Page 1
USER USER IVH-9200 Manual Manual Quad Core Intel ® Xeon ® / Core ™ i7/i5/i3 Vehicle Computing System Workstation-grade, Rugged, Fanless, -40°C to 75°C Operation 1.2.0 Edition 20181116...
Page 2
Record of Revision Version Date Page Description Remark 05/05/2017 Official Release 05/05/2017 Update 11/16/2018 Update...
Page 3
This manual is released by Vecow Co., Ltd. for reference purpose only. All product offerings and specifications are subject to change without prior notice. It does not represent commitment of Vecow Co., Ltd. Vecow shall not be liable for direct, indirect, special, incidental, or consequential damages arising out of the use of the product or documentation or any infringements upon the rights of third parties, which may result from such use.
Page 4
Order Information Part Number Description IVH-9200, 6 GigE LAN w/4 A-coded M12 PoE , 4 SSD Tray, IVH-9200M 8 USB 3.0, 4 COM, 3 SIM, 32 Isolated DIO IVH-9200, 6 GigE LAN w/4 PoE , 4 SSD Tray, 8 USB 3.0,...
Page 5
Part Number Description ® 7th Gen Intel Core™ i3-7101E Processor (3M Cache, up to i3-7101E 3.90GHz, 65W) ® 7th Gen Intel Core™ i3-7101TE Processor (3M Cache, up to i3-7101TE 3.40GHz, 35W) ® i3-6100 6th Gen Intel Core™ i3-6100 Processor (3M Cache, 3.70GHz) ®...
1.4 Supported CPU List 1.5 Mechanical Dimension 1.5.1 Dimensions of IVH-9200M 1.5.2 Dimensions of IVH-9200 CHAPTER 2 GETTING TO KNOW YOUR IVH-9200 2.1 Packing List 2.2 Front Panel I/O & Functions 2.3 Rear Panel I/O & Functions 2.4 Main Board Expansion Connectors 2.5 Main Board Jumper &...
Page 7
CHAPTER 4 BIOS SETUP 4.1 Entering BIOS SETUP 4.2 Main 4.3 Advanced 4.4 Chipset 4.5 Security 4.6 Boot 4.7 Save & Exit APPENDIX A : Isolated DIO Guide APPENDIX B : Software Functions APPENDIX C : RAID Installation Guide APPENDIX D : Power Consumption APPENDIX E : Supported Memory &...
HD Graphics 630 supporting DirectX 12, OpenGL 4.4 and OpenCL 2.0 API, onboard DVI-I, DVI-D and DisplayPort display interfaces for Ultra HD 4K resolution, IVH-9200 makes new generation CPU performance, power efficiency, and graphics performance possible; PCIe 3.0 (8GT/s), Multiple SATA III (6Gbps), USB 3.0 (5Gbps), PoE (1Gbps) LAN and multiple wireless connections make seamless high-speed data conveying possible.
Page 10
Graphics ® Graphics Processor Intel HD Graphics P630/630/P530/530 Interface • DVI-I : Up to 1920 x 1200 @ 60Hz • DVI-D : Up to 1920 x 1200 @ 60Hz • DisplayPort : Up to 4096 x 2304 @ 60Hz Storage SATA 4 SATA III (6Gbps) support software RAID 0, 1, 5, 10 mSATA...
1.4 Supported CPU List Processor No. Cache Max. Frequency Embedded ® ® Intel Xeon E3-1275 v6 Up to 4.20 GHz ® ® Intel Xeon E3-1275 v5 Up to 4.00 GHz ® ® Intel Xeon E3-1225 v5 Up to 3.70 GHz ®...
2.1 Packing List Item Description IVH-9200 series In-Vehicle Fanless Embedded System (According to the configuration you order, the IVH-9200 series may contain SSD/HDD and DDR4 SO-DIMM. Please verify these items if necessary.) IVH-9200 series Accessory box which contains ● Vecow Drivers & Utilities DVD ●...
