Table of Contents
Advertisement
The function of parameters
Parameter
Name of parameter
No.
Run command can be chosen from the following:
(PANEL):
Command the motor to stop with switch of Digital key pad.
The motor cannot be operated by RUN switch on the front of
product or signal input " I 1" and " I 2". Signal input is effective
only in setting rotation direction, etc.
See " 33 I 1/ I 2 function selection".
Run command
(TERMINAL):
30
selection
RUN command is issued with the RUN switch on the front of
the product or with the signal inputs " I 1" and " I 2".
When commanding with the " I 1" signal input, turn SW3 on the
back of the product ON and use the RUN switch on the front of
the product to RUN to use.
When commanding with " I 2" signal input by setting the
parameter with " 33 I 1 / I 2 function selection", set the rotate
direction selector switch to CCW.
It is possible to select whether the 0th speed command setting is
performed with the front speed setting knob, " 00 setting speed
(0th speed)", or speed setting input "FIN"
Speed command
(PANEL): " 00 setting speed (0th speed)"
31
selection
(VOL-A): speed setting input "FIN"
(
Parameter for choosing operation mode
Setting
Operation mode
32
selection
(1) 2nd speed operation mode
I 3
OFF
ON
54
Description
(analog voltage speed setting)
:
VOL-F)
speed setting knob
Operation
Function of signal input
I 3
I 4
made
1st speed
Free-run stop
operation mode
External forced trip
2nd speed
2nd acceleration/deceleration time
Speed setting
operation mode
Trip reset
4th speed
Speed setting Speed setting
operation mode
8th speed
Speed setting Speed setting Speed setting
operation mode
Setting to be chosen
Speed setting knob, internal speed (0-th speed) or FIN
1st speed
" 32 Operation mode selection" Continued to the next page.
Parameter
Name of parameter
No.
Operation mode
32
selection
I 5
I 1/ I 2 function
33
selection
*1 Effective only when trip occurs
*2 When using the I 1 input, turn on the I 1 input enable switch (SW3) on the back of the product and
set the RUN switch on the front of the product to RUN.
When using the I 2 input, set the CCW / CW switch on the front of the product to CCW.
Description
(2) 4th speed operation mode
I 3
I 4
OFF OFF
Speed setting knob, internal speed (0-th speed) or FIN
ON
OFF
1st speed
OFF
ON
2nd speed
ON
ON
3rd speed
(3) 8th speed operation mode
I 3
I 4
I 5
Speed setting knob, internal speed (0-th
OFF OFF OFF
speed) or FIN
ON
OFF OFF
1st speed
OFF
ON
OFF
2nd speed
ON
ON
OFF
3rd speed
OFF OFF
ON
4th speed
ON
OFF
ON
5th speed
OFF
ON
ON
6th speed
ON
ON
ON
7th speed
(1) For setting " I 1" or " I 2" function
(FORWARD-REVERSE)
State of I 1
and I 2
I 1
I 2
OFF OFF
Deceleration stop when "16 Stop mode selection" is
ON
OFF
OFF
ON
ON
ON
Trip reset (which must be retained 0.2 sec or longer)
*2
(REVERSE - FORWARD)
State of I 1
and I 2
I 1
I 2
OFF OFF
Deceleration stop when "16 Stop mode selection" is
ON
OFF
OFF
ON
ON
ON
Trip reset (which must be retained 0.2 sec or longer)
" 33 I 1/ I 2 function selection" Continued to the next page.
Setting to be chosen
Setting to be chosen
Action
Stop
CCW run
CW run
Free-run stop
*1
Action
Stop
CW run
CCW run
Free-run stop
*1
55
Advertisement
Table of Contents
