Leg & Caster Installation - Delfield Specification Line GADTR1P-SH Original Instructions Service Manual

Section 2
Refrigeration
Model Heat of
Rejection (BTU)
Reach-In Dual Temperature
GADBR1P-SH Ref. 232
GADTR1P-SH Frzr. 401
GADFL2P-S Ref. 420
GADRL2P-S Frzr. 790
Reach-In Freezer
GAF1P-S(H) 790
GAF2P-S(H) 1380
GAF3P-S(H) 1800
Pass-Thru Freezer
GAFPT1P-S(H) 930
GAFPT2P-S(H) 1630
Roll-In Freezer
GAFRI1P-S 1401
GAFRI2P-S 2458
Narrow Reach-In Refrigerator
GAR1NP-G(H) 540
GAR1NP-S(H) 390
GAR2NP-G(H) 890
GAR2NP-S(H) 590
Reach-In Refrigerator
GAR1P-G(H) 570
GAR1P-S(H) 420
GAR2P-G(H) 930
GAR2P-GL 1606
GAR2P-S(H) 620
GAR3P-G(H) 1400
GAR3P-S(H) 940
Reach-In Fishfile
GARFF1P-D 570
Pass-Thru Refrigerator
GARPT1P-G(H) 690
GARPT1P-S(H) 460
GARPT2P-G(H) 1260
GARPT2P-S(H) 800
Roll-In Refrigerator
GARRI1P-G 800
GARRI1P-S 680
GARRI2P-G 1460
GARRI2P-S 1230
Roll-Thru Refrigerator
GARRT1P-S 830
GARRT2P-S 1530
Part Number GA_SM 08/18
BTU/Hour R290
Capacity Charge
Ref. 1431 Ref. 78g
Frzr. 1094 Frzr. 62g
Ref. 1920 Ref. 113g
Frzr. 2035 Frzr. 93g
2035 93g
2485 109g
4070 (2X)110g
2035 93g
4070 (2X)110g
2261 109g
4523 (2X)110g
1860 113g
1860 113g
2470 113g
2470 113g
1920 113g
1920 113g
2540 113g
3370 113g
2540 113g
3865 118g
3865 118g
1920 113g
1860 113g
1860 113g
3760 113g
3760 113g
2470 113g
2470 113g
3760 118g
3760 118g
2470 113g
3760 118g
Leg & Caster Installation
n
The unit must be installed in a stable condition with
the front wheels locked. Locking the front casters after
installation is the owner's and operator's responsibility.
n
Use a jack to lift the refrigeration unit off the ground
just far enough to remove the leg/caster. Place blocking
underneath the unit. Do not work underneath a raised
unit without proper blocking. Do not lift the unit more
than necessary to remove the leg/caster. Lifting the unit
too far can make the unit unstable.
,
All single-section units require that the swivel casters be
mounted on the front and rigid casters be mounted on
the rear.
To install the legs or casters:
1. Remove unit from skid.
NOTE: The bolts used to hold the unit to the skid should
be re-used as the fourth hex head bolt for each caster or
leg plate installation. The bolt should not measure over
2" (5cm) in length.
2. Raise unit to access leg/caster mounting holes on
bottom of unit.
3. Attach the legs or casters to bottom of cabinet using hex
head bolts.
Installation
Warning
Warning
Caution
11