Advertisement

FOR QUALIFIED INSTALLER ONLY. This basic Installation Sheet is an initial release. If a complete Operations
Manual (for the unit being installed) is required or needed, please refer to the Lancer web site (lancercorp.com) for
immediate access, or for your convenience, scan this QR code with a mobile device (app required) for immediate
access to other Technical Documents and alternative translations (if available) pertaining to this unit. Contact Lancer
Customer Service for assistance as required.
ABOUT THIS MANUAL
This booklet is an integral and essential part of the product and
should be handed over to the operator after the installation and
preserved for any further consultation that may be necessary.
Please read carefully the guidelines and warnings contained
herein as they are intended to provide the user with essential
information for the continued safe use and maintenance of the
product. In addition, it provides GUIDANCE ONLY to the user on
the correct services and site location of the unit.
The installation and relocation, if necessary, of this product must be carried out by qualified personnel with
up-to-date safety and hygiene knowledge and practical experience, in accordance with current regulations.
IMPORTANT SAFETY INSTRUCTIONS
! Intended Use
The dispenser is for indoor use only. This unit is not a toy. Children should not be supervised not to play with appliance. It should
not be used by children or infirm persons without supervision. This appliance is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a person responsible for their safety. Cleaning and user maintenance
shall not be performed by children without supervision. The min/max ambient operating temperature for the dispenser is 40°F to
90°F (4°C to 32°C). Do not operate unit below minimum ambient operation conditions. Should freezing occur, cease operation of
the unit and contact authorized service technician. Service, cleaning and sanitizing should be accomplished only by trained
personnel. Applicable safety precautions must be observed. Instruction warnings on the product being used must be followed.
! Automatic Agitation
Units are equipped with an automatic agitation system and will activate unexpectedly. Do not place hands or foreign objects in the
ice bin. Unplug the dispenser during servicing, cleaning, and sanitizing. To avoid personal injury, do not attempt to lift the dispenser
without assistance. For heavier dispensers, use a mechanical lift.
®
FS22
FS30
Flavor Select (FS) - 22/30
BEFORE GETTING STARTED
Each unit is tested under operating conditions and is thoroughly
inspected before shipment. At the time of shipment, the carrier
accepts responsibility for the unit. Upon receiving the unit,
carefully inspect the carton for visible damage. If damage exists,
have the carrier note the damage on the freight bill and file a
claim with carrier. Responsibility for damage to the dispenser lies
with the carrier.
LANCER INSTALLATION GUIDE
Revision: March 2018
Lancer PN: 28-0737/04

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the FS 22 and is the answer not in the manual?

Questions and answers

Summary of Contents for lancer FS 22

  • Page 1 FOR QUALIFIED INSTALLER ONLY. This basic Installation Sheet is an initial release. If a complete Operations Manual (for the unit being installed) is required or needed, please refer to the Lancer web site (lancercorp.com) for immediate access, or for your convenience, scan this QR code with a mobile device (app required) for immediate access to other Technical Documents and alternative translations (if available) pertaining to this unit.
  • Page 2: Specifications

    F Electrical Warning Check the dispenser name plate label, located behind the splash plate, for the correct electrical requirements of unit. Do not plug into a wall electrical outlet unless the current shown on the serial number plate agrees with local current available. Follow all local electrical codes when making connections.
  • Page 3: Read This Manual

    READ THIS MANUAL This manual was developed by the Lancer Corporation as a reference for the owner/operator and installer of this dispenser. Please read this guide before installation and operation of this dispenser. If service is required please call your Lancer Service Agent or Lancer Customer Service.
  • Page 4: Inspection Of Drain Spider

    Locate drain spider and reinstall in the cold-plate cavity NOTE where drain line exits. Reinstall all components. Ensure agitator clip is locked. Lancer does NOT recommend the use of shaved or flake ice in the dispenser. The ice level should not exceed the height of the metal bin wall when filled manually. Unit may be installed directly on counter-top or on legs. If installed directly on the counter, unit must be sealed to the counter-top with an FDA approved sealant.
  • Page 5: Dispenser Installation

    Connect tubing to water source then flush water lines to check for leaks. An adapter plate is required when installing an ice maker. Contact your Sales Representative or Lancer Customer Route appropriate tubing from the remote pump location to Service for more information.
  • Page 6: Installing Remote Syrup Pumps

    Tube to become clogged. 10. Reattach Drip Tray/Cup Rest to unit. Remote Pump Installation If necessary, install water booster (Lancer PN MC-163172) between water supply and the unit. Using tubing cutters, cut water line and install tee fitting, then route appropriate tubing from the remote pump location to the tee fitting at water line.
  • Page 7: Dispenser Setup

    Installing CO Supply Using a wrench, loosen lock nut on the regulator adjustment screw of the high pressure CO regulator connected to the Connect high pressure CO regulator assembly to CO source, then using a screwdriver back out lock nut screw all cylinder or bulk system.
  • Page 8: Adjust Water Flow Rate & Syrup/Water Ratio

    Turn on CO at the source then, using a screwdriver, adjust Using a Lancer ratio cup verify water flow rate. Use a the high pressure regulator at the source to 110 PSI (0.758 screwdriver to adjust if needed. MPA) then tighten locknut with wrench.
  • Page 9: Cleaning And Sanitizing

    CLEANING AND SANITIZING General Information Other Supplies Needed • Lancer equipment (new or reconditioned) is shipped from Clean cloth towels Sanitary gloves the factory cleaned and sanitized in accordance with NSF Bucket Small brush (PN 22-0017) guidelines. The operator of the equipment must provide...
  • Page 10: Cleaning And Sanitizing Syrup Lines - Bag In Box

    Cleaning and Sanitizing Syrup Lines - Bag in Box Ice Chute Cleaning NOTE Disconnect syrup lines from BIB’s Place syrup lines, with BIB connectors, in a bucket of warm It is recommended to perform this procedure monthly, water. or more often if desired. Use the cleaning solution described above.
  • Page 11: Plumbing Diagram

    VALVE HARNESS IS2-1 IS2-2 IS1-3 IS1-2 IS2-3 IS1-1 DIAGRAM S2-4 S2-3 S2-1 S1-4 S1-2 S1-1 SODA2 S2-2 WATER2 WATER1 S1-3 SODA1 IS2-1 IS1-1 S1-1 S1- 3 S2-1 S2- 3 IS2-2 IS1-2 S1- 2 S2-2 S2- 4 S1- 4 IS1-3 IS2-3 IS2- 3 IS2- 2 IS2- 1 IS1- 3 IS1- 2...
  • Page 12 Wiring and Plumbing Diagrams - FS22 International...
  • Page 13 Wiring and Plumbing Diagrams - FS30...
  • Page 14 INTENTIONALLY LEFT BLANK...
  • Page 15: Dispenser Disposal

    Dispenser Disposal To prevent possible harm to the environment from improper disposal, recycle the unit by locating an authorized recycler or contact the retailer where the product was purchased. Comply with local regulations regarding disposal of the refrigerant and insulation.
  • Page 16 Lancer Corp. 800-729-1500 Technical Support/Warranty: 800-729-1550 custserv@lancercorp.com lancercorp.com...

This manual is also suitable for:

Fs 30

Table of Contents