Siemens MICROMASTER 411 Operating Instructions Manual page 74

5 System Parameters
ParNr
P1060[1]
P1061[1]
P1070[1]
P1071[1]
P1075[1]
P1076[1]
r1078
r1079
P1080[1]
P1082[1]
P1091[1]
P1092[1]
P1093[1]
P1094[1]
P1101[1]
r1114
r1119
P1120[1]
P1121[1]
P1130[1]
P1131[1]
P1132[1]
P1133[1]
P1134[1]
P1135[1]
r1170
Drive Features (P0004 = 12)
ParNr
P0005[1]
P0006
P0007
P0011
P0012
P0013[20]
P1200
P1202[1]
P1203[1]
P1210
P1211
P1215
P1216
P1217
P1232[1]
P1233[1]
74
ParText
JOG ramp-up time
JOG ramp-down time
CI: Main setpoint
CI: Main setpoint scaling
CI: Additional setpoint
CI: Additional setpoint scaling
CO: Total frequency setpoint
CO: Selected frequency setpoint
Min. frequency
Max. frequency
Skip frequency 1
Skip frequency 2
Skip frequency 3
Skip frequency 4
Skip frequency bandwidth
CO: Freq. setp. after dir. ctrl.
CO: Freq. setpoint before RFG
Ramp-up time
Ramp-down time
Ramp-up initial rounding time
Ramp-up final rounding time
Ramp-down initial rounding time
Ramp-down final rounding time
Rounding type
OFF3 ramp-down time
CO: Frequency setpoint after RFG
ParText
Display selection
Display mode
Backlight delay time
Lock for user defined parameter
Key for user defined parameter
User defined parameter
Flying start
Motor-current: Flying start
Search rate: Flying start
Automatic restart
Number of restart attempts
Holding brake enable
Holding brake release delay
Holding time after ramp down
DC braking current
Duration of DC braking
MICROMASTER 411 & COMBIMASTER 411
Issue 03/01
Default Acc WS
10.00 2 CUT
10.00 2 CUT
755:0 3 CT
1:0 3 CT
755:1 3 CT
1:0 3 CT
- 3 -
- 3 -
0.00 1 CUT
50.00 1 CT
0.00 3 CUT
0.00 3 CUT
0.00 3 CUT
0.00 3 CUT
2.00 3 CUT
- 3 -
- 3 -
10.00 1 CUT
10.00 1 CUT
0.00 2 CUT
0.00 2 CUT
0.00 2 CUT
0.00 2 CUT
0 2 CUT
5.00 2 CUT
- 3 -
Default Acc WS
21 2 CUT
2 3 CUT
0 3 CUT
0 3 CUT
0 3 CUT
0 3 CUT
0 2 CUT
100 3 CUT
100 3 CUT
1 2 CUT
3 3 CUT
0 2 T
1.0 2 T
1.0 2 T
100 2 CUT
0 2 CUT
Operating Instructions
6SE6400-5CA00-0BP0
QC
N
N
N
N
N
N
-
-
Q
Q
N
N
N
N
N
-
-
Q
Q
N
N
N
N
N
Q
-
QC
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N