2.2 Front Panel I/O & Functions In Vecow IVH-9200 series family, all I/O connectors are located on front panel and rear panel. Most of the general connections to computer device, such as USB, LAN Jack, Audio, Display Port, DVI-I, DVI-D and any additional storage, are placed on the front panel.
Page 18
CFast socket cover before installing a CFast card. The IVH-9200 does not support the CFast hot swap and PnP (Plug and Play) functions. It is necessary to remove power source first before inserting or removing the CFast card.
Page 20
2.2.7 DisplayPort DVI-D SIM 2 SIM 3 LAN 1 SIM 1 WLAN CFast DVI-I LAN 2 Onboard Display Port supports auxiliary channel dual mode and the connection supports up to 4096x2304 resolution at 60 Hz. GETTING TO KNOW YOUR IVH-9200...
Page 21
There are 4 USB 3.0 connections available supporting up to 5GB per second data rate in the front side of IVH-9200. It is also compliant with the requirements of Super Speed (SS), High Speed (HS), Full Speed (FS) and Low Speed (LS).
Page 22
WLAN CFast DVI-I LAN 2 There are 2 audio connectors, Mic-in and Line-out, in the front side of IVH-9200. Onboard Realtek ALC892 audio codec supports 5.1 channel HD audio and fully ® complies with Intel High Definition Audio (Azalia) specifications.
HDD 3 HDD 2 HDD 4 There are 4 front-access 2.5” SSD/HDD trays in the front side of IVH-9200. Just trigger to open the SSD/HDD tray, up to 4TB is available. 2.3 Rear Panel I/O & Functions 2.3.1 Power Terminal Block...
Page 26
COM Port MB Connector COM Port MB Connector COM 3 COM 4 CN10 COM 3 & COM 4 MB connector pin out: Pin No. Signal Name Chassis GND CN9 (COM 3) CN10 (COM 4) CN10 GETTING TO KNOW YOUR IVH-9200...
Page 27
There are 4 USB 3.0 connections available supporting up to 5GB per second data rate in the rear side of IVH-9200. It is also compliant with the requirements of Super Speed (SS), High Speed (HS), Full Speed (FS) and Low Speed (LS).
Page 28
10Mbps 100Mbps 1000Mbps Right Solid Solid Bottom Led Green Orange Left Flash Flash Flash Bottom Led Yellow Yellow Yellow PoE LED indicator: LED Location LED Color Status LED 3 - 6 Solid Green PoE ON GETTING TO KNOW YOUR IVH-9200...
Page 30
DIO2_GND DIO2_VDC (6~48V Input) DI reference circuit: Sink Mode (NPN) Power DIO Connector Supply DI_COM (Pin 9) 6-48V DC DI (Pin1-8) Source Mode (PNP) Power DIO Connector Supply DI_COM (Pin 9) 6-48V DC DI (Pin1-8) GETTING TO KNOW YOUR IVH-9200...
Page 34
2.4.4 DDR4 Slot There are 2 DDR4 channel onboard supporting DDR4 2133/1866 and up to 32GB. (Each channel 16GB) SODIMM 2 SODIMM 1 Slot Description Slot Description SODIMM_1 DDR4 Channel A SODIMM_2 DDR4 Channel B GETTING TO KNOW YOUR IVH-9200...
Page 35
2.4.5 BIOS Socket If the BIOS needs to be changed, please contact the Vecow RMA service team. BIOS 2.4.6 SATA Connector Standard 7 PIN SATA Connector There are 4 onboard high performance Serial ATA III. It supports higher storage capacity with less cabling effort and smaller required space.
Page 36
2.4.8 Internal USB 2.0 Standard Vertical USB 2.0 Connector The IVH-9200 main board provides one expansion USB port using plug-and- play for Dongle Key or LCD touch Panel. The USB interface supports 480 Mbps transfer rate complied with high speed USB specification Rev. 2.0.
