit Power Jack...
DIP switches in the same bank being set to ON. WARNING: Do not adjust the uplink and downlink dB attenuation settings more than 20dB. This could cause the booster to shut down SureCall | 48346 Milmont Drive, Fremont CA 94538 | 1-888-365-6283 | sales@surecall.com...
Page 10
LTE 781 Uplink ON = LTE Verizon uplink warning. Power off booster immediately. OFF = normal operation. Cellular 800 ON = Cellular uplink warning. Uplink Power off booster immediately. SureCall | 48346 Milmont Drive, Fremont CA 94538 | 1-888-365-6283 | sales@surecall.com...
Page 11
• Increase the distance between the outside and inside antennas. Be sure your signal booster’s dB gain is turned up to maximum gain on each dial (see page 16). SureCall | 48346 Milmont Drive, Fremont CA 94538 | 1-888-365-6283 | sales@surecall.com...
The Power LED does not Be sure the AC outlet is working and is not controlled by a wall turn ON switch that can cut power to the outlet. SureCall | 48346 Milmont Drive, Fremont CA 94538 | 1-888-365-6283 | sales@surecall.com...
SureCall warrants to the Buyer that each of its products, when shipped, will be free from defects in material and workman- ship, and will perform in full accordance with applicable specifications. The limit of liability under this warranty is, at SureCall’s...
SureCall has made a good faith effort to ensure the accuracy of the information in this document and disclaims the implied warranties of merchantability and fitness for a particular purpose and makes no express warranties, except as may be stated in its written agreement with and for its customers.SureCall shall not be held liable to anyone for any indirect, special or consequential damages due to omissions or...
Need help?
Do you have a question about the Force5 Inline and is the answer not in the manual?
Questions and answers