Siemens MICROMASTER 411 Operating Instructions Manual page 77

Issue 03/01
Alarms and Warnings (P0004 = 21)
ParNr
P0952
r0947[8]
r0949[8]
r0948[12]
P2100[3]
P2101[3]
P2111
r2110[4]
r2114[2]
P2150[1]
P2155[1]
P2156[1]
P2164[1]
P2167[1]
P2168[1]
P2170[1]
P2171[1]
P2172[1]
P2173[1]
P2179
P2180
r2197
PI Controller (P0004=22)
ParNr
P2200[1]
P2201[1]
P2202[1]
P2203[1]
P2204[1]
P2205[1]
P2206[1]
P2207[1]
P2216
P2217
P2218
r2224
P2231[1]
P2232
P2240[1]
r2250
P2253[1]
P2254[1]
MICROMASTER 411 & COMBIMASTER 411
6SE6400-5CA00-0BP0
ParText
Total number of faults
Last fault code
Fault value
Fault time
Alarm number selection
Stop reaction value
Total number of warnings
Warning number
Run time counter
Hysteresis frequency f_hys
Threshold frequency f_1
Delay time of threshold freq f_1
Hysteresis frequency deviation
Switch-off frequency f_off
Delay time T_off
Threshold current I_thresh
Delay time current
Threshold DC-link voltage
Delay time DC-link voltage
Current limit for no load ident.
Delay time for load missing
CO/BO: Monitoring word 1
ParText
BI: Enable PID controller
Fixed PID setpoint 1
Fixed PID setpoint 2
Fixed PID setpoint 3
Fixed PID setpoint 4
Fixed PID setpoint 5
Fixed PID setpoint 6
Fixed PID setpoint 7
Fixed PID setpoint mode - Bit 0
Fixed PID setpoint mode - Bit 1
Fixed PID setpoint mode - Bit 2
CO: Act. fixed PID setpoint
Setpoint memory of PID-MOP
Inhibit rev. direct. of PID-MOP
Setpoint of PID-MOP
CO: Output setpoint of PID-MOP
CI: PID setpoint
CI: PID trim source
Operating Instructions
5 System Parameters
Default Acc WS
0 3 CT
- 2 -
- 3 -
- 3 -
0 3 CT
0 3 CT
0 3 CT
- 2 -
- 3 -
3.00 3 CUT
30.00 3 CUT
10 3 CUT
3.00 3 CUT
1.00 3 CUT
10 3 CUT
100.0 3 CUT
10 3 CUT
800 3 CUT
10 3 CUT
3.0 3 CUT
2000 3 CUT
- 2 -
Default Acc WS
0:0 2 CUT
0.00 2 CUT
10.00 2 CUT
20.00 2 CUT
30.00 2 CUT
40.00 2 CUT
50.00 2 CUT
60.00 2 CUT
1 3 CT
1 3 CT
1 3 CT
- 2 -
0 2 CUT
1 2 CT
10.00 2 CUT
- 2 -
0:0 2 CUT
0:0 3 CUT
QC
N
-
-
-
N
N
N
-
-
N
N
N
N
N
N
N
N
N
N
N
N
-
QC
N
N
N
N
N
N
N
N
N
N
N
-
N
N
N
-
N
N
77