Table of Contents
Advertisement
The function of parameters
Parameter
Name of parameter
No.
Automatic reset in trip (trip retrial) can be set here. Trip can be is
automatically reset to allow operation to continue. Use this func-
tion only on such equipment that has no problem of safety even if
the motor is automatically restarted.
• Retrial is impossible if trip is by Overcurrent error
Sensor error
eter error
51
Retrial selection
When
When
set number of times. When 2 hours has elapsed with no trip, the
number of retrying times is initialized to 0.
Set the interval between retrials by " 52 Retrial start time". When
trip occurs in excess of preset number of trials, the brushless
amplifier outputs trip signal and stops.
• During retrial, trip signal is not output (It is stored in trip history)
You can set waiting time until retrial operation is performed after
52
Retrial start time
tripping is found. You can set 1 to 120 seconds.
Parameters can be initialized to the factory default.
<Initializing procedure>
Parameter
54
Cut off power with
initializing
again after display has disappeared, then
and parameters are initialized to the factory default.
Parameters can be copied.
(NO) Parameters are not copied
(PARAMETER-INITIALIZE):
57
Parameter copy
(PARAMETER-LOAD):
(PARAMETER-PROGRAM):
See the copying method of parameters on P.44 for detail
F0
For manufacturer use It cannot be changed.
62
Description
,
System error
,
User param-
,
or System parameter error
(NO) is selection, retrial is not effective.
to
is selection, retrial is made for the
(YES) selection, and turn on power
is displayed,
Initialization of Digital key pad data
Reading parameters into Digital key pad data
Writing parameters to the brushless amplifier
Outline of PANATERM for BL/ Example of an operation pattern
Outline of PANATERM for BL
Communicating software "PANATERM for BL" can do the following thing.
(1) Setting and saving of parameters of brushless amplifier and writing setting to memory
EEPROM.
(2) Monitor of input/output signals, monitor of a load factor.
(3) The present trip display and reference of a trip history.
,
(4) Data measurement of waveform graphics, and the call of preservation data.
.
Example of an operation pattern
When using the I 1 input, turn on the I 1 input enable switch (SW3) on the back of the
product and set the RUN switch on the front of the product to RUN.
When using the I 2 input, set the CCW / CW switch on the front of the product to CCW.
• Example of running pattern by use of 2nd acceleration / deceleration time.
When you choose " 32 Operation mode selection" at
mode, choose " 33 I 1/ I 2 function selection" at
REVERSE), and choose " 34 I 3 function selection" at
deceleration time.
1st acceleration time
Run/Stop switch (I1)
CCW/CW switch (I2)
2nd acceleration/
deceleration time (I3)
• Example of operation pattern in 2nd speed operation mode
When you choose " 32 Operation mode selection" at
mode, " I 3" is choosing of speed setting, and works as follows:
I 3
OFF
Internal speed (0-th speed ) or FIN
ON
1st acceleration time
CCW
Run/Stop switch (I1)
CCW/CW switch (I2)
1st speed (I3)
Internal speed
(0-th speed)
1st deceleration time
CCW
CW
Zero-speed
control
Internal speed
(0-th speed)
Speed setup
1st speed
1st speed
1st deceleration time
Internal speed
(0-th speed)
CW
Zero-speed control
: 1st speed operation
: (RUNSTOP, FORWARD-
: 2nd acceleration and
2nd acceleration time
2nd deceleration time
Zero-speed
control
: 2nd speed operation
63
Advertisement
Table of Contents
