Table of Contents
Advertisement
4.
Auxiliary Input Delay* - (All modes)
"AUX IN" (Figure 54) programming is required only if the AUX In terminal
is being used (Such as with a differential pressure switch). This estab-
lishes the uninterrupted period of time (in seconds) that a signal must
be received through the auxiliary input before the controller is to react
by initiating a regeneration sequence. The default time is (6) seconds.
Note that this feature is ignored if nothing is connected to the AUX input
terminal.
To adjust the seconds setting, use the "-" or "+" keys to scroll to the
desired number of seconds. (Adjustable from 0 to 999 seconds). Pressing
the "-" or "+" keys for 3 seconds or more will cause the digits to scroll rap-
intervals greater than one at a time. Pressing the Status
idly and at
key will save the setting and move to the next programming step.
5.
Cycle 1 Time* - (All modes)
The backwash cycle is represented by "bw 10" (Figure 55) in the display.
The default duration of cycle 1 is 10 minutes. To adjust the minutes set-
ting, use the "-" or "+" keys to scroll to the desired number of minutes.
(Adjustable from 1 to 99 minutes). Pressing the "-" or "+" keys for 3 sec-
onds or more will cause the digits to scroll rapidly and at intervals greater
than one at a time. Pressing the Status key will save the setting and move
to the next programming step.
6.
Cycle 2 Time* - (All modes except if Brine Reclaim DIP switch 10 is set
to ON)
The brine/slow rinse cycle is represented by "br 60" (Figure 56) in the
display. The default duration of cycle 2 is 60 minutes if the DIP switch #7
is OFF (softener) or 2 minutes if DIP switch #7 is ON (filter). To adjust the
minutes setting, use the "-" or "+" keys to scroll to the desired number of
minutes. Pressing the "-" or "+" keys for 3 seconds or more will cause the digits to scroll rapidly and at intervals
greater than one at a time. Pressing the Status key will save the setting and move to the next programming step.
7.
Cycle 3 Time* - (All modes)
The fast rinse cycle is represented by "Fr 10" (Figure 57) in the display.
The default duration of cycle 3 is 10 minutes. To adjust the minutes set-
ting, use the "-" or "+" keys to scroll to the desired number of minutes.
(Adjustable from 1 to 99 minutes). Pressing the "-" or "+" keys for 3 sec-
onds or more will cause the digits to scroll rapidly and at intervals greater
than one at a time. Pressing the Status key will save the setting and move
to the next programming step.
8.
Regeneration Interval* - Active only if no meter and/or Aqua-Sensor is
detected OR if DIP switch #6 is ON.
The display will show the REGEN icon and "days 03" (Figure 58) (if DIP
switch 8 is OFF) or REGEN and "Hour 12" if DIP switch 8 is ON.
The default setting for "days" is "03" while the "Hour" default is "12" (Fig-
ure 59).
To adjust the "day" or "Hour" setting, use the "-" or "+" keys to scroll
to the desired setting. (Adjustable from 1 to 99 days or 1 to 24 hours).
Pressing the "-" or "+" keys for 3 seconds or more will cause the digits
to scroll rapidly and at intervals greater than one at a time. Pressing the
Status key will save the setting and move to the next programming step.
NOTE
Single systems that are set with DIP switch 8 OFF and without a meter or Aqua-Sensor device con-
nected will offer the following OPTIONAL time clock setting to be displayed. (Figure 60)
Cat. No. 01016449
Figure 54.
Figure 55.
Figure 56.
Figure 57.
Figure 58.
Figure 59.
Figure 60.
Programming
37
Hide quick links:
Advertisement
Table of Contents
