Sony HXC-FB80 Operating Instructions Manual page 22

Once the area setting is complete, set the current date and time.
Note
The camera cannot be used if the area of use is not set.
Setting the area of use
1
Turn on the camera.
The screen for setting the area of use appears in the viewfinder.
F O R M A T
C O U N T R Y : N O T
S Y S T E M
S Y S T E M S C
S E T F O R M A T
A N D T U R N
2
Press the menu control knob.
The area of use becomes selectable.
F O R M A T
C O U N T R Y : N O T
S Y S T E M
S Y S T E M S C
S E T F O R M A T
A N D T U R N
3
Rotate the menu control knob to select the area of use.
Setting Area of use
NTSC(J) NTSC area
AREA (Japan)
NTSC AREA NTSC area (for
areas other than
Japan)
PAL AREA PAL area
4
Change the SYSTEM LINE (video resolution) and
SYSTEM SCAN (video scanning mode) settings according
to the video format you are using.
SYSTEM LINE
Setting Resolution (Horizontal × Vertical)
1080 1080 lines (1920×1080)
720 720 lines (1280×720)
SYSTEM SCAN
Setting Video scanning mode
Interlace Interlaced
Progressive Progressive
PsF Progressive
Supported formats: 1080/59.94i, 1080/59.94P, 1080/50i,
1080/50P, 1080/29.97PsF, 1080/25PsF, 1080/23.98PsF,
720/59.94P, 720/50P
5
Turn the camera off and then back on.
The camera is now ready for use.
S E T T I N G
S E L E C T E D
L I N E : 1 0 8 0
A N : I n t e r l a c e
O F F O N C E .
S E T T I N G
? S E L E C T E D
L I N E : 1 0 8 0
A N : I n t e r l a c e
O F F O N C E .
Output composite System
signal frequency
NTSC signal 59.94i
without setup
NTSC signal with 59.94i
setup (7.5IRE)
PAL signal 50i
To change the area of use
Change the setting using COUNTRY on the <OUTPUT FORMAT>
page in the MAINTENANCE menu.
Note
The setting is switched to the CCU setting when a CCU is connected.
Setting the date/time
Set the built-in clock to the current local time on the <DATE> page
in the MAINTENANCE menu.
For details about menu operations, see "Menu Operation"
(page 34).
1
Turn on the camera.
2
Press and hold the menu control knob and set the
DISPLAY/MENU switch to MENU.
The camera enters menu mode, and "TOP" is displayed at the
upper-right corner of the screen.
3
Rotate the menu control knob to align the , pointer with
TOP and press the menu control knob.
The TOP MENU screen is displayed.
<TOP MENU>
USER
c
USER MENU CUSTOMIZE
ALL
OPERATION
PAINT
MAINTENANCE
FILE
DIAGNOSIS
4
Rotate the menu control knob to align the , pointer with
MAINTENANCE and press the menu control knob.
The CONTENTS page of the MAINTENANCE menu appears.
CONTENTS
xx
01.<AUTO SETUP>
c
02.<WHITE SHADING>
03.<BLACK SHADING>
04.<AUTO IRIS>
05.<LENS>
06.<CIS COMP>
07.<AUDIO>
08.<CALL/TALLY>
09.<OUTPUT FORMAT>
10.<TEST OUT>
11.<SDI OUT>
12.<TRUNK>
13.<GENLOCK>
14.<DATE>
5
Rotate the menu control knob to scroll the page and align
the , pointer with <DATE> and press the menu control
knob.
The <DATE> page appears.
Press the menu control knob to confirm the page selection.
22
M00 TOP