Page 38
Panasonic BR2032 190mAh lithium battery. It is recommended that you do not have to get the lithium battery on your own. If the battery needs to be changed, please contact the Vecow RMA service team. Battery GETTING TO KNOW YOUR IVH-9200...
Page 40
+3.3V LAD0 RESET# Ground LAD1 CLOCK LAD2 Ground 2.4.13 LAN IEEE 1588 Header IVH-9200 provides a LAN header for IEEE 1588. LAN No. Function Function Rear POE LAN3 Intel I210 Rear POE LAN4 Intel I210 Rear POE LAN5 Intel I210...
Page 41
2.4.14 COM Port Header IVH-9200 provides 4 COM port headers for internal COM port cable. CN10 Pin out: CN9: CN10: Pin No. Description Port Pin No. Description Port Ground_Frame COM 3 Ground_Frame COM 4 Ground COM 3 Ground COM 4...
Battery M2_CN1 The figure below is the top view of IVH-9200 main board which is the main board. It shows the location of the jumpers and the switches. You may configure your card to match the needs of your application by setting jumpers.
2.6.1 Adjust Ignition Control Modes IVH-9200 series provides 16 modes of different power on/off delay periods adjustable via SW2 switch. The default rotary switch is set to 0 in ATX/ AT power mode.
Page 48
Note: 1. DC power source and IGN share the same ground. 2. IVH-9200 supports 6V~36V wide range DC power input in ATX/AT mode. In Ignition mode, the input voltage is fixed to 12V/24V for car battery scenario. 3. For proper ignition control, the power button setting should be “Power down”...
SYSTEM SETUP 3.1 How to Open Your IVH-9200 Step 1 Remove SSD/HDD tray panel. Step 2 Remove six KHS#6-32 screws and take out front panel. HARDWARE INSTALLATION...
3.3 Installing DDR4 SO-DIMM Modules Step 1 Install DDR4 RAM module into SO-DIMM slot. Step 2 Make sure the RAM module is locked by the memory slot. HARDWARE INSTALLATION...
3.5 Installing Antenna Cable Step 1 Check Antenna cable and washers. Step 2 Put Antenna cable connector into the hole on the rear panel. Step 3 Fasten the washer on Antenna cable connector. HARDWARE INSTALLATION...
3.6 Installing CFast Card Step 1 Remove 2 pcs F-M3x4 screws on CFast & SIM cover. Step 2 Before inserting CFast & SIM Cards, make sure IVH-9200 power is not plugged. Step 3 Insert CFast card and push to lock.
3.7 Installing SIM Card Step 1 Remove two F-M3x4 screws on CFast & SIM cover. Step 2 Before inserting SIM Card, make sure the system power is not plugged. Step 3 Insert SIM card and push to lock. HARDWARE INSTALLATION...
Page 64
3.9.2 VESA Mount Step 1 IVH-9200 and VESA Mount. Step 2 Take IVH-9200 and VESA Mount with fasten 4pcs KHS#6-32 screws. HARDWARE INSTALLATION...
Page 66
3.9.3 Din Rail Kit Step 1 IVH-9200 and Din Rail Kit. Step 2 Take IVH-9200 & Din Rail Kit and fasten four KHS#6-32 screws in the four marked corners. HARDWARE INSTALLATION...
BIOS SETUP 4.1 Entering BIOS SETUP Figure 4-1: Entering Setup Screen BIOS provides an interface for users to check and change system configuration. The BIOS setup program is accessed by pressing the <Del> key when POST display output is shown. BIOS AND DRIVER SETTING...
Page 70
4.3.1 ACPI Settings Figure 4 3-1: ACPI Settings Enable Hibernation Enables or disables system's ability to hibernate (OS/S4 sleep state). This option may not be effective with some OS. ACPI Sleep State Selects the highest ACPI sleep state the system will enter when the SUSPEND button is pressed.
Page 72
Serial Port 1 Configuration Set parameters of serial port 1 (COM 1). Serial Port 2 Configuration Set parameters of serial port 2 (COM 2). Serial Port 3 Configuration Set parameters of serial port 3 (COM 3). Serial Port 4 Configuration Set parameters of serial port 4 (COM 4).
Page 74
CPU C state Enable or disable CPU C states. Enhanced C-states Enable/disable C1E. When enabled, CPU will switch to minimum speed when all cores enter C-State. Package C State limit Package C State limit. Intel TXT(LT) Support Enables or disables Intel (R) TXT (LT) support. 4.3.9 Intel TXT Information Figure 4 3-9: Intel TXT Information Display Intel TXT information.
Page 76
4.3.12 CSM Configuration Figure 4 3-12: CSM Settings CSM Support Enable/disable CSM support GateA20 Active UPON REQUEST - GA20 can be disabled using BIOS services. ALWAYS - do not allow GA20 to be disabled; this option is useful when any RT code is executed above 1MB.
Page 80
4.4.4 Memory Information of System Agent (SA) Figure 4-4-4: Memory Information Displays memory information. 4.4.5 PCH-IO Configuration Figure 4-4-5: PCH-IO Settings PCH LAN Controller Enable or disable onboard NIC. Wake on LAN Enable or disable integrated LAN to wake the system. (The wake On LAN cannot be disabled if ME is on at Sx state.) Serial IRQ Mode Configure serial IRQ mode.
4.6 Boot Figure 4-6: BIOS Boot Menu Setup Prompt Timeout Number of seconds to wait for setup activation key. 65535(0xFFFF) means indefinite waiting. Bootup NumLock State Select the keyboard NumLock state. Quiet Boot Enables or disables Quiet Boot option. Boot Option Sets the system boot order.
APPENDIX A : Isolated DIO Guide A.1 Function Description The IVH-9200 offers two 16-bit DIO (8-DI/ 8-DO) 20-pin terminal block connector. Each bit of DI and DO equipped with a photo-coupler for isolated protection. All IO pins are fixed by Hardware design and cannot change in/out direction in runtime process.
Page 88
Run batch file as Administrator. Runtime folder include head file for software developer or System Integration. Sample folder include Sample program, Driver package, and Driver API library. Source folder include Sample program source code that compile on Visual Studio 2008. This driver support to 32bit and 64bit version that are Windows 7 above.
Please select SATA device to RAID mode on BIOS menu. Advanced → SATA Configuration → SATA Mode Selection C.2 OS Installation IVH-9200 is featured with six SATA, include two internal SATA, three mSATA and one CFast. You can select one of SATA ports for OS installation We used CFast card for Windows 10 OS installation as an example.
Page 93
C.6 Create RAID Volume on “Rapid Storage Technology” Software IVH-9200 is featured with four SATA HDDs for RAID volume, so there are three options for choose on this page. Let’s take RAID 1 as example, please select ”RAID 1”.
Page 94
C.7 Disk Management : Partition the Disk After RAID 1 volume created, you can see the figure of SATA device allocation. You will find “Volume_0000” in SATA device at BIOS menu. To start Disk Management tool, select "initialize disk." Then add “Logical Device” for Windows access. C.8 If One SATA HDD on RAID Volume is Out-of-use After RAID 1 volume created, you can see the figure of SATA device allocation.
APPENDIX D : Power Consumption Testing Board IVH-9200 16GB x 2 USB-1 USB Keyboard Logitech K120 USB-2 USB Mouse Microsoft 1113 USB-3 USB Flash Transecnd 3.0 8GB USB-4 USB Flash Transecnd 3.0 8GB CFAST innodisk CFast 3ME3 64GB SATA 0...
Page 98
D.2 Intel® Core™ i5-6500TE@2.30GHz (6M Cache, 3.30 GHz) Power on and boot to Win8.1 64-bit Idle Status : Sleep Mode CPU usage less 3% Power Input Current Consumption Current Consumption Core™ i5- 0.928A 05.57W 3.464A 20.78W 6500TE Core™ i5- 0.598A 05.38W 2.286A 20.57W...